Panasonic PT-D5500UL manual RS232C, Func

Page 35

RS232C

This sets the communication parameters at the serial terminals.

For details on the serial terminals, refer to “Using the serial terminals” (page 38).

IN BAUDRATE	: 9 600, 19 200 or 38 400 is
	selected.
IN PARITY	: NONE, EVEN or ODD is
	selected.

OUT BAUDRATE: 9 600, 19 200 or 38 400 is

	selected.
OUT PARITY	: NONE, EVEN or ODD is
	selected.
VPS SYSTEM	: MASTER or SLAVE is
	selected.
GROUP	: A to Z is selected. MASTER
	or SLAVE is also selected.

SYSTEM INFORMATION

The projector’s system information can be viewed.

SYSTEM INFORMATION

ROM VERSION	1. 00. 00
SET RUNTIME	300h
LAMP1 LOW	100h
HIGH	200h
TOTAL	300h
LAMP2 LOW	100h
HIGH	200h
TOTAL	300h
LAMP1 ON	20
LAMP2 ON	20
LAMP1 TYPE	LAD55
LAMP1 TYPE	LAD55

RETRN

FAN CONTROL1

The fan can be controlled in accordance with the operating conditions.

NORMAL : Standard setting

HIGHLAND : This is selected when using the projector at an altitude of over 1 400 meters.

FAN CONTROL2

The fan can be controlled in accordance with the direction in which the images are to be projected.

HORIZ. : Standard setting

VERTICAL : This is selected when projecting images at a significant angle toward the vertical (more than 30 degrees from the horizontal).

V

H	30 °	30 °	H
	30 °	30 °

V

H: HORIZ.

V: VERTICAL

Attention • Select the correct FAN CONTROL2 setting in accordance with the direction

in which the images are to be projected. Using the projector at the wrong FAN CONTROL2 setting will shorten the service life of the lamps.

FUNC 1

The user can set the function for the remote control’s FUNC1 button.

LAMP POW : The button functions in the same way as “LAMP POWER” of “OPTION2”.

ASPECT : The button functions in the same way as “ASPECT” of “POSITION”.

AUTO POW.OFF

The projector can be automatically set to the standby mode if no signals are input for the set duration.

DISABLE : Standard setting. This function

is set to OFF.

15MIN.–60MIN.: The duration can be set in 5- minute increments from 15 to 60 minutes.

Note • The auto power OFF function does not work while the freeze function is used.

PASSWORD

This function is used when a service person. Input the password with the numeric buttons (0 to

9)of the remote control and press ENTER button to confirm the entry.

35

Image 35

Contents Commercial Use PT-D5500ULModel number PT-D5500U/PT-D5500UL Dear Panasonic CustomerPage Contents Precautions with regard to safety Always disconnect all cables before moving the projector Insulate the battery using tape or similar before disposalDo not place liquid containers on top of the projector Do not insert any foreign objects into the projectorDo not use the old lamp unit AccessoriesUse only the Specified battery Do not look into the lens while the projector is being usedPrecautions on handling Name and function of parts Set to Computer When the operation mode selectorStatus LED lights Front and side of the projectorRear view of the main unit Controls on rear panel Side-mounted connection terminals Loading dry cells Using the remote control unitEffective range of remote control operation Operation mode selector switch Setting projector ID number to remote controlUsing the remote control as a PC mouse Using a wired remote control Projection distances InstallationInstallation geometry Projection schemesConnection Setup precautionsDigital Hi-vision video deck Example of connecting with AV productsDVD player Video deck Control PC Control PC DVI port DVI-D Cable Option ET-SCDV03 Example of connecting with PCsPC with How to remove the projection lens How to install the projection lensRoughly adjust the focus of the lens. Refer to Powering up the projectorMaking adjustment and selection Press the l button. on the main unit or the remote controlDirect power off function Powering off the projectorChoose an item and adjust it using buttons How to adjust the lensHow to adjust the lens position to the left or right Press the Shutter button again Automatic adjustment Auto SetupUsing the Freeze function Using the Shutter functionChange the magnification with the D.ZOOM + button Using the digital zoom D.ZOOM + functionPress the D.ZOOM + button of the remote control Languageenglish On-screen menusStructure of menu screens Returning to the previous Menu items settingResetting to the factory default Basic menu operationsAdjusting the picture KHz MHz Signal Scan Color FrequencySubcarrier SystemPosition Adjusting the positionENGLISH, DEUTSCH, FRANÇAIS, Español How to use Advanced MenuYpbpr Option 1 settingsLAMP2 Option 2 settingsDual LAMP1Func RS232CCycle of displayed internal test patterns Setting the passwordChanging the password Setting the textLAN cable Setting the network Connecting a PCSystem requirements Connection exampleExamples of connection Using the serial terminalsPin assignments and signal names Communication conditions Factory settingRemarks Control commandsCable specifications Connecting to a PC Computer Projector DTE specificationsSub 9-pin female external appearance Using the Remote 2 terminalPin assignments and control Lamp monitor Indication of lamp monitorMonitor ReplaceDismantle the air filter Cleaning and replacement of air filterProcedure of cleaning Clean the air filterReplacing the lamp unit Timing of lamp unit replacementHave a Phillips screwdriver ready ahead of time Lamp unit replacement stepsRemove the two screws securing the fan unit Select the lamp which has been replaced with the and buttons Click OK Using Web Browser ControlAccess procedure Basic controlStatus information Detail controlParameter Description Error informationWhen Failed has appeared for an item Mail setup DNS server setup Network configAdjust clock POP server setupNetwork status Password changeNot turn on Symptoms ChecksPower does Remote controlPT-D5500U PT-D5500UL SpecificationsWireless mouse receiver Length of power supply cord CabinetOutside dimensions Remote control Power sourceCompatible Signal List Calculation formulas for projection distance by lens types Projection distances by projection lensUnit mm inch DimensionsTrademark Acknowledgement Trademark acknowledgmentsConcernant LA Sécurité Ne pas retirer le couvercle ou le modifier Précautions concernant la sécuritéNe pas couvrir le filtre et la sortie d’air Ne pas surcharger la prise de courantNe pas placer d’objets lourds sur le projecteur Ne pas placer le projecteur sur des surfaces instablesNe pas placer des récipients de liquide sur le projecteur Ne pas mettre d’objets étrangers dans le projecteur’utilisez pas un bloc lampe usagé ’utiliser que la pile indiquéeMise au rebut Nettoyage et maintenancePrécautions pour la manipulation Précautions pour le transportPériode de remplacement de la lampe Remplacement de la lampePréparez un tournevis Phillips à l’avance Procédure de remplacement de la lampeLa lampe est chaude si elle vient d’être utilisée INIT. Compt Panasonic Canada Inc Technical Support