Outlaw Audio owner manual Model 1070 Specifications

Page 51

Owner’s Manual

Specifications

Model 1070 Specifications

Audio Section

Output Power (FTC) all channels driven

65 Watts per channel

 

 

(8Ω, 20Hz to 20kHz, <0.08% THD)

 

 

80 Watts per channel

 

 

(6Ω, 1kHz, <0.08% THD)

 

 

 

Input Impedance

26kΩ

 

 

 

Output Impedance (Main-RCA)

<600Ω

 

 

 

Pre Out

1V

 

 

 

Maximum Output

6V

 

 

 

Volume Range (Main)

-70dB to +10dB (0.5dB resolution)

 

 

 

Bass Management

 

 

 

 

 

High-Pass Slope

Crossover Frequency

 

(Small Speaker Setting)

(Adjustable 40/60/80/100/120/150Hz)

 

 

12 dB/octave (2nd order)

 

 

 

 

Low-Pass Slope (Subwoofer)

24dB/octave (4th order), 40-150Hz as above

 

 

 

Tone Control

 

 

 

 

 

Bass Center Frequency/Range

30Hz ± 6dB

 

 

 

 

Treble Center Frequency/Range

10KHz ± 6db

 

 

Frequency Response (Line)

10Hz to 100kHz ± 1dB

 

 

S/N Ratio (IHF-A)

100dB

 

 

IMD (CCIF @ 15Hz to 1kHz)

0.09%

FM Tuner Section

Sensitivity

 

IHF

10dBtyp.

 

 

 

 

50dB S/N

13dBtyp.

 

 

S/N Ratio

 

 

 

 

 

Mono

70dB

 

 

 

 

Stereo

67dB

 

 

Distortion

 

 

 

 

 

Mono

0.2%

 

 

 

 

Stereo

0.3%

 

 

Stereo Separation

40dB typ.

 

 

Adjacent Channel Selectivity

70dB ±400kHz

 

 

IF Rejection Ratio

120dB

 

 

Frequency Response

20 Hz to 15 kHz ± 1.5dB

Video Section (NTSC Format)

Bandwidth

 

Composite & S-Video

6 MHz –3dB

 

 

 

 

Component

>100MHz

 

 

Input Sensitivity @ 75Ω

 

 

 

 

 

Composite & S-Video

1.0Vp-p

 

 

 

 

Component R-Y Signal

0.5Vp-p

 

 

 

 

Component B-Y Signal

0.5Vp-p

 

 

 

 

Component Y Signal

1.0Vp-p

General

Supply Voltage

120V, 60Hz only

 

 

 

Power Consumption

 

 

 

 

 

Standby Power Off

1.9W

 

 

 

 

Idle

37W

 

 

 

 

@ Full Load

855W max.

 

 

Trigger Output

Sequential Delay 50 mA @ 12 VDC

 

 

Dimensions

 

 

 

 

 

Width

17.2 inches / 436.9 mm

 

 

 

 

Height

5.9 inches / 149.7 mm

 

 

 

 

Depth

15.5 inches / 393.7 mm

 

 

Weight

40 lbs. / 18.1 kg

AM Tuner Section

Sensitivity (20dB S/N)

200V

 

 

S/N

50dB

 

 

Selectivity

25dB

 

 

Distortion

0.7%

Digital Audio

All digital audio inputs and outputs are to S/PDIF electrical (75Ω, 0.5Vp-p), S/PDIF optical (Toslink), or AES / EBU (110Ω, 5Vp-p) standards as appropriate.

ProcessorCS49400

All features and specifications are subject to change without notice or liability to upgrade existing units.

Outlaw Audio and the Outlaw Audio logo are registered trademarks of Outlaw Audio, LLC.

Manufactured under license from Dolby Laboratories. Dolby, Pro Logic and the double-D symbol are registered trademarks of Dolby Laboratories.

Manufactured under license from DTS, Inc. DTS, DTS-ES, DTS 96/24 and DTS Neo:6 are registered trademarks of DTS, Inc.

Any trademark not acknowledged is recognized as the property of the respective owner.

Model 1070 7.1 Channel Surround Sound Receiver

51

Image 51
Contents Model Please Read First When the power-supply cord or plug is damagedInstallation Location Power CordHandle the AC Power Cord Gently WiringTable of Contents Brief Note On This Manual Outlaw Audio Model Channel Surround Sound ReceiverModel 1070 Front Panel AccessoriesActivates or cancels the on-screen menu UnpackingSelects between FM mono and FM stereo Adjusts the volume level of the headphonesModel 1070 Front Panel Selects between AM or FMModel 1070 Rear Panel RP25 Main Power button see pages 26 Model 1070 Rear PanelRP22 Preamp audio outputs see pages Other components begins the play function Remote ControlModel 1070 Remote Control These buttons control the Model 1070’s volumeOther components temporarily stops Play or Record Other components activates the recording functionDolby PLIIx-C Surround FormatsAvailable Surround Modes Model 1070 Front Panel and On Screen DisplayDolby Digital Dolby Digital EXDolby Pro Logic Stereo Listening Modes Connecting Your Model Connecting Audio ComponentsFor analog connections, remember that CD Player Connecting Audio Equipment to the ModelDigital TV Tuner/Cable Box/Satellite Receiver Connecting Video ComponentsDVD Player Video RecorderDVD-Audio/SACD/DVD Player Connecting a DVD Player to the ModelAudio Connection Note Connecting Other Video Components to the ModelAntenna Connections Loudspeaker ConnectionsGauge If the video display has an Hdmi input Connecting a Video Display to the ModelConnecting Loudspeakers to the Model PoweredOther Connections AC power connectionSubwoofer Connection Supplemental Amplifier ConnectionsWhen using a passive Connecting an External Amplifier to the ModelConnection Record Chart VideoAudio Here’s a brief explanation of each item on the Main menu System SetupInput Configuration Exit Takes you out of Menu modeInput Configuration sub-menu appears DVD Configuration sub-menu will appearInput choices appear as follows as you scroll through them There is no Lip Sync Delay available for audio-only sources Speaker PlacementUp to 200ms of delay can be selected in 10ms increments Configuring Audio InputsSurround Back Left and Right Speakers Speaker PlacementLeft Front, Center, and Right Front Speakers Left and Right Surround SpeakersSpeaker Size sub-menu appears Speaker Size ConfigurationTo enter settings for speaker size SubwoofersSpeaker X-Over sub-menu appears Speaker X-Over Crossover ConfigurationSelect LB/RB when you have two Surround Back speakers To enter settings for speaker crossoverPanorama Surround Setting ConfigurationsSurround Configuration sub-menu appears Night ModeChannel Subwoofer Offset DimensionHP Headphone Mode Channel CalibrationManual Channel Calibration with Your Own Test Source Channel Calibration sub-menu appearsChannel Calibration with the Model 1070 Test Tone As you desireDelay Adjust Delay Settings for Large RoomsTo set the Delay for each channel System Configuration Settings You can adjust the level from -70 to +10dBAvailable choices are Direct Operation PowerStandby/On indicator on the front panel will glow amber Model 1070 OperationUse this control to adjust the volume level Volume of the selected source will return at the new levelName of the selected source will reappear in the displays Channel Trim Night Mode SelectionNo Comp means no compression i.e., Night Mode Off Sleep TimerStereo will tune stereo signals Using the AM/FM TunerLip-Synch Delay Adjusting Tone ControlsTo select a preset station Using HeadphonesCreating an AM or FM station-memory preset manually To create FM station-memory presets automaticallyTo install batteries in the remote control Remote Control Setup and OperationBattery Installation Setup Using Preprogrammed CodesVolume Control Punch-Through LED will blink twiceYou can choose CBL, AUX, VCR, TV, SAT, CD, or AMP Backlighting Setup CodesOperation Source Selection ButtonsDVD Players Televisions TV/VCR Combos VCRs When You Are Away Care and MaintenanceSystem Reset CleaningTroubIeshooting Symptom Possible Cause Solution OptionsModel 1070 Specifications T l a w a u d i o Outlaw Audio Limited Warranty

1070 specifications

Outlaw Audio has made a name for itself in the high-performance audio market, and their Model 1070 receiver is a prime example of their commitment to delivering exceptional sound quality. The Outlaw Audio 1070 is a versatile surround sound receiver that combines advanced technology with user-friendly features, designed to elevate your home theater experience.

One of the standout features of the 1070 is its powerful amplification system. It delivers 7 channels of amplification, each capable of producing 60 watts per channel into 8 ohms. This robust power output ensures that even the most demanding audio tracks are handled with ease, providing clarity and depth across the frequency spectrum. The receiver is also equipped with an array of connection options, including HDMI inputs, to accommodate all of your audio and video sources seamlessly.

The 1070 employs advanced digital processing technologies that enhance your listening experience. It supports various surround sound formats, including Dolby Digital and DTS, allowing you to enjoy multidimensional audio for movies, music, and gaming. Outlaw Audio has integrated their proprietary Outlaw Bass Management system, which offers customizable bass settings to suit your room’s acoustics and your personal preferences. This feature ensures that your subwoofer delivers a seamless integration with your main speakers, enhancing the overall impact of your audio.

For those who appreciate fine-tuning their listening experience, the Outlaw 1070 includes an easy-to-use graphical user interface that simplifies setup and adjustment. The on-screen menus provide straightforward access to configuration settings, making it simple to calibrate your system for optimal performance.

Another key characteristic of the Outlaw 1070 is its build quality. The receiver is housed in a sturdy chassis, designed to minimize interference and reduce vibrations, a consideration that makes a difference in sound quality. The high-quality components and construction reflect Outlaw Audio’s dedication to crafting products that meet the expectations of audiophiles.

In conclusion, the Outlaw Audio 1070 offers a remarkable combination of power, flexibility, and advanced technologies that cater to both casual listeners and serious audiophiles alike. With its impressive amp capabilities, robust surround sound processing, and user-friendly design, the 1070 stands as a compelling choice for anyone looking to enhance their home audio system. Whether you’re enjoying a movie night or listening to your favorite music, the Outlaw Audio 1070 is engineered to deliver an immersive sound experience.