Outlaw Audio 1070 Speaker X-Over Crossover Configuration, Speaker X-Over sub-menu appears

Page 31

6.Proceed to enter a speaker “size” for each of the four positions

7.Use the and buttons on the front panel or remote to move the cursor to the SURR BACK OUT line.

You may skip this step if you have entered NONE for the SURR BACK SIZE setting. Here, you tell the system if you have a 6.1 or 7.1 system.

Select SBL if you are using a single Surround Back speaker. The ampli- fier channel for that speaker should be connected to the Surround Back Left speaker output (see the Connecting Loudspeakers to the Model 1070 diagram on page 22).

Select LB/RB when you have two Surround Back speakers.

8.Use the and buttons on the front panel or remote to move the cursor to the SUBWOOFER line.

When the front speakers are set to SMALL it is automatically set to YES and no further adjustment is required. However, when the front speak- ers are set to LARGE, this setting lets you determine where the LFE and derived bass is directed.

Select LFE to send the special Low Frequency Effects channel information on multichannel digital sources to the subwoofer while a full range front channel signal will be sent to the front Left/Right speakers along with the derived bass signal from the other speaker positions.

Selecting L/R+Sub tells your receiver that you want bass signals sent to your main L and R speakers in addition to your subwoofer. Choose this option only if your main L and R speakers have good bass handling capa- bility. It may be the best selection for medium-sized front speakers.

Select NONE to send all bass information, including both LFE and derived bass to the front left/right speakers.

9.When you have completed the configuration process for all main speaker positions and the subwoofer, use the and buttons on the front panel or remote to set the cursor to RETURN TO MAIN MENU.

10.Press SET on the front panel or the remote.

The Main Menu appears.

Speaker X-Over (Crossover) Configuration

A little theory before we begin. Think of a crossover as a dividing network that sends low frequencies to one speaker (usually the subwoofer) and higher frequencies to another speaker (your front L and R speakers, etc.) If this is a bit too technical just remember that a crossover lets the drivers (the domes, cones, ribbons, etc.) in your speakers work efficiently to reproduce only the frequency range they were designed to handle. Your Model 1070 lets you set different crossover points for front, surround, and surround back speakers so you can enjoy the best performance with the speakers you’ve chosen.

To make these settings as accurate as possible, you may want to consult the owner’s manual for your speakers before entering the crossover settings. Look at the specs for the speakers and find the lowest frequency each speaker can handle. That is the number you want enter in this menu.

Owner’s Manual

System Setup

To enter settings for speaker crossover:

1.Press the MENU button on the front panel or the remote to display the Main Menu.

The Main Menu appears on-screen:

MAIN MENU

> INPUT

CONFIG

SPEAKER

SIZE

SPEAKER

X-OVER

SURROUND

CONFIG

CHANNEL

CALIBRATION

DELAY

ADJUST

SYSTEM

CONFIG

EXIT

 

2.Move the cursor to SPEAKER X-OVER by using the and buttons on the front panel or remote.

3.With the cursor pointing to SPEAKER X-OVER, press SET on the front panel or the remote.

The Speaker X-Over sub-menu appears:

speaker x-over

> front l/r

:100Hz

center

:100Hz

Surr

L/R

:100Hz

surr

back L/R

:100Hz

return to main menu

4.Use the and buttons on the front panel or remote to move to each line on this menu.

5.Press the and buttons on the front panel or remote to select the correct crossover setting for each speaker position.

When SMALL has been chosen as the “size” for a speaker position, the available choices are:

40Hz60Hz80Hz100Hz120Hz150Hz

NOTE: When LARGE is selected on the SPEAKER SIZE menu a full range signal will be sent to the speaker position being adjusted. When NONE is selected on the SPEAKER SIZE menu, no adjustment is needed or possible.

6.When you have completed the configuration process for all main speaker positions, use the and buttons on the front panel or remote to set the cursor to RETURN TO MAIN MENU.

7.Press SET on the front panel or the remote.

The Main Menu appears.

Model 1070 7.1 Channel Surround Sound Receiver

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Model Please Read First When the power-supply cord or plug is damagedInstallation Location Power CordHandle the AC Power Cord Gently WiringTable of Contents Brief Note On This Manual Outlaw Audio Model Channel Surround Sound ReceiverModel 1070 Front Panel AccessoriesActivates or cancels the on-screen menu UnpackingSelects between FM mono and FM stereo Adjusts the volume level of the headphonesModel 1070 Front Panel Selects between AM or FMModel 1070 Rear Panel Model 1070 Rear Panel RP25 Main Power button see pages 26RP22 Preamp audio outputs see pages Other components begins the play function Remote ControlModel 1070 Remote Control These buttons control the Model 1070’s volumeOther components temporarily stops Play or Record Other components activates the recording functionDolby PLIIx-C Surround FormatsAvailable Surround Modes Model 1070 Front Panel and On Screen DisplayDolby Digital EX Dolby DigitalDolby Pro Logic Stereo Listening Modes Connecting Audio Components Connecting Your ModelFor analog connections, remember that CD Player Connecting Audio Equipment to the ModelDigital TV Tuner/Cable Box/Satellite Receiver Connecting Video ComponentsDVD Player Video RecorderDVD-Audio/SACD/DVD Player Connecting a DVD Player to the ModelAudio Connection Note Connecting Other Video Components to the ModelLoudspeaker Connections Antenna ConnectionsGauge If the video display has an Hdmi input Connecting a Video Display to the ModelConnecting Loudspeakers to the Model PoweredOther Connections AC power connectionSubwoofer Connection Supplemental Amplifier ConnectionsWhen using a passive Connecting an External Amplifier to the ModelVideo Connection Record ChartAudio Here’s a brief explanation of each item on the Main menu System SetupInput Configuration Exit Takes you out of Menu modeDVD Configuration sub-menu will appear Input Configuration sub-menu appearsInput choices appear as follows as you scroll through them There is no Lip Sync Delay available for audio-only sources Speaker PlacementUp to 200ms of delay can be selected in 10ms increments Configuring Audio InputsSurround Back Left and Right Speakers Speaker PlacementLeft Front, Center, and Right Front Speakers Left and Right Surround SpeakersSpeaker Size sub-menu appears Speaker Size ConfigurationTo enter settings for speaker size SubwoofersSpeaker X-Over sub-menu appears Speaker X-Over Crossover ConfigurationSelect LB/RB when you have two Surround Back speakers To enter settings for speaker crossoverPanorama Surround Setting ConfigurationsSurround Configuration sub-menu appears Night ModeChannel Subwoofer Offset DimensionHP Headphone Mode Channel CalibrationManual Channel Calibration with Your Own Test Source Channel Calibration sub-menu appearsChannel Calibration with the Model 1070 Test Tone As you desireDelay Settings for Large Rooms Delay AdjustTo set the Delay for each channel You can adjust the level from -70 to +10dB System Configuration SettingsAvailable choices are Direct Operation PowerStandby/On indicator on the front panel will glow amber Model 1070 OperationVolume of the selected source will return at the new level Use this control to adjust the volume levelName of the selected source will reappear in the displays Channel Trim Night Mode SelectionNo Comp means no compression i.e., Night Mode Off Sleep TimerStereo will tune stereo signals Using the AM/FM TunerLip-Synch Delay Adjusting Tone ControlsTo select a preset station Using HeadphonesCreating an AM or FM station-memory preset manually To create FM station-memory presets automaticallyTo install batteries in the remote control Remote Control Setup and OperationBattery Installation Setup Using Preprogrammed CodesLED will blink twice Volume Control Punch-ThroughYou can choose CBL, AUX, VCR, TV, SAT, CD, or AMP Backlighting Setup CodesOperation Source Selection ButtonsDVD Players Televisions TV/VCR Combos VCRs When You Are Away Care and MaintenanceSystem Reset CleaningTroubIeshooting Symptom Possible Cause Solution OptionsModel 1070 Specifications T l a w a u d i o Outlaw Audio Limited Warranty

1070 specifications

Outlaw Audio has made a name for itself in the high-performance audio market, and their Model 1070 receiver is a prime example of their commitment to delivering exceptional sound quality. The Outlaw Audio 1070 is a versatile surround sound receiver that combines advanced technology with user-friendly features, designed to elevate your home theater experience.

One of the standout features of the 1070 is its powerful amplification system. It delivers 7 channels of amplification, each capable of producing 60 watts per channel into 8 ohms. This robust power output ensures that even the most demanding audio tracks are handled with ease, providing clarity and depth across the frequency spectrum. The receiver is also equipped with an array of connection options, including HDMI inputs, to accommodate all of your audio and video sources seamlessly.

The 1070 employs advanced digital processing technologies that enhance your listening experience. It supports various surround sound formats, including Dolby Digital and DTS, allowing you to enjoy multidimensional audio for movies, music, and gaming. Outlaw Audio has integrated their proprietary Outlaw Bass Management system, which offers customizable bass settings to suit your room’s acoustics and your personal preferences. This feature ensures that your subwoofer delivers a seamless integration with your main speakers, enhancing the overall impact of your audio.

For those who appreciate fine-tuning their listening experience, the Outlaw 1070 includes an easy-to-use graphical user interface that simplifies setup and adjustment. The on-screen menus provide straightforward access to configuration settings, making it simple to calibrate your system for optimal performance.

Another key characteristic of the Outlaw 1070 is its build quality. The receiver is housed in a sturdy chassis, designed to minimize interference and reduce vibrations, a consideration that makes a difference in sound quality. The high-quality components and construction reflect Outlaw Audio’s dedication to crafting products that meet the expectations of audiophiles.

In conclusion, the Outlaw Audio 1070 offers a remarkable combination of power, flexibility, and advanced technologies that cater to both casual listeners and serious audiophiles alike. With its impressive amp capabilities, robust surround sound processing, and user-friendly design, the 1070 stands as a compelling choice for anyone looking to enhance their home audio system. Whether you’re enjoying a movie night or listening to your favorite music, the Outlaw Audio 1070 is engineered to deliver an immersive sound experience.
Top Page Image Contents