Outlaw Audio 1070 Left Front, Center, and Right Front Speakers, Left and Right Surround Speakers

Page 29

Owner’s Manual

System Setup

Left Front, Center, and Right Front Speakers

Place them at the same relative height and, if at all possible, a bit away from any walls. Some acousticians recommend placement far away from any walls but that may not be practical in your situation.

Most speakers sound best with the tweeter positioned at “seated ear height”; the same height your ears are when you’re ready to watch and listen.

Take care to aim the speakers at your prime viewing/listening position. That will probably mean that the center channel speaker will be aimed straight ahead while the left and right speakers are “toed-in” a bit.

Left and Right Surround Speakers

Put these speakers about 3' (1 meter to you metric Outlaws) above your “seated ear height.”

Mount them on the side walls of your listening room, preferably a bit to the rear of the prime seating position, if possible. Different authorities have dif- ferent ideas here but, if the speakers are at the right height, you can vary their placement from slightly behind to slightly ahead of your prime viewing/ listening position.

If your surround speakers are dipolar rather than directional, remember to ori- ent the arrows on the dipole enclosures properly. For speakers on the side walls, point the arrows to the front of the room (i.e., towards the video display).

Surround Back Left and Right Speakers

Note: These speakers are required for Dolby Digital EX, DTS-ES, Dolby Pro Logic IIx, a nd 7-Channel Stereo. They are also desirable, though not required, for DTS Neo:6.

Put these speakers about 3’ (or 1 meter) above your “seated ear height.”

Place them on the rear wall, behind the prime viewing/listening position so that the angle between each speaker and the listener is approximately 30 degrees. If that’s confusing, try “dividing” the rear wall into thirds and placing the speakers at the 1/3 points on the back wall.

Dipoles placed on a rear or back wall should have the arrows pointing toward each other to achieve the correct acoustical image in the room.

If you’re using just one surround back speaker, center it directly behind your main viewing/listening area.

Speaker Placement

Model 1070 7.1 Channel Surround Sound Receiver

29

Image 29
Contents Model Please Read First When the power-supply cord or plug is damagedHandle the AC Power Cord Gently Power CordWiring Installation LocationTable of Contents Brief Note On This Manual Outlaw Audio Model Channel Surround Sound ReceiverActivates or cancels the on-screen menu AccessoriesUnpacking Model 1070 Front PanelModel 1070 Front Panel Adjusts the volume level of the headphonesSelects between AM or FM Selects between FM mono and FM stereoModel 1070 Rear Panel RP22 Preamp audio outputs see pages RP25 Main Power button see pages 26Model 1070 Rear Panel Model 1070 Remote Control Remote ControlThese buttons control the Model 1070’s volume Other components begins the play functionOther components temporarily stops Play or Record Other components activates the recording functionAvailable Surround Modes Surround FormatsModel 1070 Front Panel and On Screen Display Dolby PLIIx-CDolby Pro Logic Dolby DigitalDolby Digital EX Stereo Listening Modes For analog connections, remember that Connecting Your ModelConnecting Audio Components CD Player Connecting Audio Equipment to the ModelDVD Player Connecting Video ComponentsVideo Recorder Digital TV Tuner/Cable Box/Satellite ReceiverDVD-Audio/SACD/DVD Player Connecting a DVD Player to the ModelAudio Connection Note Connecting Other Video Components to the ModelGauge Antenna ConnectionsLoudspeaker Connections If the video display has an Hdmi input Connecting a Video Display to the ModelConnecting Loudspeakers to the Model PoweredSubwoofer Connection AC power connectionSupplemental Amplifier Connections Other ConnectionsWhen using a passive Connecting an External Amplifier to the ModelAudio Connection Record ChartVideo Input Configuration System SetupExit Takes you out of Menu mode Here’s a brief explanation of each item on the Main menuInput choices appear as follows as you scroll through them Input Configuration sub-menu appearsDVD Configuration sub-menu will appear Up to 200ms of delay can be selected in 10ms increments Speaker PlacementConfiguring Audio Inputs There is no Lip Sync Delay available for audio-only sourcesLeft Front, Center, and Right Front Speakers Speaker PlacementLeft and Right Surround Speakers Surround Back Left and Right SpeakersTo enter settings for speaker size Speaker Size ConfigurationSubwoofers Speaker Size sub-menu appearsSelect LB/RB when you have two Surround Back speakers Speaker X-Over Crossover ConfigurationTo enter settings for speaker crossover Speaker X-Over sub-menu appearsSurround Configuration sub-menu appears Surround Setting ConfigurationsNight Mode PanoramaHP Headphone Mode DimensionChannel Calibration Channel Subwoofer OffsetChannel Calibration with the Model 1070 Test Tone Channel Calibration sub-menu appearsAs you desire Manual Channel Calibration with Your Own Test SourceTo set the Delay for each channel Delay AdjustDelay Settings for Large Rooms Available choices are System Configuration SettingsYou can adjust the level from -70 to +10dB Standby/On indicator on the front panel will glow amber PowerModel 1070 Operation Direct OperationName of the selected source will reappear in the displays Use this control to adjust the volume levelVolume of the selected source will return at the new level No Comp means no compression i.e., Night Mode Off Night Mode SelectionSleep Timer Channel TrimLip-Synch Delay Using the AM/FM TunerAdjusting Tone Controls Stereo will tune stereo signalsCreating an AM or FM station-memory preset manually Using HeadphonesTo create FM station-memory presets automatically To select a preset stationBattery Installation Remote Control Setup and OperationSetup Using Preprogrammed Codes To install batteries in the remote controlYou can choose CBL, AUX, VCR, TV, SAT, CD, or AMP Volume Control Punch-ThroughLED will blink twice Operation Setup CodesSource Selection Buttons BacklightingDVD Players Televisions TV/VCR Combos VCRs System Reset Care and MaintenanceCleaning When You Are AwayTroubIeshooting Symptom Possible Cause Solution OptionsModel 1070 Specifications T l a w a u d i o Outlaw Audio Limited Warranty

1070 specifications

Outlaw Audio has made a name for itself in the high-performance audio market, and their Model 1070 receiver is a prime example of their commitment to delivering exceptional sound quality. The Outlaw Audio 1070 is a versatile surround sound receiver that combines advanced technology with user-friendly features, designed to elevate your home theater experience.

One of the standout features of the 1070 is its powerful amplification system. It delivers 7 channels of amplification, each capable of producing 60 watts per channel into 8 ohms. This robust power output ensures that even the most demanding audio tracks are handled with ease, providing clarity and depth across the frequency spectrum. The receiver is also equipped with an array of connection options, including HDMI inputs, to accommodate all of your audio and video sources seamlessly.

The 1070 employs advanced digital processing technologies that enhance your listening experience. It supports various surround sound formats, including Dolby Digital and DTS, allowing you to enjoy multidimensional audio for movies, music, and gaming. Outlaw Audio has integrated their proprietary Outlaw Bass Management system, which offers customizable bass settings to suit your room’s acoustics and your personal preferences. This feature ensures that your subwoofer delivers a seamless integration with your main speakers, enhancing the overall impact of your audio.

For those who appreciate fine-tuning their listening experience, the Outlaw 1070 includes an easy-to-use graphical user interface that simplifies setup and adjustment. The on-screen menus provide straightforward access to configuration settings, making it simple to calibrate your system for optimal performance.

Another key characteristic of the Outlaw 1070 is its build quality. The receiver is housed in a sturdy chassis, designed to minimize interference and reduce vibrations, a consideration that makes a difference in sound quality. The high-quality components and construction reflect Outlaw Audio’s dedication to crafting products that meet the expectations of audiophiles.

In conclusion, the Outlaw Audio 1070 offers a remarkable combination of power, flexibility, and advanced technologies that cater to both casual listeners and serious audiophiles alike. With its impressive amp capabilities, robust surround sound processing, and user-friendly design, the 1070 stands as a compelling choice for anyone looking to enhance their home audio system. Whether you’re enjoying a movie night or listening to your favorite music, the Outlaw Audio 1070 is engineered to deliver an immersive sound experience.