Epson SE450 manual ESC L Set Feed Length, ESC M Set Font to 12 cpi

Page 30

Command Reference

ASCII	ESC J n
Decimal	27 74 n
Hex	1B 4A n

Parameters

n = the desired number of sublines to feed

ESC L Set Feed Length

Description

Provided for LabelWriter raster compatibility.

See the GS L command for information.

See Also

GS L

ESC M Set Font to 12 cpi

Description

Changes to the 12 cpi normal font. The cell dimension is 32 H x 16 W. This is the default font.

Fonts may only be changed at the beginning of a line, prior to any printable characters. This font will remain in effect until the printer is reset (by the ESC @ or ESC * command) or another font is selected.

See Also

ESC P

ESC S

ESC T

ESC U

Expression

ASCII	ESC M
Decimal	27 77
Hex	1B 4D

Parameters

None

	Font	Height	Width	Horizontal	Vertical cpi
	Font	Height	Width	cpi	Vertical cpi
				cpi
	ESC S	16	10	20.3	12.7

24

Image 30

Contents Technical Reference Copyright Contents Page Character Codes Configuration Menu Printer Specifications This page intentionally left blank for double-sided printing Introduction This page intentionally left blank for double-sided printing Configuring the Host Computer for RS-232 Serial Interface RS-232 SettingsRS-232 Signal Levels RS-232 CablingProgramming Overview Programming the LabelWriter PrinterCharacter Evaluation Resetting the PrinterCommand Parameters Bit Character ParametersConversions Font Specifications ObjectsPrint Modes Raster Mode OrientationLandscape Mode Text ObjectsBarcode Objects Graphic Objects Line ObjectsCommand Reference Alphabetical Command ListESC L Commands by Function Position ControlFont Control GS DC2 GS DC3 GS RS GS USBarcodes MiscellaneousPrintable Characters Commands Raster Compatibility20h FFh Printable Characters DC4 Cancel Double Wide Mode CR Carriage ReturnESC a Return Printer Status ESC a Return Hardware StatusESC B Set Dot Tab ESC c Set Print Temperature to Low ESC d Set Print Temperature to MediumESC D Set Bytes per Line ESC e Set Print Temperature to Default ESC E Form FeedESC h Set Print Speed to Fast ESC g Set Print Temperature to HighESC F 1 n Feed n Lines ESC i Set Printing Speed to BarcodeESC L Set Feed Length ESC M Set Font to 12 cpiESC P Set Font to 16 cpi ESC Q Set Top Margin ESC S Set Font to 20 cpiESC T Set Font to 7 cpi ESC U Set Font to 10 cpi ESC V Return Firmware Revision ESC W Wrap DataESC X Set Horizontal Starting Position ESC Y Set Vertical Starting PositionESC y Set 203 x 203 dpi ESC * Reset to DefaultsESC @ Reset to Power-up Condition ESC z Set 136 x 203 dpiETB Raster Mode Compressed Graphics FF Form Feed GS a Starting Position of Bar Code GS DC2 Set Font to Double HeightGS DC3 Cancel Double Height GS d Feed n Text LinesGS h Set Barcode Height GS k Print BarcodeData Matrix Barcode UPC-ASupported Square Data Matrix Symbol Sizes Supported Rectangular Data Matrix Symbol Sizes Commands Command Reference GS l Draw Line in Landscape Mode Least significant byte of the line length in dots GS L Set Feed Length GS RS Set Inverse Print Mode GS q Print UPC/EAN ChecksumGS S Return Printer Status ReturnsGS T Select Line Wrap/Truncate Modes GS t Set Characters per Line in LandscapeGS US Cancel Inverse Print Mode GS u Set Characters per Line in PortraitGS V Set Print Orientation GS W Set Bar Code Element WidthGS ~ Enter Debug Mode GS w Set Barcode Module WidthGS * Landscape Mode Graphics SO Set Font to Double Wide Mode HT Horizontal TabLF Line Feed SYN Raster Mode Graphics Caret Feature Activating the Caret FeatureUsing the Caret Feature Command Reference Character Codes CharCharacter Codes CharName \ back slash DEL Name Decimal Hex Binary Caret Feature Character Codes 251 1111 252 253 254 255 This page intentionally left blank for double-sided printing Configuration Menu Configuration Menu Interface Specifications Printer SpecificationsHardware Specifications Print Head SpecificationsPrinter Specifications USB Settings Serial Interface SpecificationsThis page intentionally left blank for double-sided printing