Epson SE450 manual Configuration Menu

Page 71

Chapter 5

Configuration Menu

The LabelWriter SE450 printer has a Printer Configuration Menu built into the firmware. Through this menu, flash memory settings such as baud rate and feed distance can be changed. Flash memory settings remain in effect even after power has been removed from the printer.

The Printer Configuration Menu is accessible by using any terminal communications (modem) program (such as, Hyperterminal in Windows) and communicating with the printer through an RS-232 serial port. The communications software MUST be configured to operate as follows:

9600 baud, no parity, 8 data bits, and 1 stop bit

To access the Printer Configuration menu

1.Load labels in the printer and connect the serial cable.

2.Disconnect power to the printer.

3.Press and hold down the form feed button.

4.While the form feed button is pressed, connect the power cord.

5.Continue to hold the form feed button down for five more seconds. The green light will blink.

6.Release the feed button.

7.Start your communications software.

8.Press <Enter> until the menu appears.

Dymo LabelWriter SE450

Firmware Version 1765303v0G

Printer Configuration Menu

Type ? for help

9.Press ? for help.

You should see the following on your screen:

-?

B? Display Baud Rate

B0 Set 1200 Baud

B1 Set 2400 Baud

B2 Set 4800 Baud

B3 Set 9600 Baud

65

Image 71

Contents Technical Reference Copyright Contents Page Character Codes Configuration Menu Printer Specifications This page intentionally left blank for double-sided printing Introduction This page intentionally left blank for double-sided printing RS-232 Settings Configuring the Host Computer for RS-232 Serial InterfaceRS-232 Cabling RS-232 Signal LevelsProgramming the LabelWriter Printer Programming OverviewBit Character Parameters Resetting the PrinterCommand Parameters Character EvaluationConversions Print Modes Font SpecificationsObjects Orientation Raster ModeText Objects Landscape ModeBarcode Objects Line Objects Graphic ObjectsAlphabetical Command List Command ReferenceESC L Position Control Commands by FunctionGS DC2 GS DC3 GS RS GS US Font ControlPrintable Characters BarcodesMiscellaneous 20h FFh Printable Characters CommandsRaster Compatibility CR Carriage Return DC4 Cancel Double Wide ModeESC B Set Dot Tab ESC a Return Printer StatusESC a Return Hardware Status ESC D Set Bytes per Line ESC c Set Print Temperature to LowESC d Set Print Temperature to Medium ESC E Form Feed ESC e Set Print Temperature to DefaultESC i Set Printing Speed to Barcode ESC g Set Print Temperature to HighESC F 1 n Feed n Lines ESC h Set Print Speed to FastESC M Set Font to 12 cpi ESC L Set Feed LengthESC P Set Font to 16 cpi ESC T Set Font to 7 cpi ESC Q Set Top MarginESC S Set Font to 20 cpi ESC U Set Font to 10 cpi ESC W Wrap Data ESC V Return Firmware RevisionESC Y Set Vertical Starting Position ESC X Set Horizontal Starting PositionESC z Set 136 x 203 dpi ESC * Reset to DefaultsESC @ Reset to Power-up Condition ESC y Set 203 x 203 dpiETB Raster Mode Compressed Graphics FF Form Feed GS DC2 Set Font to Double Height GS a Starting Position of Bar CodeGS d Feed n Text Lines GS DC3 Cancel Double HeightGS k Print Barcode GS h Set Barcode HeightUPC-A Data Matrix BarcodeSupported Square Data Matrix Symbol Sizes Supported Rectangular Data Matrix Symbol Sizes Commands Command Reference GS l Draw Line in Landscape Mode Least significant byte of the line length in dots GS L Set Feed Length GS q Print UPC/EAN Checksum GS RS Set Inverse Print ModeReturns GS S Return Printer StatusGS t Set Characters per Line in Landscape GS T Select Line Wrap/Truncate ModesGS u Set Characters per Line in Portrait GS US Cancel Inverse Print ModeGS W Set Bar Code Element Width GS V Set Print OrientationGS w Set Barcode Module Width GS ~ Enter Debug ModeGS * Landscape Mode Graphics LF Line Feed SO Set Font to Double Wide ModeHT Horizontal Tab SYN Raster Mode Graphics Using the Caret Feature Caret FeatureActivating the Caret Feature Command Reference Char Character CodesCharacter Codes CharName \ back slash DEL Name Decimal Hex Binary Caret Feature Character Codes 251 1111 252 253 254 255 This page intentionally left blank for double-sided printing Configuration Menu Configuration Menu Print Head Specifications Printer SpecificationsHardware Specifications Interface SpecificationsPrinter Specifications Serial Interface Specifications USB SettingsThis page intentionally left blank for double-sided printing