Epson SE450 manual GS l Draw Line in Landscape Mode

Page 47

Commands

e = user defined error correction level (0 to 8), if it is 0 which means the error correction level will be set according to PDF417 specification. It will be assigned as per the following Table:

Error Correction

Number of Data

Error Correction Level

CodewordsCodewords

0

2

--

1

4

1-40

2

8

1-40

3

16

41-160

4

32

161

5

64

320

6

128

> 321

7

256

--

8

512

--

m1 = the most significant byte of data length.

m2= the least significant byte of data length.

Total data length = m1 * 256 + m2

Example

GS ‘k’ 0x0E 0x0 0x0 0x0 0x0 0x23 “This is a PDF417 Test, test 1234567”

prints the following PDF417 image:

GS l Draw Line in Landscape Mode

Description

Draws a line in landscape mode. The thickness of the line is determined by the bit set by the bitmask, m.

Expression

ASCII

GS l n1 n2 L1 L2 m

Decimal

29 108 n1 n2 L1 L2 m

Hex

1D 6C n1 n2 L1 L2 m

41

Image 47
Contents Technical Reference Copyright Contents Page Character Codes Configuration Menu Printer Specifications This page intentionally left blank for double-sided printing Introduction This page intentionally left blank for double-sided printing RS-232 Settings Configuring the Host Computer for RS-232 Serial InterfaceRS-232 Cabling RS-232 Signal LevelsProgramming the LabelWriter Printer Programming OverviewBit Character Parameters Resetting the PrinterCommand Parameters Character EvaluationConversions Print Modes Font SpecificationsObjects Orientation Raster ModeText Objects Landscape ModeBarcode Objects Line Objects Graphic ObjectsAlphabetical Command List Command ReferenceESC L Position Control Commands by FunctionGS DC2 GS DC3 GS RS GS US Font ControlPrintable Characters BarcodesMiscellaneous 20h FFh Printable Characters CommandsRaster Compatibility CR Carriage Return DC4 Cancel Double Wide ModeESC B Set Dot Tab ESC a Return Printer StatusESC a Return Hardware Status ESC D Set Bytes per Line ESC c Set Print Temperature to LowESC d Set Print Temperature to Medium ESC E Form Feed ESC e Set Print Temperature to DefaultESC i Set Printing Speed to Barcode ESC g Set Print Temperature to HighESC F 1 n Feed n Lines ESC h Set Print Speed to FastESC M Set Font to 12 cpi ESC L Set Feed LengthESC P Set Font to 16 cpi ESC T Set Font to 7 cpi ESC Q Set Top MarginESC S Set Font to 20 cpi ESC U Set Font to 10 cpi ESC W Wrap Data ESC V Return Firmware RevisionESC Y Set Vertical Starting Position ESC X Set Horizontal Starting PositionESC z Set 136 x 203 dpi ESC * Reset to DefaultsESC @ Reset to Power-up Condition ESC y Set 203 x 203 dpiETB Raster Mode Compressed Graphics FF Form Feed GS DC2 Set Font to Double Height GS a Starting Position of Bar CodeGS d Feed n Text Lines GS DC3 Cancel Double HeightGS k Print Barcode GS h Set Barcode HeightUPC-A Data Matrix BarcodeSupported Square Data Matrix Symbol Sizes Supported Rectangular Data Matrix Symbol Sizes Commands Command Reference GS l Draw Line in Landscape Mode Least significant byte of the line length in dots GS L Set Feed Length GS q Print UPC/EAN Checksum GS RS Set Inverse Print ModeReturns GS S Return Printer StatusGS t Set Characters per Line in Landscape GS T Select Line Wrap/Truncate ModesGS u Set Characters per Line in Portrait GS US Cancel Inverse Print ModeGS W Set Bar Code Element Width GS V Set Print OrientationGS w Set Barcode Module Width GS ~ Enter Debug ModeGS * Landscape Mode Graphics LF Line Feed SO Set Font to Double Wide ModeHT Horizontal Tab SYN Raster Mode Graphics Using the Caret Feature Caret FeatureActivating the Caret Feature Command Reference Char Character CodesCharacter Codes CharName \ back slash DEL Name Decimal Hex Binary Caret Feature Character Codes 251 1111 252 253 254 255 This page intentionally left blank for double-sided printing Configuration Menu Configuration Menu Print Head Specifications Printer SpecificationsHardware Specifications Interface SpecificationsPrinter Specifications Serial Interface Specifications USB SettingsThis page intentionally left blank for double-sided printing