Epson SE450 manual Commands

Page 45

Commands

GS 0x6B 0x0F 0xC0 0x00 0x00 0x00 0x05 0x3132333435

Prints the following image:

Here, 5 characters are also sent: ABCDE. However, since they are not all numbers, compression is not used. Rectangles are not excluded, so an 8x18 symbol should be auto- selected. The element size has been set to 5.

GS ‘k’ 15 t r c m1 m2 dl…dm

GS 0x6B 0x0F 0x05 0x00 0x00 0x00 0x05 0x4142434445

Prints the following image:

PDF417 2D Barcode

PDF417 is a barcode symbology with the following basic characteristics:

nEncodable Character Set:

Text compaction mode permits all printable ASCII characters to be encoded, i.e. values 32-126 inclusive in accordance with ISO/IEC 646 (IRV), as well as selected control characters.

Byte compaction mode permits all 256 possible 8-bit byte values to be encoded. This includes all ASCII characters value 0 to 127 inclusive and provides for international character set support.

Numeric Compaction mode permits efficient encoding of numeric data strings.

Various function codewords for control purposes.

nSymbol character structure:

Each PDF417 symbol consist of a stack of vertically aligned rows with a minimum of 3 rows (maximum 90 rows). Each row shall include a minimum of a 1 symbol character (maximum 30 symbol characters), excluding start, stop and row indicator columns. The symbol shall include a quiet zone on all four sides. Each character is 17 modules wide: 4 bar and 4 space elements with the largest element 6 module wide. SE450 specifies each module is 2 dots line wide.

nMaximum possible number of data characters per symbol (at error correction level 0):

925 data codewords which can encode:

Text Compaction mode: 1850 characters (at 2 data characters per codeword).

Byte Compaction mode: 1108 characters (at 1.2 data characters per codeword).

Numeric Compaction mode: 2528 characters (at 2.93 data characters per codeword). At the minimum recommended error correction level, there is a maximum of 863 data codewords which can encode:

Text Compaction mode: 1726 characters (at 2 data characters per codeword).

Byte Compaction mode: 1033 characters (at 1.2 data characters per codeword).

39

Image 45
Contents Technical Reference Copyright Contents Page Character Codes Configuration Menu Printer Specifications This page intentionally left blank for double-sided printing Introduction This page intentionally left blank for double-sided printing RS-232 Settings Configuring the Host Computer for RS-232 Serial InterfaceRS-232 Cabling RS-232 Signal LevelsProgramming the LabelWriter Printer Programming OverviewCommand Parameters Resetting the PrinterCharacter Evaluation Bit Character ParametersConversions Font Specifications ObjectsPrint Modes Orientation Raster ModeText Objects Landscape ModeBarcode Objects Line Objects Graphic ObjectsAlphabetical Command List Command ReferenceESC L Position Control Commands by FunctionGS DC2 GS DC3 GS RS GS US Font ControlBarcodes MiscellaneousPrintable Characters Commands Raster Compatibility20h FFh Printable Characters CR Carriage Return DC4 Cancel Double Wide ModeESC a Return Printer Status ESC a Return Hardware StatusESC B Set Dot Tab ESC c Set Print Temperature to Low ESC d Set Print Temperature to MediumESC D Set Bytes per Line ESC E Form Feed ESC e Set Print Temperature to DefaultESC F 1 n Feed n Lines ESC g Set Print Temperature to HighESC h Set Print Speed to Fast ESC i Set Printing Speed to BarcodeESC M Set Font to 12 cpi ESC L Set Feed LengthESC P Set Font to 16 cpi ESC Q Set Top Margin ESC S Set Font to 20 cpiESC T Set Font to 7 cpi ESC U Set Font to 10 cpi ESC W Wrap Data ESC V Return Firmware RevisionESC Y Set Vertical Starting Position ESC X Set Horizontal Starting PositionESC @ Reset to Power-up Condition ESC * Reset to DefaultsESC y Set 203 x 203 dpi ESC z Set 136 x 203 dpiETB Raster Mode Compressed Graphics FF Form Feed GS DC2 Set Font to Double Height GS a Starting Position of Bar CodeGS d Feed n Text Lines GS DC3 Cancel Double HeightGS k Print Barcode GS h Set Barcode HeightUPC-A Data Matrix BarcodeSupported Square Data Matrix Symbol Sizes Supported Rectangular Data Matrix Symbol Sizes Commands Command Reference GS l Draw Line in Landscape Mode Least significant byte of the line length in dots GS L Set Feed Length GS q Print UPC/EAN Checksum GS RS Set Inverse Print ModeReturns GS S Return Printer StatusGS t Set Characters per Line in Landscape GS T Select Line Wrap/Truncate ModesGS u Set Characters per Line in Portrait GS US Cancel Inverse Print ModeGS W Set Bar Code Element Width GS V Set Print OrientationGS w Set Barcode Module Width GS ~ Enter Debug ModeGS * Landscape Mode Graphics SO Set Font to Double Wide Mode HT Horizontal TabLF Line Feed SYN Raster Mode Graphics Caret Feature Activating the Caret FeatureUsing the Caret Feature Command Reference Char Character CodesCharacter Codes CharName \ back slash DEL Name Decimal Hex Binary Caret Feature Character Codes 251 1111 252 253 254 255 This page intentionally left blank for double-sided printing Configuration Menu Configuration Menu Hardware Specifications Printer SpecificationsInterface Specifications Print Head SpecificationsPrinter Specifications Serial Interface Specifications USB SettingsThis page intentionally left blank for double-sided printing