Epson SE450 manual Character Codes

Page 61

The Caret Feature

Character Codes

Below is a list showing the ASCII codes from 1 to 255. The list shows the ASCII characters and names, and the corresponding decimal, hexadecimal, and binary values.

Char	Name
None	NUL
^A	SCH
^B	STX
^C	ETX
^D	EOT
^E	ENQ
^F	ACK
^G	BEL
^H	BS
^I	HT
^J	LF
^K	VT
^L	FF
^M	CR
^N	SO
^O	SI
^P	DLE
^Q	DC1
^R	DC2
^S	DC3
^T	DC4
^U	NAK
^V	SYN
^W	ETB
^X	CAN
^Y	EM
^Z	SUB

Decimal	Hex	Binary
0	00	0000 0000
1	01	0000 0001
2	02	0000 0010
3	03	0000 0011
4	04	0000 0100
5	05	0000 0101
6	06	0000 0110
7	07	0000 0111
8	08	0000 1000
9	09	0000 1001
10	0A	0000 1010
11	0B	0000 1011
12	0C	0000 1100
13	0D	0000 1101
14	0E	0000 1110
15	OF	0000 1111
16	10	0001 0000
17	11	0001 0001
18	12	0001 0010
19	13	0001 0011
20	14	0001 0100
21	15	0001 0101
22	16	0001 0110
23	17	0001 0111
24	18	0001 1000
25	19	0001 1001
26	1A	0001 1010

55

Image 61

Contents Technical Reference Copyright Contents Page Character Codes Configuration Menu Printer Specifications This page intentionally left blank for double-sided printing Introduction This page intentionally left blank for double-sided printing RS-232 Settings Configuring the Host Computer for RS-232 Serial InterfaceRS-232 Cabling RS-232 Signal LevelsProgramming the LabelWriter Printer Programming OverviewCommand Parameters Resetting the PrinterCharacter Evaluation Bit Character ParametersConversions Objects Font SpecificationsPrint Modes Orientation Raster ModeText Objects Landscape ModeBarcode Objects Line Objects Graphic ObjectsAlphabetical Command List Command ReferenceESC L Position Control Commands by FunctionGS DC2 GS DC3 GS RS GS US Font ControlMiscellaneous BarcodesPrintable Characters Raster Compatibility Commands20h FFh Printable Characters CR Carriage Return DC4 Cancel Double Wide ModeESC a Return Hardware Status ESC a Return Printer StatusESC B Set Dot Tab ESC d Set Print Temperature to Medium ESC c Set Print Temperature to LowESC D Set Bytes per Line ESC E Form Feed ESC e Set Print Temperature to DefaultESC F 1 n Feed n Lines ESC g Set Print Temperature to HighESC h Set Print Speed to Fast ESC i Set Printing Speed to BarcodeESC M Set Font to 12 cpi ESC L Set Feed LengthESC P Set Font to 16 cpi ESC S Set Font to 20 cpi ESC Q Set Top MarginESC T Set Font to 7 cpi ESC U Set Font to 10 cpi ESC W Wrap Data ESC V Return Firmware RevisionESC Y Set Vertical Starting Position ESC X Set Horizontal Starting PositionESC @ Reset to Power-up Condition ESC * Reset to DefaultsESC y Set 203 x 203 dpi ESC z Set 136 x 203 dpiETB Raster Mode Compressed Graphics FF Form Feed GS DC2 Set Font to Double Height GS a Starting Position of Bar CodeGS d Feed n Text Lines GS DC3 Cancel Double HeightGS k Print Barcode GS h Set Barcode HeightUPC-A Data Matrix BarcodeSupported Square Data Matrix Symbol Sizes Supported Rectangular Data Matrix Symbol Sizes Commands Command Reference GS l Draw Line in Landscape Mode Least significant byte of the line length in dots GS L Set Feed Length GS q Print UPC/EAN Checksum GS RS Set Inverse Print ModeReturns GS S Return Printer StatusGS t Set Characters per Line in Landscape GS T Select Line Wrap/Truncate ModesGS u Set Characters per Line in Portrait GS US Cancel Inverse Print ModeGS W Set Bar Code Element Width GS V Set Print OrientationGS w Set Barcode Module Width GS ~ Enter Debug ModeGS * Landscape Mode Graphics HT Horizontal Tab SO Set Font to Double Wide ModeLF Line Feed SYN Raster Mode Graphics Activating the Caret Feature Caret FeatureUsing the Caret Feature Command Reference Char Character CodesCharacter Codes CharName \ back slash DEL Name Decimal Hex Binary Caret Feature Character Codes 251 1111 252 253 254 255 This page intentionally left blank for double-sided printing Configuration Menu Configuration Menu Hardware Specifications Printer SpecificationsInterface Specifications Print Head SpecificationsPrinter Specifications Serial Interface Specifications USB SettingsThis page intentionally left blank for double-sided printing