Epson SE450 manual Character Codes Configuration Menu Printer Specifications

Page 5

PDF417 2D Barcode	39
GS l Draw Line in Landscape Mode	41
GS L Set Feed Length	43
GS q Print UPC/EAN Checksum	44
GS RS Set Inverse Print Mode	44
GS S Return Printer Status	45
GS T Select Line Wrap/Truncate Modes	46
GS t Set Characters per Line in Landscape	46
GS US Cancel Inverse Print Mode	47
GS u Set Characters per Line in Portrait	47
GS V Set Print Orientation	48
GS W Set Bar Code Element Width	48
GS w Set Barcode Module Width	49
GS ~ Enter Debug Mode	49
GS * Landscape Mode Graphics	50
HT Horizontal Tab	51
LF Line Feed	51
SO Set Font to Double Wide Mode	51
SYN Raster Mode Graphics	52
The Caret Feature	53
Activating the Caret Feature	53
Using the Caret Feature	53

Character Codes	55
Configuration Menu	65
Printer Specifications	67
Hardware Specifications	67
Interface Specifications	67
Print Head Specifications	67
USB Settings	69
Serial Interface Specifications	69

v

Image 5

Contents Technical Reference Copyright Contents Page Character Codes Configuration Menu Printer Specifications This page intentionally left blank for double-sided printing Introduction This page intentionally left blank for double-sided printing RS-232 Settings Configuring the Host Computer for RS-232 Serial InterfaceRS-232 Cabling RS-232 Signal LevelsProgramming the LabelWriter Printer Programming OverviewCommand Parameters Resetting the PrinterCharacter Evaluation Bit Character ParametersConversions Print Modes Font SpecificationsObjects Orientation Raster ModeText Objects Landscape ModeBarcode Objects Line Objects Graphic ObjectsAlphabetical Command List Command ReferenceESC L Position Control Commands by FunctionGS DC2 GS DC3 GS RS GS US Font ControlPrintable Characters BarcodesMiscellaneous 20h FFh Printable Characters CommandsRaster Compatibility CR Carriage Return DC4 Cancel Double Wide ModeESC B Set Dot Tab ESC a Return Printer StatusESC a Return Hardware Status ESC D Set Bytes per Line ESC c Set Print Temperature to LowESC d Set Print Temperature to Medium ESC E Form Feed ESC e Set Print Temperature to DefaultESC F 1 n Feed n Lines ESC g Set Print Temperature to HighESC h Set Print Speed to Fast ESC i Set Printing Speed to BarcodeESC M Set Font to 12 cpi ESC L Set Feed LengthESC P Set Font to 16 cpi ESC T Set Font to 7 cpi ESC Q Set Top MarginESC S Set Font to 20 cpi ESC U Set Font to 10 cpi ESC W Wrap Data ESC V Return Firmware RevisionESC Y Set Vertical Starting Position ESC X Set Horizontal Starting PositionESC @ Reset to Power-up Condition ESC * Reset to DefaultsESC y Set 203 x 203 dpi ESC z Set 136 x 203 dpiETB Raster Mode Compressed Graphics FF Form Feed GS DC2 Set Font to Double Height GS a Starting Position of Bar CodeGS d Feed n Text Lines GS DC3 Cancel Double HeightGS k Print Barcode GS h Set Barcode HeightUPC-A Data Matrix BarcodeSupported Square Data Matrix Symbol Sizes Supported Rectangular Data Matrix Symbol Sizes Commands Command Reference GS l Draw Line in Landscape Mode Least significant byte of the line length in dots GS L Set Feed Length GS q Print UPC/EAN Checksum GS RS Set Inverse Print ModeReturns GS S Return Printer StatusGS t Set Characters per Line in Landscape GS T Select Line Wrap/Truncate ModesGS u Set Characters per Line in Portrait GS US Cancel Inverse Print ModeGS W Set Bar Code Element Width GS V Set Print OrientationGS w Set Barcode Module Width GS ~ Enter Debug ModeGS * Landscape Mode Graphics LF Line Feed SO Set Font to Double Wide ModeHT Horizontal Tab SYN Raster Mode Graphics Using the Caret Feature Caret FeatureActivating the Caret Feature Command Reference Char Character CodesCharacter Codes CharName \ back slash DEL Name Decimal Hex Binary Caret Feature Character Codes 251 1111 252 253 254 255 This page intentionally left blank for double-sided printing Configuration Menu Configuration Menu Hardware Specifications Printer SpecificationsInterface Specifications Print Head SpecificationsPrinter Specifications Serial Interface Specifications USB SettingsThis page intentionally left blank for double-sided printing