Transcend Information TS2GCF133 Multiple Sector Setting, Total Sectors Addressable in LBA Mode

Page 62

TS1G~32GCF133

133X CompactFlash Card

 

 

 

Multiple Sector Setting

Bits 15-9 are reserved and shall be set to 0.

Bit 8 shall be set to 1 indicating that the Multiple Sector Setting is valid.

Bits 7-0 are the current setting for the number of sectors that shall be transferred per interrupt on Read/Write Multiple commands.

Total Sectors Addressable in LBA Mode

This field contains the total number of user addressable sectors for the CompactFlash Storage Card in LBA mode only.

Multiword DMA transfer

Bits 15 through 8 of word 63 of the Identify Device parameter information is defined as the Multiword DMA mode selected field. If this field is supported, bit 1 of word 53 shall be set to one. This field is bit significant. Only one of bits may be set to one in this field by the CompactFlash Storage Card to indicate the multiword DMA mode which is currently selected. Of these bits, bits 15 through 11 are reserved. Bit 8, if set to one, indicates that Multiword DMA mode 0 has been selected. Bit 9, if set to one, indicates that Multiword DMA mode 1 has been selected. Bit 10, if set to one, indicates that Multiword DMA mode 2 has been selected.

Selection of Multiword DMA modes 3 and above are specific to CompactFlash are reported in word 163, Word 163: CF Advanced True IDE Timing Mode Capabilities and Settings.

Bits 7 through 0 of word 63 of the Identify Device parameter information is defined as the Multiword DMA data transfer supported field. If this field is supported, bit 1 of word 53 shall be set to one. This field is bit significant. Any number of bits may be set to one in this field by the CompactFlash Storage Card to indicate the Multiword DMA modes it is capable of supporting.

Of these bits, bits 7 through 2 are reserved. Bit 0, if set to one, indicates that the CompactFlash Storage Card supports Multiword DMA mode 0. Bit 1, if set to one, indicates that the CompactFlash Storage Card supports Multiword DMA modes 1 and 0. Bit 2, if set to one, indicates that the CompactFlash Storage Card supports Multiword DMA modes 2, 1 and 0. Support for Multiword DMA modes 3 and above are specific to CompactFlash are reported in word 163, Word 163: CF Advanced True IDE Timing Mode Capabilities and Settings.

Word 64: Advanced PIO transfer modes supported

Bits 7 through 0 of word 64 of the Identify Device parameter information is defined as the advanced PIO data transfer supported field. If this field is supported, bit 1 of word 53 shall be set to one. This field is bit significant. Any number of bits may be set to one in this field by the CompactFlash Storage Card to indicate the advanced PIO modes it is capable of supporting.

Of these bits, bits 7 through 2 are reserved. Bit 0, if set to one, indicates that the CompactFlash Storage Card supports PIO mode 3. Bit 1, if set to one, indicates that the CompactFlash StorageCard supports PIO mode 4.

Support for PIO modes 5 and above are specific to CompactFlash are reported in word 163.

Word 65: Minimum Multiword DMA transfer cycle time

Word 65 of the parameter information of the Identify Device command is defined as the minimum Multiword DMA transfer cycle time. This field defines, in nanoseconds, the minimum cycle time that, if used by the host, the CompactFlash Storage Card guarantees data integrity during the transfer.

If this field is supported, bit 1 of word 53 shall be set to one. The value in word 65 shall not be less than the minimum cycle time for the fastest DMA mode supported by the device. This field shall be supported by all CompactFlash Storage Cards supporting DMA modes 1 and above. If bit 1 of word 53 is set to one, but this field is not supported, the Card shall return a value of zero in this field.

Recommended Multiword DMA transfer cycle time

Word 66 of the parameter information of the Identify Device command is defined as the recommended Multiword DMA transfer cycle time. This field defines, in nanoseconds, the cycle time that, if used by the host, may optimize the data transfer from by reducing the probability that the CompactFlash Storage Card

Transcend Information Inc.

62

Page 61 Page 63
Image 62
Page 61 Page 63
Contents 133X CompactFlash Card Placement FeaturesDimensions DescriptionTranscend Block Diagram Pin Assignments and Pin Type TS1G~32GCF133 Signal Description DirGND Inpack Iowr VCC Wait Electrical Specification Output Drive Type Output Drive Characteristics Signal Interface Additional Requirements for CF Advanced Timing Modes Resistor is optionalSeries termination required for Ultra DMA operation 133X CompactFlash CardUltra DMA Electrical Requirements Table Typical Series Termination for Ultra DMAUltra DMA Mode Cabling Requirement Attribute Memory Read Timing Specification TS1G~32GCF133133X CompactFlash Card Common Memory Read Timing Specification Common Memory Write Timing Specification Input Read Timing Specification TS1G~32GCF133 Output Write Timing Specification TS1G~32GCF133 True IDE PIO Mode Read/Write Timing Specification TS1G~32GCF133 True IDE Ultra DMA Mode Read/Write Timing Specification Table Ultra DMA Data Burst Timing133X CompactFlash Card TS1G~32GCF133 TS1G~32GCF133 TS1G~32GCF133 Card Configuration Multiple Function CompactFlash Storage CardsAttribute Memory Function Attribute Memory FunctionConfiguration Option Register Base + 00h in Attribute Memory TS1G~32GCF133 Pin Replacement Register Base + 04h in Attribute Memory Socket and Copy Register Base + 06h in Attribute Memory Table Pcmcia Mode I/O Function Transfer FunctionCommon Memory Transfer Function Table Common Memory FunctionTrue IDE Mode I/O Transfer Function Metaformat Overview CF-ATA Drive Register Set Definition and Protocol Primary and Secondary Address Configurations Table Primary and Secondary I/O DecodingContiguous I/O Mapped Addressing Table Contiguous I/O DecodingTrue IDE Mode Addressing Memory Mapped AddressingCF-ATA Registers Data Register Address 1F0h170hOffset 0,8,9Sector Number LBA 7-0 Register Address 1F3h173h Offset Feature Register Address 1F1h171h Offset 1, 0Dh Write OnlySector Count Register Address 1F2h172h Offset Cylinder Low LBA 15-8 Register Address 1F4h174h OffsetTS1G~32GCF133 Device Control Register Address 3F6h376h Offset Eh Card Drive Address Register Address 3F7h377h Offset Fh CF-ATA Command Set LBADefinitions Check Power Mode 98h or E5h Execute Drive Diagnostic 90h Erase Sectors C0hFlush Cache E7h Format Track 50hIdentify Device Ech Data Field Type InformationTS1G~32GCF133 0X00h Word 3 Default Number of Heads Word 0 General ConfigurationWord 1 Default Number of Cylinders Word 6 Default Number of Sectors per TrackWords 10-19 Serial Number PIO Data Transfer Cycle Timing ModeWords 7-8 Number of Sectors per Card Word 22 ECC CountMultiword DMA transfer Multiple Sector SettingTotal Sectors Addressable in LBA Mode Word 64 Advanced PIO transfer modes supportedWords 82-84 Features/command sets supported Word 68 Minimum PIO transfer cycle time with IordyWords 85-87 Features/command sets enabled Word 88 Ultra DMA Modes Supported and SelectedWord 89 Time required for Security erase unit completion Word 91 Advanced power management level valueWord 160 Power Requirement Description Word 128 Security StatusValue Current PIO timing mode selected Value Maximum PIO mode timing selectedValue Maximum Multiword DMA timing mode supported Word 162 Key Management Schemes SupportedValue Maximum Memory timing mode Supported Value Current Multiword DMA timing mode selectedValue Maximum Pcmcia IO timing mode Supported Idle 97h or E3hNOP 00h Idle Immediate 95h or E1hInitialize Drive Parameters 91h Read Buffer E4h Read DMA C8h Read Long Sector 22h or 23hTS1G~32GCF133 Seek 7Xh Set Features EFh Feature Supported133X CompactFlash Card TS1G~32GCF133 Standby Immediate 94h or E0h Translate Sector 87h Translate Sector InformationWear Level F5h Write Buffer E8h Write DMA CAh TS1G~32GCF133 TS1G~32GCF133 Error Posting Smart Command Set Smart Command Set Smart Feature Register ValuesSmart Data Structure Decription
Top Page Image Contents