MGE UPS Systems Switched PDU System Administration, Operations, Creating a location description

Page 37

3. Operations

System Administration

Creating a location description

The Set Location command specifies text that appears in the HTML control screen’s Location field. The text is also appended to a Welcome to banner that appears when a user successfully logs in serially or through a Telnet session.

If you do not issue this command, or if you issue this command without specifying any text, the control screen ’s Location field will be blank and no Welcome to banner will be displayed.

To create a location description:

At the Switched PDU: prompt, type set location, followed by a descriptive name of up to 24 alphanumeric and other typeable characters (ASCII 32 to 126 decimal - spaces are allowed). Press Enter.

Omitting any characters after typing ‘set location’ deletes any previously specified text.

Examples

The following command specifies Florida HQ as the descriptive location for the control screen and the login banner:

Switched PDU: set location Florida HQ<Enter>

The following command deletes any previously specified location description:

Switched PDU: set location<Enter>

In this case, the control screen’s Location field will be blank, and no welcome banner will be displayed after a successful login.

Displaying system configuration information

The Show System command displays all system configuration information.

•Firmware version

•NIC module serial number and MAC address

•Hardware revision code and Flash size

•Uptime since last system restart

•System location description

To display system configuration information:

At the Switched PDU: prompt, type show system and press Enter.

Example

System	Information
F/W	Version:	Switched PDU Version 5.3a
NIC	S/N:	1600001
MAC	Address:	00-0a-9c-10-00-01
H/W	Rev Code:	0	MB
Flash Size:		1
Uptime:		0	days 6 hours 14 minutes 1 second
Location:		Florida HQ

301-0399-4 Rev A. - Page 37

Image 37

Contents E T N I N U E H T Switched PDU Installation and user manualDangerous Voltage InstructionsProtective Grounding Terminal Life-Support PolicyINSTALLATION ContentsGETTING STARTED OPERATIONSQuick Start Guide 1. Getting Starteduser account prior to attachment to your network Standard Accessories 2. InstallationAdditional Required Items Figure 1. Unit Views Equipment Overview1 Power Input 2 Input Current LED 3 Ethernet / RS232 Ports 4 Temperature / Humidity PortsInstalling the Power Input Retention Bracket Safety PrecautionsFigure 2. Retention Bracket assembly To install the power input retention bracketTo attach a power cord to the unit Connecting to the Power SourceTo connect to the power source MountingConnecting the Sensors Connecting DevicesConnecting to the Unit Serial RS232 portPage I NTERFACES 3. OperationsHTML I NTERFACE C OMMAND L INE I NTERFACE3. Operations Usernames and PasswordsInterfaces Outlet Naming and GroupingFigure 4. Example HTML page Logging In HTML InterfaceTo log in by HTML Individual Outlet ControlGroup Outlet State/Control State Field ValuesEnvironmental Monitoring ConfigurationInput Load SensorsTelnet/SSH NetworkHTTP/SSL Setting the IP address, subnet mask or gatewaySetting the HTTP authentication method Serial PortsSetting SSL access level Setting the data-rate for the serial portsGroups OutletsUsers Changing a user passwordAdding and Deleting outlet access Changing a user’s access privilege levelAdding and Deleting group access Adding and Deleting serial port accessSNMP SNTPSetting the filename for upload Testing the FTP upload configurationTools Command Line InterfaceRestart Logging InAdministrative Command Summary Operations Command SummaryAdministrative Command Summary continued To display the names of commands that you may executeRebooting outlets Operations CommandsTo reboot one or more outlets Turning outlets onTo display on/off status of one or more outlets Displaying outlet statusTo display accessible outlets Displaying accessible outletsDisplaying accessible groups To display accessible groupsTo display accessible serial ports Displaying accessible serial portsConnecting to a serial device Displaying infeed statusTo display the status of the Environmental Monitor Displaying the status of the Environmental MonitorStarting a new session To start a new sessionUser Administration Administration CommandsCreating a user account To create a user accountTo change a password Changing a passwordSetting user access level privileges To set the access level privilege for a userTo display user access privilege levels Displaying the access privilege levelsAdding outlet access to a user To grant outlet access to a userTo delete outlet access for a user Deleting outlet access for a userAdding group access to a user To grant group access to a userDisplaying user outlet, group and serial port access Group AdministrationTo display user outlet, group and serial port access Creating a group nameAdding an outlet to a group Outlet AdministrationTo add an outlet to a group Deleting an outlet from a groupTo set the wakeup state Setting the outlet wakeup stateDisplaying outlet information To display outlet informationSetting the serial ports data-rate Serial Port AdministrationEnabling or disabling active signal checking for serial connections To enable or disable active signal checking for serial connectionsDisplaying system configuration information System AdministrationTo display system configuration information Creating a location descriptionTo create a tower name Creating a descriptive tower nameDisplaying tower information To display tower informationTo perform a warm boot TCP/IP AdministrationSetting the IP address Setting the subnet maskDisplaying network configuration information HTTP AdministrationTo display network configuration information To enable or disable HTTP supportFTP Administration Telnet AdministrationTo set the HTTP authentication method To enable or disable Telnet supportTo set the FTP password Setting the FTP PasswordSetting the filename to be uploaded Setting the filepath for the file to be uploadedSetting the SNTP server address SNTP AdministrationDisplaying SNTP configuration information To display SNTP configuration informationSSL Technical Specifications Enabling and Setting up SSL SupportEnabling and Setting up SSH Support SSH Technical SpecificationsEnabling and Setting up SSL Support SSL Command SummarySSL Technical Specifications To enable or disable SSL supportEnabling and Setting up SSH Support SSH Command SummarySSH Technical Specifications To enable or disable SSH supportEnabling and Setting up SNMP Support SNMP Command SummarySNMP To enable SNMP supportTo set the trap timer To reset the trap destinationSetting the Get/Set community strings Setting the Trap community stringTrap Summary SNMP TrapsTower Status traps Infeed Status trapsEnvironmental Monitor Status traps Outlet Status trapsTemperature/Humidity Sensor Status traps Load trapsHumidity traps Temp trapsTemp Trap Humidity TrapTo Enable or Disable a Status trap Configuring Traps SNMP Trap Command SummaryEnabling or Disabling a Status trap Setting the Infeed Load limit To Enable or Disable a Load trapTo Enable or Disable a Change trap To Enable or Disable the Temp trapTo Enable or Disable the Humid trap Setting the Temperature sensor threshold limitsSetting the Humidity sensor threshold limits To set the Temperature threshold limitsTo display trap information Displaying trap configuration informationStatus WebServer15. Appendices R ESETTING TO F ACTORY D EFAULTSU PLOADING F IRMWARE T ECHNICAL S PECIFICATIONSTo reset to factory defaults from the HTML interface Resetting to Factory DefaultsTo reset to factory defaults from the command line To reset to factory defaults using the reset buttonPower Ratings Technical SpecificationsPhysical Specifications Models Europe/AsiaData Connections LED IndicatorsBranch Circuit Protection RS-232 portPage