MGE UPS Systems Switched PDU Operations, Changing a password, To change a password, Examples

Page 30

Changing a password

3. Operations

Changing a password

The Set User Password command changes a user’s password. For security, when you type a password, the characters are not displayed on the screen. See Usernames and Passwords for more information.

To change a password:

At the Switched PDU: prompt, type set user password, followed by a username and press Enter.

At the Password: prompt, type the new password and press Enter. Passwords may contain up to 16 characters, and spaces are not allowed. To specify no password, press Enter at the prompt.

At the Verify Password: prompt, retype the new password and press Enter. To verify no password, press Enter at the prompt.

Examples

The following command changes the password for the user JohnDoe:

Switched PDU: set user password johndoe<Enter>

Password: <Enter>

Verify Password: <Enter>

The following command blanks the password for the user JaneDoe:

Switched PDU: set user password<Enter>

Username: janedoe<Enter>

Password: <Enter>

Verify Password: <Enter>

Setting user access level privileges

The Set User Access command sets the access level privileges for a user. The Switched PDU has four defined access privilege levels; Admin, User, On-Only and View-Only. For more information on user access levels, see Changing a user’s access privilege level: on page 19.

The administrator may also grant administrative privileges to other user accounts allowing the Switched PDU to have more than one administrative-level user.

NOTE: You cannot remove administrative privileges from the Admn user unless another user has already been given administrative access level privileges created.

To set the access level privilege for a user:

At the Switched PDU: prompt, type set user access, followed by admin, user, ononly or viewonly, optionally followed by a username and press Enter.

Examples

The following command sets the user access level for JohnDoe to Admin:

Switched PDU: set user access admin johndoe<Enter>

The following command sets the user access level for JaneDoe to User:

Switched PDU: set user access user janedoe<Enter>

Page 30 - 301-0399-4 Rev A.

Image 30

Contents Switched PDU Installation and user manual E T N I N U E H TProtective Grounding Terminal InstructionsDangerous Voltage Life-Support PolicyGETTING STARTED ContentsINSTALLATION OPERATIONS1. Getting Started Quick Start Guideuser account prior to attachment to your network 2. Installation Standard AccessoriesAdditional Required Items 1 Power Input 2 Input Current LED 3 Ethernet / RS232 Ports Equipment OverviewFigure 1. Unit Views 4 Temperature / Humidity PortsFigure 2. Retention Bracket assembly Safety PrecautionsInstalling the Power Input Retention Bracket To install the power input retention bracketTo connect to the power source Connecting to the Power SourceTo attach a power cord to the unit MountingConnecting to the Unit Connecting DevicesConnecting the Sensors Serial RS232 portPage HTML I NTERFACE 3. OperationsI NTERFACES C OMMAND L INE I NTERFACEInterfaces Usernames and Passwords3. Operations Outlet Naming and GroupingHTML Interface Figure 4. Example HTML page Logging InTo log in by HTML Group Outlet ControlIndividual Outlet State/Control State Field ValuesInput Load ConfigurationEnvironmental Monitoring SensorsHTTP/SSL NetworkTelnet/SSH Setting the IP address, subnet mask or gatewaySetting SSL access level Serial PortsSetting the HTTP authentication method Setting the data-rate for the serial portsUsers OutletsGroups Changing a user passwordAdding and Deleting group access Changing a user’s access privilege levelAdding and Deleting outlet access Adding and Deleting serial port accessSetting the filename for upload SNTPSNMP Testing the FTP upload configurationRestart Command Line InterfaceTools Logging InOperations Command Summary Administrative Command SummaryTo display the names of commands that you may execute Administrative Command Summary continuedTo reboot one or more outlets Operations CommandsRebooting outlets Turning outlets onDisplaying outlet status To display on/off status of one or more outletsDisplaying accessible groups Displaying accessible outletsTo display accessible outlets To display accessible groupsConnecting to a serial device Displaying accessible serial portsTo display accessible serial ports Displaying infeed statusStarting a new session Displaying the status of the Environmental MonitorTo display the status of the Environmental Monitor To start a new sessionCreating a user account Administration CommandsUser Administration To create a user accountSetting user access level privileges Changing a passwordTo change a password To set the access level privilege for a userAdding outlet access to a user Displaying the access privilege levelsTo display user access privilege levels To grant outlet access to a userAdding group access to a user Deleting outlet access for a userTo delete outlet access for a user To grant group access to a userTo display user outlet, group and serial port access Group AdministrationDisplaying user outlet, group and serial port access Creating a group nameTo add an outlet to a group Outlet AdministrationAdding an outlet to a group Deleting an outlet from a groupDisplaying outlet information Setting the outlet wakeup stateTo set the wakeup state To display outlet informationEnabling or disabling active signal checking for serial connections Serial Port AdministrationSetting the serial ports data-rate To enable or disable active signal checking for serial connectionsTo display system configuration information System AdministrationDisplaying system configuration information Creating a location descriptionDisplaying tower information Creating a descriptive tower nameTo create a tower name To display tower informationSetting the IP address TCP/IP AdministrationTo perform a warm boot Setting the subnet maskTo display network configuration information HTTP AdministrationDisplaying network configuration information To enable or disable HTTP supportTo set the HTTP authentication method Telnet AdministrationFTP Administration To enable or disable Telnet supportSetting the filename to be uploaded Setting the FTP PasswordTo set the FTP password Setting the filepath for the file to be uploadedDisplaying SNTP configuration information SNTP AdministrationSetting the SNTP server address To display SNTP configuration informationEnabling and Setting up SSH Support Enabling and Setting up SSL SupportSSL Technical Specifications SSH Technical SpecificationsSSL Technical Specifications SSL Command SummaryEnabling and Setting up SSL Support To enable or disable SSL supportSSH Technical Specifications SSH Command SummaryEnabling and Setting up SSH Support To enable or disable SSH supportSNMP SNMP Command SummaryEnabling and Setting up SNMP Support To enable SNMP supportSetting the Get/Set community strings To reset the trap destinationTo set the trap timer Setting the Trap community stringTower Status traps SNMP TrapsTrap Summary Infeed Status trapsTemperature/Humidity Sensor Status traps Outlet Status trapsEnvironmental Monitor Status traps Load trapsTemp Trap Temp trapsHumidity traps Humidity TrapConfiguring Traps SNMP Trap Command Summary To Enable or Disable a Status trapEnabling or Disabling a Status trap To Enable or Disable a Change trap To Enable or Disable a Load trapSetting the Infeed Load limit To Enable or Disable the Temp trapSetting the Humidity sensor threshold limits Setting the Temperature sensor threshold limitsTo Enable or Disable the Humid trap To set the Temperature threshold limitsStatus Displaying trap configuration informationTo display trap information WebServer1U PLOADING F IRMWARE R ESETTING TO F ACTORY D EFAULTS5. Appendices T ECHNICAL S PECIFICATIONSTo reset to factory defaults from the command line Resetting to Factory DefaultsTo reset to factory defaults from the HTML interface To reset to factory defaults using the reset buttonPhysical Specifications Technical SpecificationsPower Ratings Models Europe/AsiaBranch Circuit Protection LED IndicatorsData Connections RS-232 portPage