SEAL 6500 owner manual Speed Adjustment Knob, Reverse Roller Direction Switch, Motor Stop Switch

Page 15

T O P M O T O R C O N T R O L PA N E L S

The Motor Control Panels are centrally located on the top of both side cabinets. This location provides easy access from all sides of the laminator. Right- or left-handed operators can use either panel to make speed or direction processing adjustments from the front or rear of the laminator. A change made to either panel affects the settings of both panels.

1. Speed Adjustment Knob

Use this knob to adjust the speed of the roller rotation. Turn the knob clockwise to increase the speed of the roller rotation and counter-clockwise to decrease the speed. The speed of the rollers is continuously adjustable between 0 and 15 ft./min. (0 and 4.5m/min.). The roller speed can be viewed in the top display readouts on both the front and back control panels.

2. Reverse Roller Direction Switch

Pressing this switch runs the rollers in the reverse direction when standing at the front of the laminator. This direction will be used when processing cold pressure-sensitive films from the rear of the laminator through the pull rollers.

3. Motor Stop Switch

Pressing this switch stops the roller rotation.

NOTE: You must press this switch before you can press the opposite direction switch.

4. Forward Roller Direction Switch

Pressing this switch runs the rollers in the forward direc- tion when standing at the front of the laminator.

Figure 8. Top Motor Control Panel

15

Image 15

Contents Image 6500 Laminator Page T R O D U C T I O N Statement of Intended USEE C T R I C a L S P E C I F I C AT I O N S Connecting Your LaminatorR K S PA C E R E Q U I R E M E N T S MediaWater and Moisture Ambient TemperaturePower Supply Relative HumidityPA C K I N G , S E T- U P a N D I N S TA L L AT I O N Accessories IncludedLeveling Your Laminator Unpacking Your LaminatorElectrical Parts Danger of being injured by electricity Servicing and Replacement PartsRotating Parts Risk of Injury Hot Surface Risk of Injury on ContactDoor Interlock F E T Y F E AT U R E SM I N AT O R F E AT U R E S FeaturesFront Control Panel O N T C O N T R O L PA N E LBack Control Panel C K C O N T R O L PA N E LAIR Pressure Gauge AIR Regulator KnobU T C H C O N T R O L PA N E L Forward Roller Direction Switch Speed Adjustment KnobReverse Roller Direction Switch Motor Stop SwitchCheck the Heater Controls Check the Main PowerCheck the Motor and Foot Switches Check the Emergency Stop ButtonsT- U P a N D O P E R AT I O N Temperature SettingsHOW to SET the Shim Wheels Shim Wheel SettingsLoading a Roll of Material Unwind shaft cord adjustmentPivoting Roll Easel Bracket Down Pivoting Table USE for WebbingTo insert the cooling tube in the top location Setting the Unwind Brake TensionCooling System To remove the cooling tube from the bottom locationFoot Switch Operation AUTO-RUN OperationRotation of the Rollers will Stop When E D I N G I M a G E S Using the Print Guide TableUsing the Roll Easel Attachment Basic Steps to Feeding ImagesB B I N G F I L M S W I T H O U T a R E L E a S E L I N E R You are now ready to feed imagesB B I N G F I L M S W I T H a R E L E a S E L I N E R YOU are NOW Ready to Feed ImagesFilms Webbing SettingsWebbing for Decaling Pressure-sensitive films Media Ink Jet, Electrostatic, and PhotographicU N T I N G To Mount Decals Onto a SubstrateFront C a P S U L AT I N GE C O AT I N G B O a R D S PreparationWebbing for Vinyl Transfer Media ElectrostaticWebbing Settings Front Control Panel SettingsBack Control Panel Settings Motor Control Panel SettingsE a N I N G / M a I N TA I N I N G Y O U R L a M I N AT O R Cleaning the LaminatorCleaning the Rollers Greasing the BearingsChain Tension Drain Water Adjustment/Oil Chain Air Filter Grease BearingsR I O D I C M a I N T E N a N C E S H E E T Technical Service Problem SolutionLED PA R E PA R T S L I S T Order Codes MechanicalProcess ElectricalM I T E D W a R R a N T Y