SEAL 6500 owner manual O N T C O N T R O L Pa N E L, Front Control Panel

Page 12

F R O N T C O N T R O L PA N E L

1.Air Pressure Gauge: Indicates the PSI reading for the downward pressure of the top main roller. The standard setting for the normal operation is 35-55 PSI.

2.Air Regulator Knob: Adjusts the downward pressure of the top roller. Turn clockwise to increase the pressure.

3.Roller Up/Down Switch (Front, Top): Press up to raise the roller. Press down to lower the roller.

4.Cooling Fan On/Off Button: Turns On/Off the cool- ing fan. The corresponding LED will be lit when the fan is ON.

5.Reset Button: Press this button to reset the material total usage counter to zero. Totalizer Display must be showing to be able to zero out.

6.Ratemeter/Totalizer Button: Pressing this button will toggle between the roller speed readout or total material usage. Press this button to track and display the total number of feet or meters run in a given period, which can help to monitor film usage. The total will be stored even after the laminator is turned off and adds to the total whenever the bottom main roller is turning. The corre- sponding LED will be lit when the totalizer is being used.

7.Ratemeter/Totalizer Readout: Displays the rate of speed of the main rollers in either feet or meters per minute, or displays the total number of feet or meters run in a given period.

8.Top Roller Temperature Increase Button: Press this button once to view the temperature set point. Press and hold the button to raise the top roller temperature.

9.Top Roller Temperature Readout: Displays both the set and actual temperature of the top roller.

10.Top Roller Temperature Decrease Button: Press this button once to view the temperature set point. Press and hold the button to lower the top roller temperature.

11.Bottom Roller Temperature Increase Button: Press this button once to view the temperature set point. Press and hold the button to raise the bottom roller tempera- ture.

12.Bottom Roller Temperature Readout: Displays both the set and actual temperature of the bottom roller.

13.Bottom Roller Temperature Decrease Button: Press this button once to view the temperature set point. Press and hold the button to lower the bottom roller tempera- ture.

14.Bottom Roller Temperature On/Off Button: Turns On/Off the bottom roller heater. The corresponding LED will be lit when the heater is ON.

15.Top Roller Temperature On/Off Button: Turns On/Off the top roller heater. The corresponding LED will be lit when the heater is ON.

16.Stand-By On/Off Switch: Press this switch up to turn on the laminator. Press this switch down to put it on Standby. In Standby, the laminator power is still on, but all functions are disabled.

Figure 5. Front Control Panel

12

Image 12
Contents Image 6500 Laminator Page Statement of Intended USE T R O D U C T I O NConnecting Your Laminator E C T R I C a L S P E C I F I C AT I O N SMedia R K S PA C E R E Q U I R E M E N T SAmbient Temperature Power SupplyRelative Humidity Water and MoistureAccessories Included PA C K I N G , S E T- U P a N D I N S TA L L AT I O NUnpacking Your Laminator Leveling Your LaminatorServicing and Replacement Parts Rotating Parts Risk of InjuryHot Surface Risk of Injury on Contact Electrical Parts Danger of being injured by electricityF E T Y F E AT U R E S Door InterlockFeatures M I N AT O R F E AT U R E SO N T C O N T R O L PA N E L Front Control PanelC K C O N T R O L PA N E L Back Control PanelAIR Pressure Gauge AIR Regulator KnobU T C H C O N T R O L PA N E L Speed Adjustment Knob Reverse Roller Direction SwitchMotor Stop Switch Forward Roller Direction SwitchCheck the Main Power Check the Motor and Foot SwitchesCheck the Emergency Stop Buttons Check the Heater ControlsTemperature Settings HOW to SET the Shim WheelsShim Wheel Settings T- U P a N D O P E R AT I O NUnwind shaft cord adjustment Loading a Roll of MaterialPivoting Table USE for Webbing Pivoting Roll Easel Bracket DownSetting the Unwind Brake Tension Cooling SystemTo remove the cooling tube from the bottom location To insert the cooling tube in the top locationFoot Switch Operation AUTO-RUN OperationRotation of the Rollers will Stop When Using the Print Guide Table Using the Roll Easel AttachmentBasic Steps to Feeding Images E D I N G I M a G E SYou are now ready to feed images B B I N G F I L M S W I T H O U T a R E L E a S E L I N E RYOU are NOW Ready to Feed Images B B I N G F I L M S W I T H a R E L E a S E L I N E RWebbing Settings FilmsMedia Ink Jet, Electrostatic, and Photographic Webbing for Decaling Pressure-sensitive filmsTo Mount Decals Onto a Substrate U N T I N GC a P S U L AT I N G FrontPreparation E C O AT I N G B O a R D SMedia Electrostatic Webbing for Vinyl TransferFront Control Panel Settings Back Control Panel SettingsMotor Control Panel Settings Webbing SettingsCleaning the Laminator Cleaning the RollersGreasing the Bearings E a N I N G / M a I N TA I N I N G Y O U R L a M I N AT O RChain Tension Drain Water Adjustment/Oil Chain Air Filter Grease BearingsR I O D I C M a I N T E N a N C E S H E E T Problem Solution Technical ServiceLED PA R E PA R T S L I S T Mechanical ProcessElectrical Order CodesM I T E D W a R R a N T Y