SEAL 6500 owner manual Unpacking Your Laminator, Leveling Your Laminator

Page 8

U N PA C K I N G , S E T- U P A N D I N S TA L L AT I O N

UNPACKING YOUR LAMINATOR

Remove the transport packing and the plastic shrink- wrap the laminator is wrapped in to avoid moisture penetration.

Remove the accessory kit package from the top of the laminator, which includes the necessary tools for installation.

Remove the foot switches from the top of the laminator and remove the foam wrapped around them. Place a foot switch on each side of the laminator for operator use while feeding images.

Remove the front and back tables (in cardboard boxes) from the top of the laminator. Remove the tables from the cardboard boxes and set them aside.

Remove the protective foam wrapped around the front and back table arms.

Follow the Installation Instruction sheet in the accessory pack to reattach the table arms.

Once reattached, insert the tables into position.

Remove the roll easel shaft from the crate and remove the packing wrap.

Place the roll easel shaft into the table receivers and lock into place.

The top rollers will go up automatically when air is connected.

Remove the foam placed between the top and bottom rollers.

Remove the stickers securing the protective paper on the rolls using your fingers only.

Then gently pull the paper towards you to unwind off the roll.

WARNING! Do not use open blades to remove the protective paper on the rollers.

Roller damage caused by improper use of cutting tools will void the user’s warranty. Small cuts and imperfec- tions in the rollers greatly affect the quality of the output and roller replacement costs are expensive.

LEVELING YOUR LAMINATOR

Thread the leveling feet included in the accessory pack onto each of the four transport bolts located in the corners of the cabinets. Tighten securely.

Use the 1/2" wrench to turn the transport bolts down until the leveling feet are positioned flat against the floor.

Insert a 3' x 1' (91cm x 30cm) piece of foam board across the two center chill idlers and place the level in the center on top of this foam board.

Adjust the leveling feet for each side cabinet until level.

Next, place the level on the tops of each of the cabinets lengthwise and adjust the leveling feet from the front to the rear of the cabinet as needed.

8

Image 8
Contents Image 6500 Laminator Page Statement of Intended USE T R O D U C T I O NConnecting Your Laminator E C T R I C a L S P E C I F I C AT I O N SMedia R K S PA C E R E Q U I R E M E N T SAmbient Temperature Power SupplyRelative Humidity Water and MoistureAccessories Included PA C K I N G , S E T- U P a N D I N S TA L L AT I O NUnpacking Your Laminator Leveling Your LaminatorServicing and Replacement Parts Rotating Parts Risk of InjuryHot Surface Risk of Injury on Contact Electrical Parts Danger of being injured by electricityF E T Y F E AT U R E S Door InterlockFeatures M I N AT O R F E AT U R E SO N T C O N T R O L PA N E L Front Control PanelC K C O N T R O L PA N E L Back Control PanelU T C H C O N T R O L PA N E L AIR Pressure GaugeAIR Regulator Knob Speed Adjustment Knob Reverse Roller Direction SwitchMotor Stop Switch Forward Roller Direction SwitchCheck the Main Power Check the Motor and Foot SwitchesCheck the Emergency Stop Buttons Check the Heater ControlsTemperature Settings HOW to SET the Shim WheelsShim Wheel Settings T- U P a N D O P E R AT I O NUnwind shaft cord adjustment Loading a Roll of MaterialPivoting Table USE for Webbing Pivoting Roll Easel Bracket DownSetting the Unwind Brake Tension Cooling SystemTo remove the cooling tube from the bottom location To insert the cooling tube in the top locationRotation of the Rollers will Stop When Foot Switch OperationAUTO-RUN Operation Using the Print Guide Table Using the Roll Easel AttachmentBasic Steps to Feeding Images E D I N G I M a G E SYou are now ready to feed images B B I N G F I L M S W I T H O U T a R E L E a S E L I N E RYOU are NOW Ready to Feed Images B B I N G F I L M S W I T H a R E L E a S E L I N E RWebbing Settings FilmsMedia Ink Jet, Electrostatic, and Photographic Webbing for Decaling Pressure-sensitive filmsTo Mount Decals Onto a Substrate U N T I N GC a P S U L AT I N G FrontPreparation E C O AT I N G B O a R D SMedia Electrostatic Webbing for Vinyl TransferFront Control Panel Settings Back Control Panel SettingsMotor Control Panel Settings Webbing SettingsCleaning the Laminator Cleaning the RollersGreasing the Bearings E a N I N G / M a I N TA I N I N G Y O U R L a M I N AT O RR I O D I C M a I N T E N a N C E S H E E T Chain Tension Drain Water Adjustment/Oil Chain Air FilterGrease Bearings Problem Solution Technical ServiceLED PA R E PA R T S L I S T Mechanical ProcessElectrical Order CodesM I T E D W a R R a N T Y