SEAL 6500 Check the Main Power, Check the Emergency Stop Buttons, Check the Heater Controls

Page 16

C H E C K I N G O P E R AT I O N

After you are familiar with the control panels and their functions, check all operations.

Check the Main Power

•Press the Stand-By switch up and the front and back displays on the control panels should be lit.

•The center red switch on both top cabinet control panels should be illuminated.

Check the Emergency Stop Buttons

•Press one of the Emergency Stop buttons and the laminator will shut down.

•Rotate the Emergency Stop button clockwise to reset.

•Repeat this procedure with all four Emergency Stop buttons.

Check the Heater Controls

•Press the top heater On/Off button once; the corre- sponding LED should be lit.

•The readout will display the ambient temperature.

•Press and hold the top heater Up arrow to increase the temperature set point. Watch the readout for 5 minutes to verify that the temperature increases.

•Press and hold the Down arrow to decrease the tempera- ture set point.

•Press the top heater On/Off button again once; the corresponding LED should not be lit.

•Repeat this procedure for the bottom heater.

Check the Motor and Foot Switches

Check both motor control panels as follows:

•Push the green Motor Forward switch and the rollers should rotate in the forward direction.

•Press the green Motor Reverse switch and the rollers should rotate in the reverse direction.

•As you turn the Speed Control knob clockwise the speed of the rollers should increase and the speed readout (top display on front and rear control panels) should increase in number.

•Turning the Speed Control knob counter-clockwise should decrease the speed of the rollers and the speed readouts should decrease in number.

•Press the center red Motor Stop switch and the rollers should stop rotating.

•Press the foot switch and the rollers should rotate in whichever roller direction that was last pressed. Check both foot switches for operation.

CHECKING THE ROLLERS

Your laminator has a pneumatic pressure adjustment with fine-tune control for a smooth, flat finish. Correct adjust- ment of the pressure rollers’ height is essential for safe and proper operation. Check this prior to every use.

Check the vertical movement of the top rollers as follows:

•Press the roller switch UP. The top roller should rise smoothly and evenly on both ends.

•Press the roller switch DOWN. The top roller should lower smoothly and evenly on both ends.

•Repeat this procedure for both front and back top rollers.

IMPORTANT! The silicone covering of the rollers is soft. Do not scratch the surface with a sharp object or fingernail.

WARNING! If your laminator does not operate cor- rectly, contact Technical Service immediately.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Image 6500 Laminator Page Statement of Intended USE T R O D U C T I O NConnecting Your Laminator E C T R I C a L S P E C I F I C AT I O N SMedia R K S PA C E R E Q U I R E M E N T SAmbient Temperature Power SupplyRelative Humidity Water and MoistureAccessories Included PA C K I N G , S E T- U P a N D I N S TA L L AT I O NUnpacking Your Laminator Leveling Your LaminatorServicing and Replacement Parts Rotating Parts Risk of InjuryHot Surface Risk of Injury on Contact Electrical Parts Danger of being injured by electricityF E T Y F E AT U R E S Door InterlockFeatures M I N AT O R F E AT U R E SO N T C O N T R O L PA N E L Front Control PanelC K C O N T R O L PA N E L Back Control PanelAIR Regulator Knob AIR Pressure GaugeU T C H C O N T R O L PA N E L Speed Adjustment Knob Reverse Roller Direction SwitchMotor Stop Switch Forward Roller Direction SwitchCheck the Main Power Check the Motor and Foot SwitchesCheck the Emergency Stop Buttons Check the Heater ControlsTemperature Settings HOW to SET the Shim WheelsShim Wheel Settings T- U P a N D O P E R AT I O NUnwind shaft cord adjustment Loading a Roll of MaterialPivoting Table USE for Webbing Pivoting Roll Easel Bracket DownSetting the Unwind Brake Tension Cooling SystemTo remove the cooling tube from the bottom location To insert the cooling tube in the top locationAUTO-RUN Operation Foot Switch OperationRotation of the Rollers will Stop When Using the Print Guide Table Using the Roll Easel AttachmentBasic Steps to Feeding Images E D I N G I M a G E SYou are now ready to feed images B B I N G F I L M S W I T H O U T a R E L E a S E L I N E RYOU are NOW Ready to Feed Images B B I N G F I L M S W I T H a R E L E a S E L I N E RWebbing Settings FilmsMedia Ink Jet, Electrostatic, and Photographic Webbing for Decaling Pressure-sensitive filmsTo Mount Decals Onto a Substrate U N T I N GC a P S U L AT I N G FrontPreparation E C O AT I N G B O a R D SMedia Electrostatic Webbing for Vinyl TransferFront Control Panel Settings Back Control Panel SettingsMotor Control Panel Settings Webbing SettingsCleaning the Laminator Cleaning the RollersGreasing the Bearings E a N I N G / M a I N TA I N I N G Y O U R L a M I N AT O RGrease Bearings Chain Tension Drain Water Adjustment/Oil Chain Air FilterR I O D I C M a I N T E N a N C E S H E E T Problem Solution Technical ServiceLED PA R E PA R T S L I S T Mechanical ProcessElectrical Order CodesM I T E D W a R R a N T Y
Top Page Image Contents