SEAL 6500 owner manual Grease Bearings, Chain Tension Drain Water Adjustment/Oil Chain Air Filter

Page 33

Grease Bearings

P E R I O D I C M A I N T E N A N C E S H E E T

Chain Tension

Drain Water

Adjustment/Oil Chain**

(Air Filter)***

 

 

Safety Check After Servicing

NOTE: Enter dates of service and initials of service personnel.

We recommend that you make a photocopy of this page, tape it to the inside of the cabinet door and use this to record dates that authorized safety or maintenance personnel perform these laminator maintenance procedures.

Proper maintenance of your laminator ensures receiving many years of profit from your investment.

Use only replacement parts specified by SEAL Graphics.

**Use lightweight household oil to oil the chain approximately every three months.

***Drain the air filter approximately every six months to prevent moisture damage to the air cylinders.

Call SEAL Graphics Technical Service for assistance (see the rear cover).

33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Image 6500 Laminator Page T R O D U C T I O N Statement of Intended USEE C T R I C a L S P E C I F I C AT I O N S Connecting Your LaminatorR K S PA C E R E Q U I R E M E N T S MediaPower Supply Ambient TemperatureRelative Humidity Water and MoisturePA C K I N G , S E T- U P a N D I N S TA L L AT I O N Accessories IncludedLeveling Your Laminator Unpacking Your LaminatorRotating Parts Risk of Injury Servicing and Replacement PartsHot Surface Risk of Injury on Contact Electrical Parts Danger of being injured by electricityDoor Interlock F E T Y F E AT U R E SM I N AT O R F E AT U R E S FeaturesFront Control Panel O N T C O N T R O L PA N E LBack Control Panel C K C O N T R O L PA N E LAIR Pressure Gauge AIR Regulator KnobU T C H C O N T R O L PA N E L Reverse Roller Direction Switch Speed Adjustment KnobMotor Stop Switch Forward Roller Direction SwitchCheck the Motor and Foot Switches Check the Main PowerCheck the Emergency Stop Buttons Check the Heater ControlsHOW to SET the Shim Wheels Temperature SettingsShim Wheel Settings T- U P a N D O P E R AT I O NLoading a Roll of Material Unwind shaft cord adjustmentPivoting Roll Easel Bracket Down Pivoting Table USE for WebbingCooling System Setting the Unwind Brake TensionTo remove the cooling tube from the bottom location To insert the cooling tube in the top locationFoot Switch Operation AUTO-RUN OperationRotation of the Rollers will Stop When Using the Roll Easel Attachment Using the Print Guide TableBasic Steps to Feeding Images E D I N G I M a G E SB B I N G F I L M S W I T H O U T a R E L E a S E L I N E R You are now ready to feed imagesB B I N G F I L M S W I T H a R E L E a S E L I N E R YOU are NOW Ready to Feed ImagesFilms Webbing SettingsWebbing for Decaling Pressure-sensitive films Media Ink Jet, Electrostatic, and PhotographicU N T I N G To Mount Decals Onto a SubstrateFront C a P S U L AT I N GE C O AT I N G B O a R D S PreparationWebbing for Vinyl Transfer Media ElectrostaticBack Control Panel Settings Front Control Panel SettingsMotor Control Panel Settings Webbing SettingsCleaning the Rollers Cleaning the LaminatorGreasing the Bearings E a N I N G / M a I N TA I N I N G Y O U R L a M I N AT O RChain Tension Drain Water Adjustment/Oil Chain Air Filter Grease BearingsR I O D I C M a I N T E N a N C E S H E E T Technical Service Problem SolutionLED PA R E PA R T S L I S T Process MechanicalElectrical Order CodesM I T E D W a R R a N T Y
Top Page Image Contents