SEAL 6500 Ambient Temperature, Relative Humidity, Water and Moisture, Surroundings, Power Supply

Page 6

E N V I R O N M E N T C O N D I T I O N S

The following environmental conditions are ideal for the best operation of the laminator.

AMBIENT TEMPERATURE

The best temperature for the SEAL Image 6500 is between 50°F and 86°F (10°C and 30°C).

Do not expose the laminator to direct sunlight as output quality may be affected.

RELATIVE HUMIDITY

For best results, the ambient relative humidity for the SEAL Image 6500 should be between 70-90% non-con- densing. Too much humidity will affect the prints being laminated causing problems with film adhesion.

WATER AND MOISTURE

If the laminator is installed in a damp room or near water, the electrical power supply must be in accordance with the standards prevailing in the country concerned.

SURROUNDINGS

Install the laminator in surroundings that are as clean and dust-free as possible in order to obtain the highest quality output.

The background dust level must not exceed that found in a typical office/computer room environment.

The materials that are used on this laminator can have an electrostatic charge and will attract dust, adversely affect- ing the output.

POWER SUPPLY

Connect the laminator in accordance with the details given on the identification plate attached to the rear of the laminator. Refer also to the Technical Specifications page for more information.

6

Image 6

Contents Image 6500 Laminator Page Statement of Intended USE T R O D U C T I O NConnecting Your Laminator E C T R I C a L S P E C I F I C AT I O N SMedia R K S PA C E R E Q U I R E M E N T SRelative Humidity Ambient TemperaturePower Supply Water and MoistureAccessories Included PA C K I N G , S E T- U P a N D I N S TA L L AT I O NUnpacking Your Laminator Leveling Your LaminatorHot Surface Risk of Injury on Contact Servicing and Replacement PartsRotating Parts Risk of Injury Electrical Parts Danger of being injured by electricityF E T Y F E AT U R E S Door InterlockFeatures M I N AT O R F E AT U R E SO N T C O N T R O L PA N E L Front Control PanelC K C O N T R O L PA N E L Back Control PanelAIR Pressure Gauge AIR Regulator KnobU T C H C O N T R O L PA N E L Motor Stop Switch Speed Adjustment KnobReverse Roller Direction Switch Forward Roller Direction SwitchCheck the Emergency Stop Buttons Check the Main PowerCheck the Motor and Foot Switches Check the Heater ControlsShim Wheel Settings Temperature SettingsHOW to SET the Shim Wheels T- U P a N D O P E R AT I O NUnwind shaft cord adjustment Loading a Roll of MaterialPivoting Table USE for Webbing Pivoting Roll Easel Bracket DownTo remove the cooling tube from the bottom location Setting the Unwind Brake TensionCooling System To insert the cooling tube in the top locationFoot Switch Operation AUTO-RUN OperationRotation of the Rollers will Stop When Basic Steps to Feeding Images Using the Print Guide TableUsing the Roll Easel Attachment E D I N G I M a G E SYou are now ready to feed images B B I N G F I L M S W I T H O U T a R E L E a S E L I N E RYOU are NOW Ready to Feed Images B B I N G F I L M S W I T H a R E L E a S E L I N E RWebbing Settings FilmsMedia Ink Jet, Electrostatic, and Photographic Webbing for Decaling Pressure-sensitive filmsTo Mount Decals Onto a Substrate U N T I N GC a P S U L AT I N G FrontPreparation E C O AT I N G B O a R D SMedia Electrostatic Webbing for Vinyl TransferMotor Control Panel Settings Front Control Panel SettingsBack Control Panel Settings Webbing SettingsGreasing the Bearings Cleaning the LaminatorCleaning the Rollers E a N I N G / M a I N TA I N I N G Y O U R L a M I N AT O RChain Tension Drain Water Adjustment/Oil Chain Air Filter Grease BearingsR I O D I C M a I N T E N a N C E S H E E T Problem Solution Technical ServiceLED PA R E PA R T S L I S T Electrical MechanicalProcess Order CodesM I T E D W a R R a N T Y