SEAL 6500 owner manual C a P S U L AT I N G, Front

Page 28

E N C A P S U L AT I N G

This process involves completely sealing an image between two films. Follow the webbing instructions for films specific for your location.

MEDIA: Ink Jet, Electrostatic, and Photographic

FILMS:

---- -- Top Unwind Shaft: Heat-Activated Laminate 3–5 Mil (75-125 microns)

____ Bottom Unwind Shaft: Heat-Activated Laminate

3–5 Mil (75-125 microns)

LAMINATOR SETTINGS:
Front Control Panel
Top Roller Temp.:	205-215°F (96-102°C)
Bottom Roller Temp.:	205-215°F (96-102°C)
Main Roller Pressure:	35-40 PSI
Cooling Fan:	OFF
Back Control Panels
Pull Rollers:	Down
Pull Roller Pressure:	35-40 PSI
Pull Clutch Tension:	40-60 PSI
Motor Control Panel
Motor Direction:	Forward
Motor Speed Setting:	3-5 FPM (1-1.5 MPM)
WEBBING SETTINGS
Web Tension Top:	Medium
Web Tension Bottom:	Medium
Chill Idlers:	Over 1st/Under 2nd
Shim Wheel Settings:	-1/16" (-2mm)

28

	Rear	Shim Wheel			Shim Wheel	Front
	Rear					Front
						Front Top
			Rear Top	Front Top		Wind-up
		Rear Top	Supply Shaft	Supply Shaft
		Wind-up
			Top
			Idler
Rear		Top			Top	Front
Rear		Pull Roller			Main Roller	Front
Roll		Pull Roller			Main Roller	Roll
Easel	Rear Table		Chill			Easel
	Rear Table		Idler			Print Guide
			Idler			Print Guide
		Bottom		Chill	Bottom	Front Table
		Pull Roller		Idler	Main Roller
			Fan
			Tube
	Rear		Bott		Bott	Front
	Bottom		Bott		Bott	Front
	Wind-up		Idler		Idler	Bottom
	Wind-up		Idler		Idler	Wind-up
						Wind-up
	Rear					Front
	Bottom					Bottom
	Supply					Supply
Covered	Shaft					Shaft
Covered						Covered
Foot						Foot
Switch						Switch

Figure 24. Webbing for Encapsulating

Image 28

Contents Image 6500 Laminator Page Statement of Intended USE T R O D U C T I O NConnecting Your Laminator E C T R I C a L S P E C I F I C AT I O N SMedia R K S PA C E R E Q U I R E M E N T SAmbient Temperature Power SupplyRelative Humidity Water and MoistureAccessories Included PA C K I N G , S E T- U P a N D I N S TA L L AT I O NUnpacking Your Laminator Leveling Your LaminatorServicing and Replacement Parts Rotating Parts Risk of InjuryHot Surface Risk of Injury on Contact Electrical Parts Danger of being injured by electricityF E T Y F E AT U R E S Door InterlockFeatures M I N AT O R F E AT U R E SO N T C O N T R O L PA N E L Front Control PanelC K C O N T R O L PA N E L Back Control PanelAIR Regulator Knob AIR Pressure GaugeU T C H C O N T R O L PA N E L Speed Adjustment Knob Reverse Roller Direction SwitchMotor Stop Switch Forward Roller Direction SwitchCheck the Main Power Check the Motor and Foot SwitchesCheck the Emergency Stop Buttons Check the Heater ControlsTemperature Settings HOW to SET the Shim WheelsShim Wheel Settings T- U P a N D O P E R AT I O NUnwind shaft cord adjustment Loading a Roll of MaterialPivoting Table USE for Webbing Pivoting Roll Easel Bracket DownSetting the Unwind Brake Tension Cooling SystemTo remove the cooling tube from the bottom location To insert the cooling tube in the top locationAUTO-RUN Operation Foot Switch OperationRotation of the Rollers will Stop When Using the Print Guide Table Using the Roll Easel AttachmentBasic Steps to Feeding Images E D I N G I M a G E SYou are now ready to feed images B B I N G F I L M S W I T H O U T a R E L E a S E L I N E RYOU are NOW Ready to Feed Images B B I N G F I L M S W I T H a R E L E a S E L I N E R Webbing Settings FilmsMedia Ink Jet, Electrostatic, and Photographic Webbing for Decaling Pressure-sensitive filmsTo Mount Decals Onto a Substrate U N T I N GC a P S U L AT I N G FrontPreparation E C O AT I N G B O a R D SMedia Electrostatic Webbing for Vinyl TransferFront Control Panel Settings Back Control Panel SettingsMotor Control Panel Settings Webbing SettingsCleaning the Laminator Cleaning the RollersGreasing the Bearings E a N I N G / M a I N TA I N I N G Y O U R L a M I N AT O RGrease Bearings Chain Tension Drain Water Adjustment/Oil Chain Air FilterR I O D I C M a I N T E N a N C E S H E E T Problem Solution Technical ServiceLED PA R E PA R T S L I S T Mechanical ProcessElectrical Order CodesM I T E D W a R R a N T Y