SEAL 6500 AUTO-RUN Operation, Foot Switch Operation, Rotation of the Rollers will Stop When

Page 21

S E T- U P A N D O P E R AT I O N

AUTO-RUN OPERATION

The continuous-run operation allows the user to set the direction of the roller rotation and adjust the roller speed by turning either of the Speed Control knobs on the tops of the cabinets.

This feature is useful for long runs that don’t require much user control and, when used in combination with the roll easel shaft and wind-up shafts, can be efficient in an auto-run mode.

Press the motor direction switch for the processing direc- tion desired.

Turn the Speed Control knob on either of the Motor Control Panels to adjust the speed of the rollers (refer to the Top Motor Control Panel page).

IMPORTANT! If the photoelectric eyes become blocked during continuos-run operation, the roller rotation will stop immediately.

IMPORTANT! Take care not to stop the motor or block the photoelectric eyes while an image is being laminated as this can cause marks in the output.

FOOT SWITCH OPERATION

The function of the foot switch is to permit the rotation of the rollers to be controlled in a hands-free manner.

This feature can be used when webbing materials onto the laminator or feeding delicate images and overrides the photoelectric safety eyes.

Pressing the foot switch runs the laminator in the direc- tion that was pressed last (the Active Directional Switch will be illuminated).

The rollers will run at the speed last set which is indicat- ed in the top display on either front or back control panels.

The speed can be adjusted when using the foot switch by turning either Speed Control knob on the top of the cabinets.

WARNING! While using the foot switch, interrupting the photoelectric safety eyes does NOT stop the lamina- tor. An audible beep will be heard, the Motor Directional Switch will be blinking and the roller speed will run in ‘slow mode’ at a speed of 2ft./min. (0.6 m/min.). Releasing the foot switch will stop the laminator.

After clearing the photoelectric eye blockage the buzzer will stop.

To resume the pre-set speed, press the blinking direction- al switch.

CHANGING FROM FOOT SWITCH OPERATION TO AUTO-RUN MODE WITHOUT STOPPING (to prevent stop marks on the substrate):

During foot switch operation (keep the foot switch pressed), then press Motor Direction switch desired on either Motor Control panel. The laminator will run at the pre-set speed.

Next, release the foot switch.

IMPORTANT! Do not stop the motor or block the photoelectric eyes while an image is being laminated as this can cause marks in the output.

THE ROTATION OF THE ROLLERS WILL STOP WHEN:

The photoelectric eyes in the front or back of the rollers are interrupted.

NOTE: This does NOT happen when the foot switch is used.

An Emergency Stop button is pressed.

An emergency tap switch is pressed.

The Stop button on the motor control panel is pressed.

21

Image 21
Contents Image 6500 Laminator Page T R O D U C T I O N Statement of Intended USEE C T R I C a L S P E C I F I C AT I O N S Connecting Your LaminatorR K S PA C E R E Q U I R E M E N T S MediaPower Supply Ambient TemperatureRelative Humidity Water and MoisturePA C K I N G , S E T- U P a N D I N S TA L L AT I O N Accessories IncludedLeveling Your Laminator Unpacking Your LaminatorRotating Parts Risk of Injury Servicing and Replacement PartsHot Surface Risk of Injury on Contact Electrical Parts Danger of being injured by electricityDoor Interlock F E T Y F E AT U R E SM I N AT O R F E AT U R E S FeaturesFront Control Panel O N T C O N T R O L PA N E LBack Control Panel C K C O N T R O L PA N E LAIR Pressure Gauge AIR Regulator KnobU T C H C O N T R O L PA N E L Reverse Roller Direction Switch Speed Adjustment KnobMotor Stop Switch Forward Roller Direction SwitchCheck the Motor and Foot Switches Check the Main PowerCheck the Emergency Stop Buttons Check the Heater ControlsHOW to SET the Shim Wheels Temperature SettingsShim Wheel Settings T- U P a N D O P E R AT I O NLoading a Roll of Material Unwind shaft cord adjustmentPivoting Roll Easel Bracket Down Pivoting Table USE for WebbingCooling System Setting the Unwind Brake TensionTo remove the cooling tube from the bottom location To insert the cooling tube in the top locationFoot Switch Operation AUTO-RUN OperationRotation of the Rollers will Stop When Using the Roll Easel Attachment Using the Print Guide TableBasic Steps to Feeding Images E D I N G I M a G E SB B I N G F I L M S W I T H O U T a R E L E a S E L I N E R You are now ready to feed imagesB B I N G F I L M S W I T H a R E L E a S E L I N E R YOU are NOW Ready to Feed ImagesFilms Webbing SettingsWebbing for Decaling Pressure-sensitive films Media Ink Jet, Electrostatic, and PhotographicU N T I N G To Mount Decals Onto a SubstrateFront C a P S U L AT I N GE C O AT I N G B O a R D S PreparationWebbing for Vinyl Transfer Media ElectrostaticBack Control Panel Settings Front Control Panel SettingsMotor Control Panel Settings Webbing SettingsCleaning the Rollers Cleaning the LaminatorGreasing the Bearings E a N I N G / M a I N TA I N I N G Y O U R L a M I N AT O RChain Tension Drain Water Adjustment/Oil Chain Air Filter Grease BearingsR I O D I C M a I N T E N a N C E S H E E T Technical Service Problem SolutionLED PA R E PA R T S L I S T Process MechanicalElectrical Order CodesM I T E D W a R R a N T Y