SEAL 6500 owner manual Cleaning the Laminator, Greasing the Bearings, Cleaning the Rollers

Page 32

C L E A N I N G / M A I N TA I N I N G Y O U R L A M I N AT O R

WARNING! Turn the door interlock to the OFF position and then disconnect the laminator from the power supply before cleaning or greasing the bearings.

CLEANING THE LAMINATOR

•The laminator may be cleaned with a lint-free cloth, lightly dampened with a mild soap and water solution. Do not use spray-on cleaners. Do not immerse any part of the laminator in water or other liquids.

•Do not use an abrasive cleaner, which can damage the painted surfaces.

•Do not allow water or liquids to enter the electrical cir- cuits, which may cause personal injury and/or damage the equipment when power is applied.

GREASING THE BEARINGS

•You must grease the top and bottom roller bearings once each month or every 200 hours. Refer to the Grease Gun Kit included in your accessory kit for supplies and instructions.

WARNING! Failure to lube bearings will cause prema- ture wear, which may cause costly repairs and will void your warranty.

Call SEAL Graphics Technical Service for further assistance (see rear cover).

CLEANING THE ROLLERS

IMPORTANT! Clean the laminating rollers every day to prevent adhesive build-up and to ensure quality output. Adhesive build up may eventually damage the rollers.

•When laminating, a small amount of adhesive will squeeze out between the laminate films and onto the top and bottom rollers. This residue accumulates through normal use and can be easily cleaned off the rollers.

•Use the Image Roll Cleaner (included) to remove the excess adhesive from the rollers. This is best done with the rollers hot.

WARNING! Use only an Image Roll Cleaner or a cotton cloth and Isopropyl Alcohol (IPA) to clean the rollers. Do not use other solvents or cleaners. Use of other cleaners or solvents may cause roller damage and will void the warranty.

•When cleaning the upper roller, place a piece of scrap foam board under the roller to prevent the removed adhesive remnants from falling onto the lower roller.

•For adhesive that is difficult to remove, allow the rollers to cool and use isopropyl alcohol (IPA) and a clean, lint- free cloth. Never pour isopropyl alcohol (IPA) directly onto the unit.

CAUTION! Always use care when using Isopropyl Alcohol (IPA)! IPA is very flammable. The flash point of IPA is 51.8°F (11°C). The self-ignition temperature is 752°F (400°C). Wear rubber gloves and use in a well-ventilated area.

32

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Image 6500 Laminator Page Statement of Intended USE T R O D U C T I O NConnecting Your Laminator E C T R I C a L S P E C I F I C AT I O N SMedia R K S PA C E R E Q U I R E M E N T SAmbient Temperature Power SupplyRelative Humidity Water and MoistureAccessories Included PA C K I N G , S E T- U P a N D I N S TA L L AT I O NUnpacking Your Laminator Leveling Your LaminatorServicing and Replacement Parts Rotating Parts Risk of InjuryHot Surface Risk of Injury on Contact Electrical Parts Danger of being injured by electricityF E T Y F E AT U R E S Door InterlockFeatures M I N AT O R F E AT U R E SO N T C O N T R O L PA N E L Front Control PanelC K C O N T R O L PA N E L Back Control PanelU T C H C O N T R O L PA N E L AIR Pressure GaugeAIR Regulator Knob Speed Adjustment Knob Reverse Roller Direction SwitchMotor Stop Switch Forward Roller Direction SwitchCheck the Main Power Check the Motor and Foot SwitchesCheck the Emergency Stop Buttons Check the Heater ControlsTemperature Settings HOW to SET the Shim WheelsShim Wheel Settings T- U P a N D O P E R AT I O NUnwind shaft cord adjustment Loading a Roll of MaterialPivoting Table USE for Webbing Pivoting Roll Easel Bracket DownSetting the Unwind Brake Tension Cooling SystemTo remove the cooling tube from the bottom location To insert the cooling tube in the top locationRotation of the Rollers will Stop When Foot Switch OperationAUTO-RUN Operation Using the Print Guide Table Using the Roll Easel AttachmentBasic Steps to Feeding Images E D I N G I M a G E SYou are now ready to feed images B B I N G F I L M S W I T H O U T a R E L E a S E L I N E RYOU are NOW Ready to Feed Images B B I N G F I L M S W I T H a R E L E a S E L I N E RWebbing Settings FilmsMedia Ink Jet, Electrostatic, and Photographic Webbing for Decaling Pressure-sensitive filmsTo Mount Decals Onto a Substrate U N T I N GC a P S U L AT I N G FrontPreparation E C O AT I N G B O a R D SMedia Electrostatic Webbing for Vinyl TransferFront Control Panel Settings Back Control Panel SettingsMotor Control Panel Settings Webbing SettingsCleaning the Laminator Cleaning the RollersGreasing the Bearings E a N I N G / M a I N TA I N I N G Y O U R L a M I N AT O RR I O D I C M a I N T E N a N C E S H E E T Chain Tension Drain Water Adjustment/Oil Chain Air FilterGrease Bearings Problem Solution Technical ServiceLED PA R E PA R T S L I S T Mechanical ProcessElectrical Order CodesM I T E D W a R R a N T Y
Top Page Image Contents