SEAL 6500 owner manual Pivoting Table USE for Webbing, Pivoting Roll Easel Bracket Down

Page 19

S E T- U P A N D O P E R AT I O N

PIVOTING TABLE USE FOR WEBBING

First, remove the roll easel shaft from its brackets and set aside.

Pull out both retaining plungers of the roll easel brackets and pivot the brackets down and forward as shown in Figure 12.

Pull the film up and place it over the top roller.

Reposition the table by lifting the outer edge upwards and pivot in towards the roller (Figure 14).

With the table resting on the table bracket standoffs, lift the outer edge of the table and push the table in towards the roller (see Figure 15). The non-locking retaining plunger will catch automatically.

Moving to the right-hand side of the table release the locking retaining plunger so it locks in place.

The table operation is the same front and rear.

Figure 12. Pivoting Roll Easel Bracket Down

Remove the top and bottom wind-up idlers for easy webbing and set them aside.

On the right-hand side of the table, pull out the locking retaining plunger and turn sideways to lock with plunger recessed (see Figure 13).

Move to the left side and pull out the non-locking retaining plunger on the left-hand side of the table.

Allow the table brackets to slide outwards and down.

Grasp the front edge of the table and, lifting up, pivot the table towards you, away from the rollers (see Figure 13).

Reach through the opening between the table and rollers and pull the bottom film up and pass it behind the bot- tom idler.

Figure 13.

Figure 14

Releasing Retaining Plunger

Pivoting Table Up

Figure 15.

Pivoting Table Forwards

19

Image 19
Contents Image 6500 Laminator Page T R O D U C T I O N Statement of Intended USEE C T R I C a L S P E C I F I C AT I O N S Connecting Your LaminatorR K S PA C E R E Q U I R E M E N T S MediaWater and Moisture Ambient TemperaturePower Supply Relative HumidityPA C K I N G , S E T- U P a N D I N S TA L L AT I O N Accessories IncludedLeveling Your Laminator Unpacking Your LaminatorElectrical Parts Danger of being injured by electricity Servicing and Replacement PartsRotating Parts Risk of Injury Hot Surface Risk of Injury on ContactDoor Interlock F E T Y F E AT U R E SM I N AT O R F E AT U R E S FeaturesFront Control Panel O N T C O N T R O L PA N E LBack Control Panel C K C O N T R O L PA N E LAIR Regulator Knob AIR Pressure GaugeU T C H C O N T R O L PA N E L Forward Roller Direction Switch Speed Adjustment KnobReverse Roller Direction Switch Motor Stop SwitchCheck the Heater Controls Check the Main PowerCheck the Motor and Foot Switches Check the Emergency Stop ButtonsT- U P a N D O P E R AT I O N Temperature SettingsHOW to SET the Shim Wheels Shim Wheel SettingsLoading a Roll of Material Unwind shaft cord adjustmentPivoting Roll Easel Bracket Down Pivoting Table USE for WebbingTo insert the cooling tube in the top location Setting the Unwind Brake TensionCooling System To remove the cooling tube from the bottom locationAUTO-RUN Operation Foot Switch OperationRotation of the Rollers will Stop When E D I N G I M a G E S Using the Print Guide TableUsing the Roll Easel Attachment Basic Steps to Feeding ImagesB B I N G F I L M S W I T H O U T a R E L E a S E L I N E R You are now ready to feed imagesB B I N G F I L M S W I T H a R E L E a S E L I N E R YOU are NOW Ready to Feed ImagesFilms Webbing SettingsWebbing for Decaling Pressure-sensitive films Media Ink Jet, Electrostatic, and PhotographicU N T I N G To Mount Decals Onto a SubstrateFront C a P S U L AT I N GE C O AT I N G B O a R D S PreparationWebbing for Vinyl Transfer Media ElectrostaticWebbing Settings Front Control Panel SettingsBack Control Panel Settings Motor Control Panel SettingsE a N I N G / M a I N TA I N I N G Y O U R L a M I N AT O R Cleaning the LaminatorCleaning the Rollers Greasing the BearingsGrease Bearings Chain Tension Drain Water Adjustment/Oil Chain Air FilterR I O D I C M a I N T E N a N C E S H E E T Technical Service Problem SolutionLED PA R E PA R T S L I S T Order Codes MechanicalProcess ElectricalM I T E D W a R R a N T Y