AMT Datasouth 4500 Series manual Maintenance, Removing the Ribbon Take-up Roll

Page 57

Maintenance

Maintenance

The CodeWriter 4500 Series printers require very little operator maintenance. The routine tasks involve keeping the media paths clear of paper dust and debris.

NOTE: Turn off power while performing maintenance tasks.

Removing the Ribbon Take-up Roll

Use the following procedure to remove the ribbon take up roll:

1.Lift the Media Access Cover using the tab in the bottom center side of the cover. DO NOT lift from the front panel.

2.Find the “PRESS HERE” label affixed to the Printhead Bracket. Press down on the Printhead Bracket where indicated and rotate the Printhead Lock Lever back to unlock the bracket. Swing the Printhead Bracket up and back to expose the document path.

3.Remove any remaining ribbon trailer material from the supply core.

4.Grab the inside edge of the take-up roll with one hand and brace the printer with the other. Pull firmly to remove take-up roll.

5.If a take-up core is required for the next ribbon, move the supply core to the take- up shaft.

6.Continue with the following maintenance tasks.

47

Image 57

Contents CodeWriter 4500 Series Operator’s Manual Page Warnung Warnung Adventercia Hardware Warranty Extended MaintenanceDatasouth CodeWriter 4500 Disclaimer of Warranties SoftwareDatasouth Table of Contents Contents Table of Figures CodeWriter 4500 Series Models IntroductionCodeWriter 4505 Front/Side View External Media Feed Slot Operator Panel Document Exit Tear BarCodeWriter 4500 Series Features Media Compatibility FeaturesGuide to the Operator’s Manual This Page Intentionally Blank Unpacking and Power Up Equipment ChecklistQuick Start Guide Applying Power to the Printer Loading and Feeding Label Roll Media LoadingRibbon Take-Up Ribbon Supply Roll Ribbon Guide Bar Loading and Feeding the RibbonCodeWriter 4500 Series Operator Panel Operator Panel Media SettingsSet Label Parameters Without saving. Press the saving the changes Printer Model Print Speed 4505 100% 4505+ 4510 50% Set Print ParametersFeature/Settings Label Printing Test LabelsPrint Test Label Connecting the Printer Quick Start CDRunning the Quick Start CD Connecting the Cable Connecting to a Personal ComputerData Communications CableSettings Control Panel Configuring the Personal ComputerPort Settings Value Bits per second Mode COMx9600,n,8,1Mode COMx9600,n,8,1 where x = the COM port number Sending Data to the PrinterType File.pal COMx Cable Examples Serial Port SpecificationsSeries Printer DCE Modem DB25 Connector Hardware Flow Control Flow ControlDSR Xon/Xoff Flow ControlSetting the Baud Rate Operator Panel Settings for Data CommunicationsSetting the Flow Control Method Setting RTS PolaritySetting the Parity Setting the DTR PolaritySetting the Data Bits Setting the Stop BitsThis Page Intentionally Blank Media Settings Setting the Document DimensionsDie-Cut Labels Notch or Hole Label Black Bar LabelsEnter to save new defaults. Press Programming the Label DimensionsPressing the settings Programming the Print Method Setting the Printing MethodPrint Speed and Darkness Setting the Print ParametersSpeed Darkness Setting Print Speed and DarknessAdjusting Print Position Forward Distance Presentation DistanceBar Code Quality Bar Code OrientationPicket Fence Horizontal Bar Code Ladder Vertical Bar Code Bar Code Print Settings This Page Intentionally Blank Display and Panel Keys Operator Panel ReferenceOff-line Menu Reference Parameter Values Description Print Speed % Accessing this parameterPrinting Speed as a 80% 100% Percentage of the printer’sLabel Parameters Config System Params Settings LabelFirmware Part No Firmware part number Revision are displayedConfiguration Default Parameter ValuesPrint Parameters System ParametersOff-Line Menu Map Removing the Ribbon Take-up Roll MaintenancePrinthead Cleaning Paper Path CleaningHeater Line Location Response to Display Messages Troubleshooting GuideRemove Ribbon Print or CANCEL? Media Feed Fault Print or CANCEL? Halt First Part of Label Content is Missing Print Quality IssuesSides or Top of Label Content is Missing Ribbon Wrinkling Causing Poor PrintMissing Dots in Label Data Communications Issues PC Reports Write Fault Error Writing to Device COMxHost System Does Not Report Errors, But Nothing Prints Controlling Hex Dump Mode Hex Dump ModeAdjusting the Gap Sensor Sensitivity Adjusting Sensor SensitivityPrinter is Displaying Media Feed Fault Message Adjusting the Black Bar Sensor Sensitivity Press the Pause key. This takes you to the off-line menu Adjusting the Ribbon Sensor Sensitivity Printer Displays Ribbon Out Message in Thermal Transfer Mode Verifying the Sensor Operation Key until the Enter to Select Diagnostics is displayedThis Page Intentionally Blank Applications Overview Printer Application Language PALLabel Genesis Fonts PAL Fonts and Bar CodesBar Codes Bar CodeEAN-13 EAN13 Codabar Postnet Maxicode MSI Plessy Establishing the Development Environment PAL Quick StartPAL will display the line as it Function Keystroke Hex ValueHas been typed so far Undo Ctrl/ULabel Tutorial Hello World Label OutputPAL Command SequencePAL Coordinate System Printing a Line Applications Overview Label Output World!Hello Hello World PAL Command SequencePrinting a Bar Code Label Output WorldApplications Guide Power Input and Output SpecificationsEnvironmental PhysicalSerial Communications MediaPrinting ProcessingHigh Speed Firmware Update Download Mode Advanced FeaturesAuto-Baud Firmware Update Download Mode Flash Memory ManagementRelease Identification Message Pause PAL Application Bootstrap BypassKey until Enter to Select Expert Settings is displayed Setting Contrast and PreheatEnter to save new defaults . Press Print Darkness ControlAdvanced Features