AMT Datasouth 7200 manual Temperature and Humidity, Power Connection, Power Line Conditions

Page 68

7200 APPENDIX

A.1.3 General Specifications and Power requirements

Dimensions and Weight

8.3 inches (210mm) W x 21.6 inches (550mm) D x 15.0 inches (380mm) H

Less than 35.3 lb. (16 kg )

Temperature and Humidity

Make sure that the following temperature and humidity conditions are met :

Ambient temperature: 41 to 104 degrees F (5 to 40 degrees C)

Ambient humidity: 20% to 90% RH (relative humidity) — no condensation.

Notes on the Operating Environment

When installing the product where the ambient humidity is 30% or less, it is recommended that you use a humidifier to raise the humidity to higher levels. Use an antistatic mat as necessary.

Power Connection

Power Line Conditions

Ensure that the power supply satisfies the following requirements:

Voltage: 85 to 132 or 170 to 265 VAC (automatic voltage switching)

Frequency: 47 to 63 Hz

Power consumption: 250 VAC (Printing) or 80 VAC (Stand by)

If the power line is unstable, use a voltage regulator or similar device.

Connecting to Power

To connect the ATB printer to the power line, follow the instructions below:

Plug the power cable of the printer in a dedicated wall receptacle. Do not plug any other electric products into the same receptacle. If the printer shares a receptacle with an air conditioner, copy machine, or shredder, faulty operation may result due to electric noise. If a dedicated wall receptacle cannot be used, use a commercially-available noise filter or transformer.

Route the power cable such that people do not step on it. Do not place anything on the power cable.

Important Note on the Side Cover

As a measure of safety, this ATB printer cannot be operated while the side cover is open.

Close the side cover and lock the cover with the key to print coupons.

Operation Manual

APPENDIX-3

Image 68
Contents 7200 Contents Is intentionally blank Introduction FCC Warning Product Safety Safety Considerations Operating Environment LocationSpace Required Power Line Conditions Connecting to PowerAvailable Types Type Printing Method Number of BinsViii Before Using the ATB Printer Checking the Package Names and Functions Names of PartsFunctions Names FunctionsOperator Panel LED FunctionsLCD Panel Functions Operator Panel LayoutKey Functions OnlineTest 7200 Operation Connecting the ATB Printer Connecting to a Wall ReceptacleConnecting the Terminal Turning the Power On and Off CHECK-IN TicketingKey cannot be removed in the Open position Loading the DocumentsLoading Documents into BINs 1 Document Orientation Visual 7200 Do not remove the documents from the box Setting Documents in BINKeep space for the documents Key cannot be removed Open position Close the side cover top right 7200 Loading Documents into the Inserter Installing the Transfer Ribbon TT Type D Only Pivots Lock Operation Following operation is only for thermal transfer Changing Transfer Ribbons TT Type D OnlyLCD Panel Display Treat used transfer ribbons as plastic waste 7200 Daily Maintenance Cleaning the ATB Printer Cleaning the Printer SurfaceCleaning the Magnetic Head Cleaning card is optional sold separatelyRepeat the cleaning procedure several times as necessary Cleaning the Thermal Head Cleaning a Platen Roller Cleaning a Carrier Roller Inserter and Magnetic BlocksTo Clean BIN Bin and Cutter BlocksRemoving Paper Dust 7200 Troubleshooting Jam Locations and Corresponding Messages Paper JamPart Names Removing the jammed coupon Jam Position Removing ProceduresUnlock the cover before starting any procedure For a jam in BIN For a jam in BIN 3 Option After the jammed coupon has been cut If the jammed coupon has not been cut Side pressure roller Method varies depending on the location of the jammed coupon To remove the jammed coupon, go to step E Rear end of the jammed ticket is on the blade Troubleshooting Error Messages Error Message Error State Recovery ProcedureTroubleshooting L O G I C a L Error M e s s a g e Error State Recovery Procedure 7200 Document Carrier Structure Appendix 1 SpecificationsDocument Carrier Structure Covers Side Covers Open/ClosedTemperature and Humidity Power ConnectionPower Line Conditions Connecting to PowerPrinting Encoding SpecificationsBins and Feeder Transfer Ribbon Printing Type D printers only InserterOutput Stacker Printer Accessories Appendix 2 ConsumablesThermal Transfer Ribbon StoringTransfer RibbonsAMT Datasouth Corp