Siemens 2614 manual LED Status Indicators

Page 10

If Internet services are provided through an xDSL or cable modem, use unshielded or shielded twisted- pair Ethernet cable with RJ-45 plugs to connect the broadband modem directly to the WAN port on the SpeedStream 2614. Use either straight-through or crossover cable depending on the port type provided by the modem (see Appendix B, “Cables”). For ISDN or PSTN service, attach the access device to the RS232 serial port on the SpeedStream 2614

4.Connect a printer. By connecting a printer to the SpeedStream 2614, all computers connected to your LAN can access print services. Connect a standard parallel printer cable to the printer port on the SpeedStream 2614 and configure printer services as instructed in Chapter 5, “Configuring Printer Services.”

5.Connect the power adapter and power up the router, modem and network computers. Plug the power adapter into the power socket on the SpeedStream 2614, and plug the other end into a power outlet. Check the Power indicator on the front panel to be sure it is on. If the Power indicator does not light up, refer to Appendix A, “Troubleshooting.”

6.Verify the port status. Confirm that all connections are successful by checking the power and port status indicators as shown in the following table.

LED

Ports

Color

Condition

Status

Power

n/a

Green

On

SpeedStream 2614 is receiving power.

 

 

 

 

 

 

WAN

n/a

Green

On

The WAN port has established a valid network connection.

 

 

 

Flashing

The WAN port is transmitting or receiving traffic.

 

 

 

 

 

 

LAN

 

 

 

 

 

- Link/Act

1-4

Green

On

The indicated LAN port has established a valid network

 

 

 

 

 

connection.

 

 

 

 

 

 

 

 

 

Flashing

The indicated LAN port is transmitting or receiving traffic.

- 10/100

1-4

Amber

On

The indicated LAN port is operating at 100 Mbps.

 

 

 

Flashing

 

The indicated LAN port is operating at 10 Mbps.

 

 

 

 

 

 

Table 2-2. LED Status Indicators

2-5

Image 10
Contents 2614 Table of Contents Appendixes Introduction Features and BenefitsAbout the SpeedStream Applications Package Contents Installing the SpeedstreamDescription of Hardware SpeedStream System Requirements Hardware InstallationInstallation Procedure Before StartingConnecting the SpeedStream LED Status Indicators Page Web Browser Management Interface Configuring the SpeedstreamNavigating the Management Interface Menu Selections Menu Item DescriptionOn the Tools menu, click Internet Options Configuration ChangesView Network and Device Status General box, select Temporary Internet FilesOn the Simple Setup menu, click Change Password Simple Setup ProceduresSet or Change a Password Set the Time ZoneConfigure the WAN Connection On the Simple Setup menu, click Set Time ZoneStatic IP Address Fixed IP Fill in the relevant fields under Secondary Dial-up Advanced Setup Procedures Configure LAN Gateway and Dhcp SettingsEnable Firewall Protection Enable Virtual ServerConfigure Special Applications Network Address Translation NATConfigure Miscellaneous Features Configure Client FilteringOn the Tools menu, click Change Password System ToolsUpdate Firmware Reset RouterRestore Factory Defaults Backup SettingsInstall the TCP/IP Protocol Installing and Configuring TCP/IPClick Start/Settings then click Control Panel Configure TCP/IP for the SpeedStream Dynamic IP Allocation via a Dhcp ServerManual IP Configuration TCP/IP VerificationIs TCP/IP properly configured on your computer? Configuring Printer Services Install the Print Server ProgramSpecified location Select Port Name Configure the Printer Port Windows 95/98/NT/MEWindows Select Printer PortSelect Local printer then click Next Unix Systems 11. Select Printer PortTroubleshooting Appendix aTechnical Support Cables Cable Types and SpecificationsAppendix B Ethernet CableSerial Port Pin Assignments RJ-45 Pin AssignmentsRJ-45 Pin Numbering Serial Port to 9-Pin COM Port on Computer DB-9 Port Pin AssignmentsSerial Port to 25-Pin DCE Port on Modem Printer Port Pin Assignments Serial Port to 25-Pin DTE Port on ComputerPin Signal Name Direction DB-25 Printer Port Pin AssignmentsSpecifications Temperature