Toshiba TDP-S8 Projector placement angle adjustments, Adjusting the screen size and focus

Page 26

5Projector placement angle adjustments

The placement angle and the height of the projected image can be adjusted by the foot adjuster.

Lift up the front of the projector to

1

the desired angle, then press the

 

foot adjuster release button.

 

The foot adjuster extends. Release the but-

 

ton to lock the position.

 

To adjust the horizontal angle, use

 

the tilt adjuster.

2

To stow the foot adjuster, hold up the projector

 

while pressing the foot adjuster release button,

 

then slowly lower the projector.

 

6Adjusting the screen size and focus

Use the zooming lever to adjust the screen size. 2 Use the focusing ring to adjust the focus.

Notes

1

2

•Note that a lamp characteristics may rarely cause the brightness to fluctuate slightly.

•A lamp is consumable item. If used for extended periods, images will appear dark, and the lamp could burn out. This is characteristic of a lamp, and is not malfunction. (The lifetime of the lamp depends on conditions of use.)

•The DMDTM is made using extremely advanced technology, but there may be black spots (pixels that do not light) or bright spots (pixels that are constantly lit) on the panel. Please note that these are not malfunctions.

•Although this projector supports a wide range of RGB signals p.42 , any resolutions not supported by this projector (SVGA) will be expanded or shrunk, which will affect image quality slightly. To view high-quality images, it is recommended that the computer’s external output should be set to SVGA resolution.

•With some models of computer having LCD displays or the like, displaying images simultaneously on the projector and the monitor’s display may prevent the images from displaying properly. If this happens, turn off the computer’s LCD display. For information on how to turn off the LCD display, see the owner’s manual of your computer.

•If no signal is being input from the connected equipment or signal input is stopped while projecting, the “No signal” will appear.

•If a signal not supported by the projector is input, the “Unsupport signal” will appear.

•If an unavailable operation button is pressed, the icon will appear.

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Data Projector TDP-S8 Safety Precautions USA onlyBefore Using Source of Light Important Safety InstructionsPower Sources Ventilation Heat Power-Cord ProtectionCleaning Water and MoistureObject and Liquid Entry Lightning stormsDo not place the product vertically Stack InhibitedServicing AccessoriesDamage Requiring Service Safety Check Important Safety InstructionsReplacement Parts Do not use the product in a closed installation statePlace and Manner of Installation Power Supply Cord SelectionImportant Precautions Save Original Packing MaterialsAvoid Volatile Liquid Important PrecautionsExemption Clauses Disposal Other Cautions and InformationsCopyrights TrademarksRemote Control Batteries Contents Page Checking the package contents Names of each part on the main unit Names of each part on the control panel and remote control Parts on the rear panel Operating the remote control Preparing and using the remote controlLoading dry-cell batteries Into the remote control Floor-mounted front projection PlacementPlacement Styles As seen from the side Projection Distance and SizeConnection Before connectionTurning the power on and off Turning the power on Press the ON/STANDBY buttonTurning the power off Press the ON/STANDBY button Press the ON/STANDBY button againBasic operations Turn on the powerSelect the language When using the first time Activate the connected device To adjust the horizontal angle, use Tilt adjuster Projector placement angle adjustmentsAdjusting the screen size and focus To stow the foot adjuster, hold up the projectorPress the remote control’s Auto SET button Using handy featuresUsing auto setting Only for analog input from computer Correcting the keystone distortionFreezing the image Freeze Password functionCutting off the picture and sound temporarily Mute Key LockRe-enter the same password for confirmation Using handy featuresIf you forgot the password, please inquire your dealer Using the menus How to use the menusImage adjustment menu Background Display setting menuDetailed description Screen size Detailed description Fan mode Using the menusDefault setting menu Lamp powerDisplaying Information Status display B/P RAbout lamp Lamp replacementWhen the lamp is broken Lamp replacement Reset the lamp timer Used LampsMain unit cleaning Lens and main unit cleaningLens cleaning Trouble indications No powerPower went out during use Lamp went out during use, or won’t come onBefore calling service personnel Separately sold product SpecificationsList of general specifications SpecificationList of supported signals RGB signals SpecificationsPin assignment of Computer in & Monitor terminals List of supported signals Y/PB/PR signalsList of supported signals Video, S-Video signals Control terminal Pin assignment
Top Page Image Contents