Toshiba TDP-T9 Projector placement angle adjustments, Adjusting the screen size and focus

Page 28

5Projector placement angle adjustments

The placement angle and the height of the projected image can be adjusted by the foot adjuster.

Lift up the front of the projector to

1

the desired angle, then press the

 

foot adjuster release button.

 

The foot adjuster extends. Release the but-

 

ton to lock the position.

 

To adjust the horizontal angle, use

 

the tilt adjuster.

2

To stow the foot adjuster, hold up the projector

 

while pressing the foot adjuster release button,

 

then slowly lower the projector.

 

6Adjusting the screen size and focus

Use the zooming lever to adjust the screen size. Use the focusing ring to adjust the focus.

Notes

1

2

•Note that a lamp characteristics may rarely cause the brightness to fluctuate slightly.

•A lamp is consumable item. If used for extended periods, images will appear dark, and the lamp could burn out. This is characteristic of a lamp, and is not malfunction. (The lifetime of the lamp depends on conditions of use.)

•The DMDTM is made using extremely advanced technology, but there may be black spots (pixels that do not light) or bright spots (pixels that are constantly lit) on the panel. Please note that these are not malfunctions.

•Although this projector supports a wide range of RGB signals p.44 , any resolutions not supported by this projector (XGA) will be expanded or shrunk, which will affect image quality slightly. To view high-quality images, it is recommended that the computer’s external output should be set to XGA resolution.

•With some models of computer having LCD displays or the like, displaying images simultaneously on the projector and the monitor’s display may prevent the images from displaying properly. If this happens, turn off the computer’s LCD display. For information on how to turn off the LCD display, see the owner’s manual of your computer.

•If no signal is being input from the connected equipment or signal input is stopped while projecting, the “No signal” will appear.

•If a signal not supported by the projector is input, the “Unsupport signal” will appear.

•If an unavailable operation button is pressed, the icon will appear.

28

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Data Projector TDP-T9 Safety Precautions USA onlyBefore Using Power Sources Ventilation Important Safety InstructionsSource of Light Power-Cord Protection CleaningHeat Water and MoistureLightning storms Do not place the product verticallyObject and Liquid Entry Stack InhibitedDamage Requiring Service AccessoriesServicing Important Safety Instructions Replacement PartsSafety Check Do not use the product in a closed installation statePower Supply Cord Selection Important PrecautionsPlace and Manner of Installation Save Original Packing MaterialsExemption Clauses Important PrecautionsAvoid Volatile Liquid Other Cautions and Informations CopyrightsDisposal TrademarksRemote Control Batteries Contents Page Checking the package contents Names of each part on the main unit Names of each part on the control panel and remote control Label locations Parts on the rear panel Preparing and using the remote control Loading dry-cell batteries Into the remote controlOperating the remote control  Remove the battery cover  Insert the dry-cell batteriesConnecting a computer Operating a computerPlacement Styles PlacementFloor-mounted front projection Projection Distance and Size Screen As seen from above As seen from the sideConnection Before connectionTurning the power on and off Turning the power on Press the ON/STANDBY buttonTurning the power off Press the ON/STANDBY button Press the ON/STANDBY button againTurn on the power Select the language When using the first timeBasic operations Activate the connected deviceProjector placement angle adjustments Adjusting the screen size and focus To adjust the horizontal angle, use Tilt adjuster To stow the foot adjuster, hold up the projectorUsing handy features Using auto setting Only for analog input from computerPress the remote control’s Auto SET button Correcting the keystone distortionPassword function Cutting off the picture and sound temporarily MuteFreezing the image Freeze Key LockIf you forgot the password, please inquire your dealer Using handy featuresRe-enter the same password for confirmation Using the menus How to use the menusImage adjustment menu Detailed description Screen size Display setting menuBackground Using the menus Default setting menuDetailed description Fan mode Lamp powerDisplaying Information Status display B/P RWhen the lamp is broken Lamp replacementAbout lamp Lamp replacement Reset the lamp timer Used LampsLens cleaning Lens and main unit cleaningMain unit cleaning No power Power went out during useTrouble indications Lamp went out during use, or won’t come onBefore calling service personnel Specifications List of general specificationsSeparately sold product SpecificationList of supported signals RGB signals SpecificationsList of supported signals Video, S-Video signals List of supported signals Y/PB/PR signalsPin assignment of Computer in & Monitor terminals Control terminal Pin assignmentOthers
Top Page Image Contents