Toshiba TDP-T9 owner manual Displaying Information Status display, B/P R

Page 36

Using the menus (Continued)

■Displaying Information (Status display)

This displays information about the input signal, lamp use time, etc.

“Yes”: displayed, “No”: not displayed

	Item	Description	Computer	Y/PB/PR	Video	S-video
	Input	Input source name	Yes	Yes	Yes	Yes
	Resolution	Resolution (in dots)	Yes	No	No	No
	Video mode	Color method of video signal	No	Yes	Yes	Yes
	Picture mode	A group of Pre-set display mode	Yes	Yes	Yes	Yes
	Lamp time	Time of lamp use [Note 3]	Yes	Yes	Yes	Yes
	Version	Firmware version [Note 4]	Yes	Yes	Yes	Yes

Notes

1:The mode of supported RGB signals p.44 is shown.

2:Sync signal polarity shown as P (positive) or N (negative) for [H/V].

3:Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be used as a counter of guaranteed lamp time.) When the displayed time approaches 2,000 hours, consult with a store about getting a TLPLV6 replacement lamp (sold separately) prepared.

4:[Version] shows the version of the projector’s internal control program. This version is referred to for customer service, etc.

36

Image 36

Contents Data Projector TDP-T9 Safety Precautions USA onlyBefore Using Important Safety Instructions Power Sources VentilationSource of Light Power-Cord Protection CleaningHeat Water and MoistureLightning storms Do not place the product verticallyObject and Liquid Entry Stack InhibitedAccessories Damage Requiring ServiceServicing Important Safety Instructions Replacement PartsSafety Check Do not use the product in a closed installation statePower Supply Cord Selection Important PrecautionsPlace and Manner of Installation Save Original Packing MaterialsImportant Precautions Exemption ClausesAvoid Volatile Liquid Other Cautions and Informations CopyrightsDisposal TrademarksRemote Control Batteries Contents Page Checking the package contents Names of each part on the main unit Names of each part on the control panel and remote control Label locations Parts on the rear panel Preparing and using the remote control Loading dry-cell batteries Into the remote controlOperating the remote control  Remove the battery cover  Insert the dry-cell batteriesConnecting a computer Operating a computerPlacement Placement StylesFloor-mounted front projection Projection Distance and Size Screen As seen from above As seen from the sideConnection Before connectionTurning the power on and off Turning the power on Press the ON/STANDBY buttonTurning the power off Press the ON/STANDBY button Press the ON/STANDBY button againTurn on the power Select the language When using the ﬁrst timeBasic operations Activate the connected deviceProjector placement angle adjustments Adjusting the screen size and focus To adjust the horizontal angle, use Tilt adjuster To stow the foot adjuster, hold up the projectorUsing handy features Using auto setting Only for analog input from computerPress the remote control’s Auto SET button Correcting the keystone distortionPassword function Cutting off the picture and sound temporarily MuteFreezing the image Freeze Key LockUsing handy features If you forgot the password, please inquire your dealerRe-enter the same password for conﬁrmation Using the menus How to use the menusImage adjustment menu Display setting menu Detailed description Screen sizeBackground Using the menus Default setting menuDetailed description Fan mode Lamp powerDisplaying Information Status display B/P RLamp replacement When the lamp is brokenAbout lamp Lamp replacement Reset the lamp timer Used LampsLens and main unit cleaning Lens cleaningMain unit cleaning No power Power went out during useTrouble indications Lamp went out during use, or won’t come onBefore calling service personnel Speciﬁcations List of general speciﬁcationsSeparately sold product SpeciﬁcationList of supported signals RGB signals SpeciﬁcationsList of supported signals Y/PB/PR signals List of supported signals Video, S-Video signalsPin assignment of Computer in & Monitor terminals Control terminal Pin assignmentOthers