Toshiba TLP780E Turning the power off, Press ON/STANDBY after using the projector, Control panel

Page 33

Turning the power off

CONTENTS

33

Remote control

INPUT		ON/STANDBY	1,2
	LASER
KEYSTONE	AUTO	SET
KEYSTONE		SET

L-CLICKR-CLICK

1

2

ON/STANDBY

ON/STANDBY

ON/STANDBY

ON/STANDBY

Press ON/STANDBY after using the projector.

An instruction message for turning the power off appears on the screen and disappears after a while. When the message disappears, operation becomes invalid.

Press ON/STANDBY again.

Cooling starts. Once cooling is completed, the LAMP and FAN indicators turn off and the standby mode is set. (The ON indicator turns in orange.)

VOLUME/ADJUST

MENU ENTER EXIT

	ON	LAMP
	ON	(Green)
		(Green)
	(Orange) Flashing
		FAN

A (Green)

LAMP

ON

(Off) (Orange)

B

FAN

(Green)

LAMP

ON

(Off) (Orange)

C

FAN

(Off)

Operations

PIP FREEZE

RESIZE

CALL MUTE

Control panel

(Main unit side)

2

A	To protect the light source lamp, the LAMP indicator blinks as long as
	a minimum of cooling is necessary. The power cannot be turned back

	on during this time. Unplugging the power cord at this time will shorten
	the lamp’s duration life.
	The cooling fan continues to run for a while to expel the heat remaining
B
	inside. If you are in a hurry, however, you may unplug the power cord
	at this time.
	The standby mode is set.

1,2				ON
1,2
				R
			TE
			EN
			U
			N
			E
			M
	P	U	T
IN		U

LAMP

ON / STANDBY

TEMP

VOL / ADJ

Indicators

FAN

EXIT

A
UT
O	S
	ET

K

E

Y

S

T

O

N

E

C

Notes

•The projector consumes about 20W of power in the standby mode. We recommend you unplug the power cord when not using the projector for long periods of time.

•Be sure that the LAMP indicator has turned off before unplugging the power cord. Cutting the power by unplugging the power cord while the projector is operating or the light source lamp is being cooled will shorten the lamp’s duration life. Should a fault or some other irregularity arise with this unit, unplug the power cord.

•When reinserting the power plug before the lamp has cooled, please wait until the lamp has cooled sufficiently before use. When the lamp is at a high temperature, it may not light and it’s life duration will be shortened.

Image 33

Contents TLP780E TLP781E Safety Precautions Save Original Packing Materials Avoid Volatile LiquidMoisture Condensation Power Sources Source of LightVentilation Important Safety Instructions Object and Liquid Entry AccessoriesDo not place the product vertically Stack InhibitedReplacement Parts Damage Requiring ServiceSafety Check ServicingDo not move the projector while the arm is still erect Do not carry by the camera armDo not look into the arm light while it is lit Strong light may cause damage to your eyes or sightPower supply cord selection Contents Names of each part on the main unit Explanation here is only for the model without the documentRefer to Names of each part on the main unit Top sideMenu button Input button Right side Names of each part on the remote control Loading batteries Install the batteriesOpen the cover Attach the coverRemote control operation Front sideRear side Viewer Floor-mounted projector placementDetermine the screen size projected on the screen Top viewSide view Light Orange Power cord Supplied Connect the power cordTake off the lens cover Insert the other end into a wall outletFoot adjuster Foot adjuster release button Projector placement angle adjustmentLift up Lower Turn clockwise to lift up Turn counterclockwise to lowerViewer Translucent screen Ceiling-mounted projector placementConnecting a computer Computer in 1 connector Connecting a computer Computer in 2 connector Connecting video equipment Connectionsand Computer Projector operation control by a computerHow to use the output connector Projection on the screen Remote controlPress ON/STANDBY Lamp lights and the start up display appearsPress Enter to confirm Turn on the connected equipment and put it in playback modeControl panel Main unit side LanguagePress Input and hold for two seconds Select the input source by pressing Input repeatedlyPress Enter Input source selection menu appearsFocusing ring Adjust the picture size by turningStill picture is recommended for focusing Zooming leverAbout the LCD Panel Press VOL/ADJ +/- to adjust volumePress ON/STANDBY after using the projector Turning the power offPress ON/STANDBY again Control panelInput full screen video signals from the input Adjusting the picture automaticallySource computer and project the image Press Auto SETCorrecting the keystone distortion Press KeystoneConfirm the keystone distortion After confirming that V-keystone is selected on the menu Keystone adjustment finishesCutting off the picture and sound temporarily Icon appears in the mute modePress Mute Sound and picture are cut off temporarilyFreezing the picture Icon appears in the freeze modePress Freeze Picture freezesIcon appears in the resize mode Enlarging the picture sizePress Resize Displaying PIP Sub-pictures Press PIPSub-picture is displayed Press Call Displaying InformationOperating a computer by the remote control Press Menu Operating the menu screenPress Menu once again Select the item with the selection ButtonsSelect the item with selection buttons Adjust with VOL/ADJ +Enter Press Enter Press EnterShutter Guide Menu adjustments and settingsFull Menu adjustments and settings Picture Full Menu adjustments Position Full Menu adjustments Color Full Menu adjustments and settings Audio Settings Adjustments Full Menu adjustments and settings DisplayFull Menu settings Default setting Reset all Full Menu settings ResetPIP menu setting ImagingDocument camera Preparation of the document imaging camera Press ARM Light Set a document to be projectedCamera head over them Move the camera head to adjust the size of the picture Press Camera to select the camera input modePress Camera Gain +/- to improve view of a When finished, turn off the light and close itCamera subject which is too dark or vivid Put back the armOverlaying projection Locking the white balance Balance Press W.BALANCE to turn the Lock indicatorProject a white paper and enlarge it to fill ScreenWith the document camera operating, fully Correcting illuminated defectsCover the camera lens with a piece of black Paper or clothMain unit side Trouble indicationsUnplug the power cord Take off the air filter cover Air filter cleaningClean the air filter Detach the air filterAssemble the air filter Mount the air filter coverAir filter Air filter cover Cleaning the lens Lens and main unit cleaningCleaning the main unit Replacing the intake, exhaust fans and air filterUnplug the power cord Wait until the lamp gets cool enough Lamp replacementTake off the lamp cover on the bottom panel Pull out the lampLoad a new lamp Reset the lamp timerAttach the lamp cover Slide the cover into place and tighten the two screwsSymptom Cause Correction Before calling service personalBefore calling service personal Do not connect anything Mini D-sub 15pin ConnectorApplicable computer signal Applicable signalSignal Timing Horizontal Signal Timing Vertical Timing chartApplicable signal Compatible Video and S-Video signalCompatible components video signal Y/PB/PR Controlling the projector by using RS-232C Signal assignment of RS-232C Interface formatCommand list Controlling the projector by using RS-232C VCL MO0 MS0 PIP Main unit SpecificationsLiquid crystal display Projection lensAccessories SpecificationsReplacement lamp Sold separately