Toshiba TLP780E Lamp replacement, Unplug the power cord Wait until the lamp gets cool enough

Page 66

Lamp replacement

CONTENTS

66

The lamp will eventually begin to project dark or dull pictures and finally will not light up. (Lamp’s life depends on operating conditions.) In such a case, replace the lamp with new one.

CAUTION

1 Unplug the power cord.

2 Wait until the lamp gets cool enough.

•If you use the projector mounted on the ceiling, ask the dealer to carry out the maintenance such as cleaning or replacement of the lamp.

•When replacing, always use lamp “TLPL78” (sold separately). For details, refer to the lamp instruction.

•If you have been using the projector, the lamp will be very hot, and may cause burn injuries. Wait for the lamp to cool (for longer than 1 hour) before replacing it.

•If the lamp should break, please handle with care to avoid injury due to broken pieces and contact your dealer for repair service.

3

1

2

Take off the lamp cover on the bottom panel.

Loosen the two screws, and pull off the lamp cover.

Lamp cover

	4	1		Pull out the lamp.
			2	Loosen the two fixing screws, and lift up the

handle to pull out the lamp.

Continued

Maintenance

Image 66

Contents TLP780E TLP781E Safety Precautions Save Original Packing Materials Avoid Volatile LiquidMoisture Condensation Power Sources Source of LightVentilation Important Safety Instructions Do not place the product vertically AccessoriesObject and Liquid Entry Stack InhibitedSafety Check Damage Requiring ServiceReplacement Parts ServicingDo not look into the arm light while it is lit Do not carry by the camera armDo not move the projector while the arm is still erect Strong light may cause damage to your eyes or sightPower supply cord selection Contents Names of each part on the main unit Explanation here is only for the model without the documentRefer to Names of each part on the main unit Top sideMenu button Input button Right side Names of each part on the remote control Open the cover Install the batteriesLoading batteries Attach the coverRemote control operation Front sideRear side Floor-mounted projector placement ViewerDetermine the screen size projected on the screen Top viewSide view Take off the lens cover Connect the power cordLight Orange Power cord Supplied Insert the other end into a wall outletLift up Lower Projector placement angle adjustmentFoot adjuster Foot adjuster release button Turn clockwise to lift up Turn counterclockwise to lowerCeiling-mounted projector placement Viewer Translucent screenConnecting a computer Computer in 1 connector Connecting a computer Computer in 2 connector Connecting video equipment Connectionsand Projector operation control by a computer ComputerHow to use the output connector Press ON/STANDBY Remote controlProjection on the screen Lamp lights and the start up display appearsControl panel Main unit side Turn on the connected equipment and put it in playback modePress Enter to confirm LanguagePress Enter Select the input source by pressing Input repeatedlyPress Input and hold for two seconds Input source selection menu appearsStill picture is recommended for focusing Adjust the picture size by turningFocusing ring Zooming leverPress VOL/ADJ +/- to adjust volume About the LCD PanelPress ON/STANDBY again Turning the power offPress ON/STANDBY after using the projector Control panelSource computer and project the image Adjusting the picture automaticallyInput full screen video signals from the input Press Auto SETCorrecting the keystone distortion Press KeystoneConfirm the keystone distortion Keystone adjustment finishes After confirming that V-keystone is selected on the menuPress Mute Icon appears in the mute modeCutting off the picture and sound temporarily Sound and picture are cut off temporarilyPress Freeze Icon appears in the freeze modeFreezing the picture Picture freezesIcon appears in the resize mode Enlarging the picture sizePress Resize Displaying PIP Sub-pictures Press PIPSub-picture is displayed Displaying Information Press CallOperating a computer by the remote control Press Menu once again Operating the menu screenPress Menu Select the item with the selection ButtonsEnter Press Enter Adjust with VOL/ADJ +Select the item with selection buttons Press EnterGuide Menu adjustments and settings ShutterFull Menu adjustments and settings Picture Full Menu adjustments Position Full Menu adjustments Color Full Menu adjustments and settings Audio Full Menu adjustments and settings Display Settings AdjustmentsFull Menu settings Default setting Full Menu settings Reset Reset allPIP menu setting ImagingDocument camera Preparation of the document imaging camera Press ARM Light Set a document to be projectedCamera head over them Press Camera to select the camera input mode Move the camera head to adjust the size of the pictureCamera subject which is too dark or vivid When finished, turn off the light and close itPress Camera Gain +/- to improve view of a Put back the armOverlaying projection Project a white paper and enlarge it to fill Balance Press W.BALANCE to turn the Lock indicatorLocking the white balance ScreenCover the camera lens with a piece of black Correcting illuminated defectsWith the document camera operating, fully Paper or clothTrouble indications Main unit sideClean the air filter Air filter cleaningUnplug the power cord Take off the air filter cover Detach the air filterAssemble the air filter Mount the air filter coverAir filter Air filter cover Cleaning the main unit Lens and main unit cleaningCleaning the lens Replacing the intake, exhaust fans and air filterTake off the lamp cover on the bottom panel Lamp replacementUnplug the power cord Wait until the lamp gets cool enough Pull out the lampAttach the lamp cover Reset the lamp timerLoad a new lamp Slide the cover into place and tighten the two screwsBefore calling service personal Symptom Cause CorrectionBefore calling service personal Mini D-sub 15pin Connector Do not connect anythingSignal Timing Horizontal Signal Timing Vertical Applicable signalApplicable computer signal Timing chartApplicable signal Compatible Video and S-Video signalCompatible components video signal Y/PB/PR Controlling the projector by using RS-232C Signal assignment of RS-232C Interface formatCommand list Controlling the projector by using RS-232C VCL MO0 MS0 PIP Liquid crystal display SpecificationsMain unit Projection lensReplacement lamp SpecificationsAccessories Sold separately