Toshiba GN-1060 manual Specify Ssid, Selecting the Ssid from the available network list

Page 18

1 SETTING UP WIRELESS NETWORK

Specify SSID

When you select the Infrastructure Mode for the network type, you can specify the SSID by selecting the available network list or manually entering the SSID.

P.16 “Selecting the SSID from the available network list”

P.17 “Entering the SSID manually”

If you are not sure how the SSID must be specified, see the following section to determine the SSID. P.11 “Determine the SSID”

Selecting the SSID from the available network list

This equipment can search the available SSID automatically from the wireless network. Then you can select the SSID from the list.

1 Press [AVAILABLE NETWORK].

The AVAILABLE NETWORK screen is displayed.

2 Select the SSID that this equipment will connect and press [OK].

The screen returns to the SSID SETTINGS screen.

yThe available network may not be displayed according to the communication environmental conditions.

yIf the desired SSID is not displayed, please specify the SSID manually.

P.17 “Entering the SSID manually”

yThis Wireless LAN supports only channel 1 to 11. This equipment cannot connect the Access Point that uses the other channel than these channels. Please make sure to set the channel between 1 to 11 in the Access Point.

16 Setting Up the Infrastructure Mode

Image 18

Contents Operators Manual for Wireless LAN Module Page ‰ Model and series names in this manual „ How to read this manual ‰ Symbols in this manualPreface ‰ Options‰ Trademarks „ About Toshiba Wireless Solution Precautions„ Precautions for Use ‰ Wireless Interoperability‰ Europe EU Declaration of Conformity ‰ Regulatory Information‰ Canada Industry Canada IC EN 300‰ USA-Federal Communications Commission FCC Labelling‰ Regulatory Notice for Channel Use in France „ NotesContents Contents Setting up the Ad Hoc Mode Before Setting Up Wireless NetworkSetting Up the Infrastructure Mode Disabling Wireless NetworkInfrastructure Mode Before Setting Up Wireless Network„ Planning for installation Ad Hoc Mode‰ Determine the security mode ‰ Determine the SsidWPA/WPA2/802.1X WEP Enter the administrator password and press OK Setting Up the Infrastructure ModePress Password „ Select network typePress Wireless Setting Press on and press NextSetting Up the Infrastructure Mode „ Specify Ssid ‰ Selecting the Ssid from the available network listPress Available Network ‰ Entering the Ssid manually Press SsidScreen returns to the Ssid Settings screen „ Select security mode Press WPA, WPA2 or 802.1X, and then NextPress EAP-TLS and press Next Press Disable and press EAP User Name Press NextSpecify the following items and press Next Encryption Between AP and STAConfirm the settings and press Finish Press YES, and wait until the setting is reflected‰ Selecting WPA/WPA2/802.1X security mode with Peap protocol Press Peap and press NextEnter the following items and press Next EAP User NameConfirm the settings and press Finish ‰ Selecting WPAPSK/WPA2PSK security mode Press Wpapsk or WPA2PSK and press NextSpecify the following items and press Next ‰ Selecting WEP security mode Press WEP button and press NextSpecify the following items and press Next ‰ Selecting no security mode Press None and press NextPress YES, and wait until the setting is reflected Setting up the Ad Hoc Mode Wireless Setting screen is displayed Press AD HOC and press Next „ Specify Ssid Wireless LAN Security Settings screen is displayed Press WEP and press Next Select the transmit power and press Next Select the transmit power and press Next button Confirm the settings and press Finish buttonPress YES, and wait until the setting is reflected Disabling Wireless Network Press Password buttonPress OFF and press Next Specification Troubleshooting Glossary AppendixSpecification DescriptionTroubleshooting When Error Messages are DisplayedWhen Cannot Connect to Toshiba MFP Glossary Index NumericsIndex GN-1060 OME100082C0 GN-1060