Toshiba GN-1060 manual Specification, Description

Page 46

2 APPENDIX

Specification

Item	Description

Transmission Format	IEEE 802.11b/g standard
	Direct Sequence Spread Spectrum (DSSS)
	Orthogonal Frequency Division Multiplexing (OFDM)

Data Transmission Speed	54, 24, 11, 5.5, 2, 1 Mbps (automatic)

Access Method	CSMA/CA

Transmission Packet	IEEE 802.11g frame

Wireless Category	Low-power data transmission system (2400 to 2472 MHz)

Aerial Power	10 mW/MHz or below

Security	Static WEP
	Key Length: 64 bit, 128 bit, 152 bit
	WPA/WPA2: PSK (TKIP, AES(CCMP))
	WPA/WPA2: TLS/PEAP (TKIP, AES(CCMP))
	802.1X: TLS/PEAP (DYNAMIC WEP)
	TLS supported RADIUS server
	Steel-belted Radius
	Windows Server 2003/Windows Server 2008
	PEAP supported RADIUS server
	Windows Server 2003/Windows Server 2008

Operation Mode	Infrastructure Mode, Ad Hoc Mode

Wireless ON/OFF	Available

Wired LAN/Wireless LAN	Not Available
Simultaneous Operation

Wireless LAN/Bluetooth	Available
Simultaneous Operation

44 Specification

Image 46

Contents Operators Manual for Wireless LAN Module Page ‰ Model and series names in this manual „ How to read this manual ‰ Symbols in this manualPreface ‰ Options‰ Trademarks „ About Toshiba Wireless Solution Precautions„ Precautions for Use ‰ Wireless Interoperability‰ Europe EU Declaration of Conformity ‰ Regulatory Information‰ Canada Industry Canada IC EN 300‰ USA-Federal Communications Commission FCC Labelling‰ Regulatory Notice for Channel Use in France „ NotesContents Contents Setting up the Ad Hoc Mode Before Setting Up Wireless NetworkSetting Up the Infrastructure Mode Disabling Wireless NetworkInfrastructure Mode Before Setting Up Wireless Network„ Planning for installation Ad Hoc Mode‰ Determine the Ssid ‰ Determine the security modeWPA/WPA2/802.1X WEP Enter the administrator password and press OK Setting Up the Infrastructure ModePress Password „ Select network typePress Wireless Setting Press on and press NextSetting Up the Infrastructure Mode ‰ Selecting the Ssid from the available network list „ Specify SsidPress Available Network ‰ Entering the Ssid manually Press SsidScreen returns to the Ssid Settings screen Press WPA, WPA2 or 802.1X, and then Next „ Select security modePress EAP-TLS and press Next Press Disable and press EAP User Name Press NextSpecify the following items and press Next Encryption Between AP and STAConfirm the settings and press Finish Press YES, and wait until the setting is reflected‰ Selecting WPA/WPA2/802.1X security mode with Peap protocol Press Peap and press NextEnter the following items and press Next EAP User NameConfirm the settings and press Finish ‰ Selecting WPAPSK/WPA2PSK security mode Press Wpapsk or WPA2PSK and press NextSpecify the following items and press Next ‰ Selecting WEP security mode Press WEP button and press NextSpecify the following items and press Next ‰ Selecting no security mode Press None and press NextPress YES, and wait until the setting is reflected Setting up the Ad Hoc Mode Wireless Setting screen is displayed Press AD HOC and press Next „ Specify Ssid Wireless LAN Security Settings screen is displayed Press WEP and press Next Select the transmit power and press Next Select the transmit power and press Next button Confirm the settings and press Finish buttonPress YES, and wait until the setting is reflected Disabling Wireless Network Press Password buttonPress OFF and press Next Specification Troubleshooting Glossary AppendixSpecification DescriptionWhen Error Messages are Displayed TroubleshootingWhen Cannot Connect to Toshiba MFP Glossary Index NumericsIndex GN-1060 OME100082C0 GN-1060