Toshiba GN-1060 manual Selecting WPA/WPA2/802.1X security mode with Peap protocol

Page 25

1 SETTING UP WIRELESS NETWORK

Selecting WPA/WPA2/802.1X security mode with PEAP protocol

Using the WPA/WPA2/802.1X with the PEAP protocol, you must install the CA certification file in the equipment. This equipment uses the user name and password to authenticate the access rights to the wireless network, and the RADIUS server authenticate this equipment using the CA certification file.

When using the WPA/WPA2/802.1X with the PEAP protocol, you must install the CA certification file in the equipment using TopAccess first. For instructions on how to install the CA certification using TopAccess, refer to TopAccess Guide.

1 Press [WPA], [WPA2] or [802.1X], and then [NEXT].

The AUTHENTICATION SETTINGS screen is displayed.

To select [TKIP] or [AES (CCMP)], press [WPA] or [WPA2], or to select [DYNAMIC WEP], press [802.1X].

2 Press [PEAP] and press [NEXT].

The WIRELESS AUTHENTICATION (PEAP) screen is displayed.

Setting Up the Infrastructure Mode 23

Image 25

Contents Operators Manual for Wireless LAN Module Page Preface „ How to read this manual ‰ Symbols in this manual‰ Model and series names in this manual ‰ Options‰ Trademarks „ Precautions for Use Precautions„ About Toshiba Wireless Solution ‰ Wireless Interoperability‰ Canada Industry Canada IC ‰ Regulatory Information‰ Europe EU Declaration of Conformity EN 300Labelling ‰ USA-Federal Communications Commission FCC„ Notes ‰ Regulatory Notice for Channel Use in FranceContents Contents Setting Up the Infrastructure Mode Before Setting Up Wireless NetworkSetting up the Ad Hoc Mode Disabling Wireless Network„ Planning for installation Before Setting Up Wireless NetworkInfrastructure Mode Ad Hoc Mode‰ Determine the Ssid ‰ Determine the security modeWPA/WPA2/802.1X WEP Press Password Setting Up the Infrastructure ModeEnter the administrator password and press OK „ Select network typePress on and press Next Press Wireless SettingSetting Up the Infrastructure Mode ‰ Selecting the Ssid from the available network list „ Specify SsidPress Available Network Press Ssid ‰ Entering the Ssid manuallyScreen returns to the Ssid Settings screen Press WPA, WPA2 or 802.1X, and then Next „ Select security modePress EAP-TLS and press Next Press Next Press Disable and press EAP User NameEncryption Between AP and STA Specify the following items and press NextPress YES, and wait until the setting is reflected Confirm the settings and press FinishPress Peap and press Next ‰ Selecting WPA/WPA2/802.1X security mode with Peap protocolEAP User Name Enter the following items and press NextConfirm the settings and press Finish Press Wpapsk or WPA2PSK and press Next ‰ Selecting WPAPSK/WPA2PSK security modeSpecify the following items and press Next Press WEP button and press Next ‰ Selecting WEP security modeSpecify the following items and press Next Press None and press Next ‰ Selecting no security modePress YES, and wait until the setting is reflected Setting up the Ad Hoc Mode Wireless Setting screen is displayed Press AD HOC and press Next „ Specify Ssid Wireless LAN Security Settings screen is displayed Press WEP and press Next Select the transmit power and press Next Confirm the settings and press Finish button Select the transmit power and press Next buttonPress YES, and wait until the setting is reflected Press Password button Disabling Wireless NetworkPress OFF and press Next Appendix Specification Troubleshooting GlossaryDescription SpecificationWhen Error Messages are Displayed TroubleshootingWhen Cannot Connect to Toshiba MFP Glossary Numerics IndexIndex GN-1060 OME100082C0 GN-1060