Toshiba 1000 Series manual Procedure for Defective Product Screening and Disposition

Page 58

Procedure for Defective Product Screening and Disposition

User must contact TIC via e-mail upsservice@tic.Toshiba.com, or phone 1-877-867- 8773 (outside the U.S. call 713-466-0277) to report a defect in a UPS, UPS part, and/or BATTERY. Subject to the limitations of TIC policy and product type, TIC service, or TIC service representative shall repair/replace the UPS/part warranted hereunder, without charge for material or labor. If TIC determines that the requested repair is not covered under this limited warranty policy, TIC shall advise customer and quote cost of repair. Repair charges shall be based on service parts price and prevailing service charges at the time of repair. In no event after the expiration of

the respective warranty period will warranty work be performed.

In the event of a defective BATTERY claim (stand-alone and/or cabinet) TIC will use its published Battery Diagnostic Document to evaluate warranty applicability. TIC will confirm that the storage, maintenance, installation, and operating conditions were met. The BATTERY capacity will be tested in accordance with the “performance test” guidelines IEEE STD 450. Should the BATTERY fail to deliver 70% of its rated capacity it shall be deemed defective and will be replaced. Either float or cyclic service will be used to determine the warranty credit (as per published Battery Diagnostic Document). The typical credit applied will be as listed in the following table.

Credit for Replacement Battery When Approved Warranty

Time from Shipment

UPS Batteries

Cost to Customer

(months)

% Credit

% List Price

0-24

100

0

25-30

55

45

31-36

45

55

37-42

35

65

43-48

25

75

49-54

15

85

55-60

5

95

36

Image 58
Contents Page Important Notice Uninterruptible Power Supply Table of Contents Manual’s Purpose and Scope Page FCC Part EMC StatementsICES-003 Declaration of Conformity Request General Safety Instructions Safety Alert Symbol / Signal WordsPage Special Symbols Qualified Personnel only Important Safety InstructionsQualified Personnel shall XII Important Safety Instructions contd XIV Instructions Importantes Concernant LA Sécurité Conserver CES InstructionsInspection/Storage/Disposal Storage Maintenance DisposalInstallation Precautions Conductor Routing and Grounding Operating Precautions XXI Introduction System DescriptionBlock diagram General DescriptionPage Free Run Mode Diagnostic TestsSystem Configuration Storage Installation EnvironmentVertical and Wall-mounted Installations with Accessories Rack-mounted Installation with Accessories Stacked UPS Installation with accessories Rear Panel Views 1000VA 1200VA Tower Rear Panel 1000VA Rack mount 1U Rear Panel 1000VA Rack mount 2U Rear Panel Connection to main supply and loads 1000 1200 VA Example of Installation of Plug & Play products Front Panel Settings Settings Options Default RemarksBattery Test TEST? Computer and Alarm Connections RS-232 Standard Interface PortNetwork Transient Protector EPO Port emergency power offUSB Port Load SegmentsShutting Down the UPS User’s Guide to OperationsUPS Startup and Shutdown Starting the UPS Button OperationControl Panel functions ON-LINEUPS Meters Display Normal DisplayLCD Message Description UPS Configurations UPS Manual Test Audible AlarmsSilencing an Alarm Interpreting UPS MessagesTroubleshooting Maintenance Input Technical SpecificationsPower Range 1000-1200 VA LV General OutputPower Range1000 VA 19 Rack-mount model, LV, 1U & 2U General EnvironmentalPower Range 1000-1200 VA HV General Power Range 1000 VA 19 Rack-mount model, HV, 1U & 2U General StandardTower HV Model Rack-mount HV ModelTower LV Model Rack-mount LV ModelWarranty Information Uninterruptible Power SUPPLIES-UPSLimitations and Exclusions Page Procedure for Defective Product Screening and Disposition Respective warranty period will warranty work be performedModifications