Siemens M1 manual Memory commands, AT&Dn Data Terminal Ready DTR options, Data flow control

Page 29

Technical reference section

AT&Dn - Data Terminal Ready (DTR) options

AT&Dn

[n=0..3]

 

 

Option

Result

 

 

AT&D0

The GSM module ignores the status of the DTR control line connected

 

to the COM interface.

 

 

AT&D1

When the DTR line switches from ON to OFF, the GSM module changes

 

to command mode. The existing connection to the distant station is not

 

cleared down.

 

 

AT&D2

When the DTR line switches from ON to OFF, the GSM module sets up

 

a connection to the distant station, switches to command mode and

 

deactivates auto-answer mode. Auto-answer can be reactivated by

 

resetting DTR to ON.

 

 

AT&D3

The transition of DTR to OFF has the same effect as an AT&F command,

 

i.e. the factory configuration is loaded. An existing connection to the dis-

 

tant station is cleared down.

 

 

Data flow control

Even if your PC is set, for example, to 19200 baud, the maximum GSM rate that can be used is 9600 bit/s. A higher setting causes the GSM module to receive more data from the PC than it can transfer to the GSM network. In order to prevent a data over- flow, it must be able to interrupt the data flow from the PC. This is accomplished by means of the RTS/CTS hardware data flow control, which switches over the COM in- terface so as to interrupt the RTS (computer) and CTS (GSM module) control lines.

Memory commands

The GSM module is equipped with a 128-byte nonvolatile RAM in which the values of the modifiable S-registers and other values are stored. This section describes the val- ues, how to store them and how to use them.

28

Page 28 Page 30
Image 29
Page 28 Page 30
Contents GSM Contents Technical reference section Contents General information Technical dataGSM documentation GSM Module M1 Product description FeaturesGSM Module M1 Description of the interfaces Hybrid connector manufacturer-specificSIM card InterfacePower supply / power consumption Installation / startup Mounting the moduleSwitching the GSM module on/off Cable assignmentSetting / testing the COM interface Installation / startupPower consumption Overvoltage / undervoltageATB7 Setting the GSM radio transfer rateATB13 AT+CPIN? Setting up and clearing down connections+CPIN SIM PIN AT+CPIN=1234ATH TroubleshootingAT&F System errors Connection cannot be set upOwn errors Cannot receive fax Incorrect characters on screenGSM module does not dial Overview of AT commands General AT commands SMS AT commands GSM Overview of AT commandsGSM AT commands GSM Connecting to your GSM module AT command line prefixCommand syntax of the AT standard Technical reference section AT standardATH ATS7?Q0E1 Technical reference sectionATD0123456789 AT&F0Connect ErrorRing No CarrierTransparent mode Command modeEscape command Operating modesATH Go on-hook ATOn Return to transparent modeSetting the transfer rate ATB99 ATBn Select GSM module’s operating modeATB ATD ATD Dial a telephone numberValid dial strings Dial ATD+4989telephone numberATD123456789 AT%Dn Automatic dialing with DTRAtdl AT&Z0=123456789ATA Answer a call Displaying and storing a configurationATS0=n Auto-answer mode Stored Profile AT&V Active ProfileTelephone Numbers &Z0= Z1= Z2= Z3=ATQn Activate and deactivate result codes ATEn Command echoScreen outputs Limits of screen outputs Control line options AT&Cn Data Carrier Detect DCD options ATXn Extended connect messageData flow control Memory commandsAT&Dn Data Terminal Ready DTR options AT&Zn=x Store telephone number AT&Wn Store configurationAT&Z0 = ATDS=n Dial stored telephone numberAT&Yn Configuration at power-up AT+C commands for GSMATZn Load user profile AT+CXXSN = ?+CGMI Siemens AT+CGMIAT+CGMM +CGMM M1AT+CHUP Hangup call AT+CEER Extended error reportAT+CGSN Request product serial number ID Enter AT+CMEE Report mobile equipment errorAT+CEER GSM moduleAT+CREG? +CME ErrorAT+CREG? AT+CREG Network registrationAT+COPS Operator selection EnterAT+CREG? GSM module +CREG 0,0 = not registeredAT+COPS? AT+COPS=?+COPS 0, 0, Operator Name AT+COPS?AT+COPS=? Display list of available network operators AT+COPS=?Privat TelekomAT+CPIN Enter PIN and query blocks AT+CPIN2 Enter PIN2 and query PIN2 blocks +CME Error Wrong PasswordAT+CPIN2=1234 AT+CPWD Change passwordAT+CPWD=? +CPWD SC,8,PS,8, P2,8Errors AT+CSQ Signal qualityAT+CSQ ReceiveAT+CKPD=? AT+CKPD Keypad controlAT+CKPD=? +CKPD 0123456789*#CDEISUXYZAT+CXXSN=? AT+CXXSN Single-numbering parameterizationAT+CXXSN=2 AT+CXXSN=?+CXXSN 0,1,2 AT+CXXMOC=1 AT+CXXMOC=?+CXXMOC 0,1 +CPBS MD , SM , OW , FD AT+CPBS Select phonebook memory storageAT+CPBS=? AT+CPBR=? AT+CPBR Read phonebook entriesAT+CPBR=? +CPBR index, number length, textAT+CPBW Write phonebook entry AT+CBST=? AT+CBST Select bearer service typeAT+CBST? AT+CRC? AT+CRC Cellular result codeAT+CRC=? AT+CRC?AT+CLIP? AT+CLIP Calling line identification presentationAT+CLIP=? AT+CLIP?AT+CPAS=? AT+CPAS Phone activity statusAT+CPAS=? +CPAS 0 1 2 3 4AT+FCLASS? AT+FCLASS Select modeAT+FCLASS=? AT+FCLASS=?AT+CXXCID=? AT+C commands for the short message service SMSAT+CXXCID Card identification Parameter command syntax AT+CSMS Select message serviceValues implemented AT+CPMS Preferred message storageAT+CMGF Message format AT+CSCA Service center addressIf PDU mode +CMGF=0 and command successful Action command syntaxIf PDU mode +CMGF=0 If send is successful AT+CMGR Read messageAT+CNMI New message indications AT+CMGW Write message to memoryAT+CMGD Delete message AT+CMGL List messages AT+CMS Error message service failure result codes+CMGL=? Value definitionsAT+FCR= AT+FAAAT+FBUF?AT+FBOR S-registersAT+FDT= EnterATS0?S7? ATSn? Read an S-registerATSn=x Write to an S-register ATS0=3Binary and decimal values in S-registers Decimal input and binary storage Bit position registersYou wish to enter the following parameter values OFF Overview of the S-registers Please noteDTR on OFF Technical reference section AT&T0 AT&T1ABC ATIn Display GSM module I-data Interface Technical data GeneralTechnical data Hybrid connector manufacturer-specific Fax Technical data GSM modesFAX G3 DataEuropean Telecommunications Standards Institute GSM documentation GSM reference documentsEtsi contact General information CE-Sign ServiceGeneral information

M1 specifications

The Siemens M1 is a prominent urban transit solution designed for efficient and sustainable public transportation systems. This innovative metro train has become a staple in various metropolitan areas, known for its balance of performance, safety, and passenger comfort.

One of the key features of the Siemens M1 is its modular design, which allows for flexibility in configuration depending on specific transit needs. The train typically consists of multiple carriages that can be adjusted for length and capacity, accommodating different passenger volumes while minimizing operational costs. This adaptability makes the M1 ideal for growing urban environments where ridership numbers can fluctuate.

The Siemens M1 is built with advanced technologies that enhance its operational efficiency. It utilizes a lightweight construction, primarily through the use of aluminum, which reduces energy consumption while still maintaining structural integrity and safety standards. The train is also equipped with cutting-edge traction systems that ensure smooth acceleration and fast braking, resulting in a comfortable ride for passengers.

Safety is a paramount concern in transit systems, and the M1 incorporates various safety technologies. It features advanced signaling systems that enhance communication between trains and trackside equipment. Moreover, the train is designed with anti-collision measures and real-time monitoring systems that can detect faults before they lead to service disruptions.

Passenger comfort is another critical aspect of the Siemens M1 design. The interiors are spacious and feature modern seating arrangements, allowing for easy movement within the train. Large windows provide natural light and views of the outside environment, contributing to a more pleasant travel experience. The train also offers features like climate control, information displays, and accessibility options for passengers with reduced mobility.

Environmental sustainability is an integral part of the Siemens M1’s design. It is tailored to reduce carbon emissions, featuring energy-efficient systems that lower the overall ecological footprint. Additionally, the train can be integrated with renewable energy sources, further promoting green public transport initiatives.

Overall, the Siemens M1 stands out as a versatile and efficient urban transit option, combining modern technology and design principles that cater to the needs of both operators and passengers. With its focus on safety, comfort, and sustainability, the Siemens M1 continues to play a vital role in shaping the future of urban mobility.
Top Page Image Contents