Siemens PCIL43 manual Safety Guidelines

Page 4

Safety Guidelines

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are graded according to the degree of danger.

Danger

indicates that death or severe personal injury will result if proper precautions are not taken.

Warning

indicates that death or severe personal injury may result if proper precautions are not taken.

Caution

with a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken.

Caution

without a safety alert symbol, indicates that property damage can result if proper precautions are not taken.

Notice

indicates that an unintended result or situation can occur if the corresponding information is not taken into account.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property damage.

Qualified Personnel

The device/system may only be set up and used in conjunction with this documentation. Commissioning and operation of a device/system may only be performed by qualified personnel. Within the context of the safety notes in this documentation qualified persons are defined as persons who are authorized to commission, ground and label devices, systems and circuits in accordance with established safety practices and standards.

Prescribed Usage

Note the following:

Warning

This device may only be used for the applications described in the catalog or the technical description and only in connection with devices or components from other manufacturers which have been approved or recommended by Siemens. Correct, reliable operation of the product requires proper transport, storage, positioning and assembly as well as careful operation and maintenance.

Trademarks

All names identified by ® are registered trademarks of the Siemens AG. The remaining trademarks in this publication may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in this publication is reviewed regularly and any necessary corrections are included in subsequent editions.

Siemens AG

Order No.: A5E00432875-01

Copyright © Siemens AG 2005.

Automation and Drives

Edition 09/2005

Technical data subject to change

Postfach 48 48

 

 

90437 NÜRNBERG

 

 

GERMANY

 

 

Image 4
Contents Simatic Operating Instructions Edition 09/2005Page Industrial PC Rack PC IL Operating Instructions Edition 09/2005Safety Guidelines Table of contents 10-1 Glossary Glossary-1 Table of contents Introduction PrefaceContents format Table of Contents Guide for the operating instructionsSafety information General safety instructionsRepairs System expansionsBattery ESD guidelinesDescription OverviewHighlights Areas of applicationHighlights General features FeaturesFunction Optional accessories InterfacesMonitoring functions Standard versionsDVD ROM Optional accessories Disk drivesOptional expansions Design External structureFront view of the device Pos Description Rear view of the device Pos DescriptionOperator controls Operator control on/off button Pos DescriptionConnecting elements InterfacesLayout of the interfaces on the rear of the device Pos Name DescriptionPower supply Position of the IEC power plug DescriptionStatus displays Status displays Display MeaningDescription 3.6 Design Deployment planning TransportUnpacking and checking the delivery unit Unpacking the deviceNoting the device identification data Device equipmentAmbient and environmental conditions Deployment planning Ambient and environmental conditions Installation Installing the devicePossible areas of installation Possible mounting methodsInstallation Installing the device Connecting Connecting peripheralsConnecting the device to power To be noted before you connect the deviceSteps for connecting the device to mains ConnectingLocalized information Secure the power plug Steps in securing the power plugCommissioning Basic commissioning initial power-upPrerequisites for commissioning Switch off the device Burner/DVD player softwareDVD burner Burner softwareRAID Software Sata interface Installation location Removable hard disksReplacing a hard disk SATA1RAID system 4MS08NVVFunctions for RAID system management Comments about faults Replace faulty drive in RAID systemSide panel Associate new hard drive Commissioning Ethernet IntegrationFurther information Integration Temperature monitoring/display Temperature monitoringFunctions Overview of the following monitoring functionsFan monitoring Watchdog WDFunction Expansions and configuration Open the deviceTools PreparationOpen the device Steps for opening the enclosure coverSteps for opening the device front Memory expansion Installing expansion cardsMemory expansion options Installing expansion modules Installing an expansion moduleSteps for installing an expansion module Installing disk drives Options of installing disk drivesInstalling and removing a disk drive or removable rack Pos DescriptionRemoving the drive carrier module Steps for removing the drive carrier moduleInstalling and removing a hard disk Disk drive or removable disk rack installationInstalling a disk drive Steps for installing a disk driveMaintenance and service Removing and installing hardware componentsRepairs Carrying out repairsReplacing the backup battery To be noted before you replace the batteryReplacing the battery Reconfiguring the Bios Setup DisposalRemoving the power supply module Removing the power supply moduleHow to remove the power supply module Removing the motherboard How to remove the motherboardRemoving the motherboard Remove filter and device fan Preparing for equipment fan exchangeRemove filter and fan StepsProcessor replacement Installing the fanHow to remove the processor Removing the processor11-7 Reinstalling the software General installation procedureRecovery CD Restore DVDBooting with the CD Recovery Installing WindowsRestoring the factory state Setting up the partitions for Windows operating systems Setting up partitionsInstalling Microsoft Windows operating systems Format primary partitionSetting up the language selection for Windows 2000 MUI Setting up the language selection for Windows 2000 MUIInstalling drivers and software Maintenance and service Reinstalling the software General problems TroubleshootingProblem Possible cause To correct or avoid error Problems when using modules of third-party manufacturers Technical data 13.1 General specificationsGeneral technical data SafetySpecial Features Climatic ConditionsMech. Ambient conditions MotherboardGraphics COM1Certifications Status displays LEDsPower requirements of components maximum values AC voltage supplyStandard system Output voltageTechnical data of the telescopic rails Dimensional drawings Dimensional drawing of the deviceDimensional drawing for the use of telescopic rails Dimensional drawing for the use of telescopic railsMotherboard Detailed descriptionsSystem resources Bios Setup Tab Option SettingGuidelines and declarations Certificates and approvals DIN ISO 9001 certificateSoftware License Agreement Certification for the USA, Canada and AustraliaEMC Service and support Further supportTraining center Technical SupportService & Support on the Internet Figure A-1 For the temperature range 5 to 35 C Retrofitting instructionsESD Guidelines What does ESD mean?Electrical charge Figure B-1 Electrostatic voltages on an operatorAbbreviations Abbreviation Term DefinitionCGA CLKCmos COAFAQ EideEisa EMMIDE IECIgbt IrdaPata PCIPcmcia PICSata ScsiSdram SelvVRM WAVWlan WWWAbbreviations Glossary Boot diskette BootingConfiguration files Configuration softwareDevice configuration ControllerDisc-at-once DriversFormatting Gender changerHard disks HubIT networks Legacy USB supportLicense key License key diskettePassword MotherboardOperating system Packet writingReset Restore CDPixel Remove module bracketSetup Bios Setup TroubleshootingSerial interface Session at onceWindows WlanGlossary-10 Index CD-R / CD-RWIndex Index VGA Page Siemens AG