Toshiba DP-1810 manual Left side / Inner side

Page 23

9.Drawer

Maximum 250 sheets of plain paper can be placed in one go.

10.Front cover

Open this cover when you replace the toner cartridge. P.85 “Replacing Toner Cartridge”

Left side / Inner side

11

10

1

9

8	2
8
7
6

5

4

3

1.Original glass

Use this to copy three-dimensional originals, book-type originals and special paper such as overhead transparencies or tracing paper, as well as plain paper.

P.40 “Placing Originals”

2.Control panel

Use this to perform copying, key in the copy quantity, or set other functions. P.24 “Control panel”

3.Toner cartridge

P.9 “Recommended toner cartridges”

P.85 “Replacing Toner Cartridge”

4.Power switch

Turn the power of the equipment ON or OFF with this. P.27 “Preparation 1 - Turning Power ON”

5.Paper exit stopper

Use this to prevent the exiting paper from falling. Open this when you make a large amount of copies on a larger size of paper (e.g. LD, LG).

6.AC-IN terminal

Use this to connect the co-packed power cable and the equipment.

Description of Each Component 21

Image 23

Contents Operators Manual for Copying Functions Page Preface PrefaceFCC Notice Before Reading This Manual How to read this manual Symbols in this manualTrademarks Description of original/paper directionContents When Message Lamp is Lit/Blinking Adjusting Density LevelSwitching Operation Sound On/Off Changing of the Enabled Energy Saving Mode105 Daily Inspection Cleaning charger Cleaning transfer chargerContents Toner remaining check function Toshiba Quality Is Second to NoneRecommended toner cartridges Cartridge detecting functionGeneral Supplies / PartsToner When installing or moving General Precautions31.5 Other pointsWhen using the equipment Position of Certification label, etc When handling supplies During maintenance or inspectionFirst-aid measures Poration Disclaimer NoticeEnvironmental Information Energy saving featuresLow power mode Sleep mode / Super sleep modePreparation 2 Placing Copy Paper Preparation 1 Turning Power onDescription of Each Component Automatic Document Feeder optional, MR-2020 Description of Each ComponentFront / Right side Platen Cover optional, KA-1650PCLeft side / Inner side Platen sheet USB terminal 4-pinReceiving tray Scanning area Original scaleConfiguration of options Control panel Interrupt button/lamp Original mode button/lampsDensity adjustment buttons/lamps Original setting lampAPS/AMS selecting button/lamps Copy button/lampsOriginal button/lamps Press the power switch to on side Preparation 1 Turning Power onTurning power on Turning power OFFCanceling conditions for energy saving mode Saving energy when not in use Energy saving modeTypes of energy saving mode To turn the equipment into the energy saving mode manuallySuper sleep mode Feeder Media type Paper size Maximum sheet Capacity *1 Preparation 2 Placing Copy PaperAcceptable media types Media type Product name Recommended paperPaper types not acceptable Storing paperPress down the paper plate Placing paper in drawersWiden the gap with both hands Place paper in the drawer Adjust the side guides to the desired paper sizeRegister the paper size into the equipment Do not let your fingers be caught when closing the drawerRegistering standard size LD, LT, LT-R, LG, ST-R Preparation 3 Registering Size of Paper PlacedCode No Registering other standard sizesPress the Start button Making Copies Using Bypass TrayPlacing Originals Maximum number of originals scanned in one go Setting position Type of origiPlacing Originals Acceptable originalsPlacing originals on the original glass Placing booklet-type originals such as books or catalogs Media types Maximum size Maximum number Paper weight Using Automatic Document Feeder optionalPrecautions for Automatic Document Feeder optional When black streaks appear on the copied imagePlacing originals on Automatic Document Feeder optional When placing a large amount of originals with a long widthSelect the copy modes as required Making CopiesCheck if paper is placed in the drawer Place the originalPress the CLEAR/STOP button during scanning or copying When the number of sheets exiting has exceededWhen the paper has run out Stopping/Resuming copyingPress the Interrupt button Interrupting copying and making another copy Interrupt copyMedia type Paper size Maximum sheet Capacity *1 Using Bypass TrayBypass copying Paper size has been registered Placed on the bypass tray is litAutomatic paper selection APS Manual paper selection Default Settings Paper SelectionZooming In/Out Copy Image Contents Default setting at installation Default SettingsAutomatic paper selection APS Paper SelectionAutomatic paper selection APS Place the original on the Automatic Document FeederPlace paper in the drawer Place the original Manual paper selectionSelecting the drawer of the equipment Specifying reproduction ratio manually Zooming In/Out Copy ImageAutomatic magnification selection AMS Automatic magnification selection AMSIf the Function Clear lamp is blinking and copying stops Specifying both the sizes of the original and the copy paper Zooming in button until Specifying reproduction ratio manuallyPress Zooming out or Desired reproduction ratio appearsZooming In/Out Copy Image Press the Sort button Copying in Same Page Order as Originals Sort CopyingRepeat this until all originals have been scanned Sort buttonButton Original is scannedCopying Both Sides of Card into 1 Page ID Card Page Selecting Image Mode Dark Adjusting Density LevelTo adjust the density to the desired level To return it to the automatic copy density modeSettings and Management of Equipment All lamps on Sound on All lamps off Sound off Switching Operation Sound On/OffPress and hold Button for more than two seconds Switch the display to check the rest of the total numberChecking Total Number Copied Zooming in button to change Changing of the Enabled Energy Saving ModePress Button to switch the enabled mode Auto sleep timeWhen Message Lamp is Lit/Blinking Paper Jams TroubleshootingToner lamp When Message Lamp is Lit/BlinkingCover open lamp Paper empty lampRecommended toner cartridges Paper jam lampService call lamp Checking position of paper jams When paper jams occur frequentlyPaper Jams Do not tear jammed paper When releasing jammed paperPaper jams within Automatic Document Feeder optional Lower Open the Automatic Document FeederPaper Jams Raise the lever and open the upper cover Paper jams within Automatic Document Feeder optional UpperPaper Jams Pull out the paper jammed on the bypass tray Paper jams on bypass trayPaper jam behind transfer unit Close the transfer unit and the side cover Paper jams within fuser unitPaper Jams Paper jams within Paper Feed Unit optional Never attempt to incinerate toner cartridges Replacing Toner CartridgeOpen the front cover Hold down the green lever Pull out the toner cartridge Clean the charger Replacing Toner Cartridge With the transfer charger wire Phenomenon Usual cause Countermeasure Before Calling Service TechnicianGeneral operation Original/Copy paper-related items Toner-related itemsImage trouble Before Calling Service Technician Page Daily Inspection Maintenance and InspectionOriginal glass Guides Platen sheet Daily InspectionOpen the front cover Clean the charger Cleaning chargerCleaning transfer charger Daily Inspection Page Continuous copying speed 103 Packing list STUDIO181 Specifications 102Specifications of Options 104 OPC STUDIO181 SpecificationsPaper size Feeder Continuous Copying speed Continuous copying speedPacking list Paper Feed Unit Specifications of OptionsAutomatic Document Feeder Index 102 Page Multifunctional Digital Systems