Toshiba DP-1810 manual Interrupting copying and making another copy Interrupt copy

Page 49

Interrupting copying and making another copy - Interrupt copy -

You can interrupt copying of one job and make another copy job (= interrupt copying). The copy quantity or functions applied to the interrupted job are stored in the memory of this equipment, so that you will not need to set them again when the interrupted job resumes.

Interrupt copying is available only when the originals are placed on the Automatic Document Feeder (optional) and the sort functions are used.

1 Press the [INTERRUPT] button.

The [INTERRUPT] lamp blinks, and the lamp will be fully lit after a while.

When the [INTERRUPT] button is pressed during scanning, the [INTERRUPT] lamp blinks, and then the lamp will be fully lit after the scanning has finished.

2 Replace the original with a new one.

3 Select the copy modes as required, and then press the [START] button.

Interrupt copying starts.

4 After you have finished interrupt copying, press the [INTERRUPT] button.

The copying status returns to the one before the interruption.

Even if you do not press the [INTERRUPT] button, a certain time after the interrupt copy- ing has finished, the auto clear function will work and the interrupt mode will automati- cally be cleared.

5 Press the [START] button. The job interrupted will resume.

Making Copies 47

Image 49

Contents Operators Manual for Copying Functions Page Preface PrefaceFCC Notice Before Reading This Manual How to read this manual Symbols in this manualTrademarks Description of original/paper directionContents Switching Operation Sound On/Off Adjusting Density LevelChanging of the Enabled Energy Saving Mode When Message Lamp is Lit/Blinking105 Daily Inspection Cleaning charger Cleaning transfer chargerContents Recommended toner cartridges Toshiba Quality Is Second to NoneCartridge detecting function Toner remaining check functionToner Supplies / PartsGeneral When installing or moving General Precautions31.5 Other pointsWhen using the equipment Position of Certification label, etc When handling supplies During maintenance or inspectionFirst-aid measures Poration Disclaimer NoticeLow power mode Energy saving featuresSleep mode / Super sleep mode Environmental InformationDescription of Each Component Preparation 1 Turning Power onPreparation 2 Placing Copy Paper Front / Right side Description of Each ComponentPlaten Cover optional, KA-1650PC Automatic Document Feeder optional, MR-2020Left side / Inner side Receiving tray Scanning area USB terminal 4-pinOriginal scale Platen sheetConfiguration of options Control panel Density adjustment buttons/lamps Original mode button/lampsOriginal setting lamp Interrupt button/lampOriginal button/lamps Copy button/lampsAPS/AMS selecting button/lamps Turning power on Preparation 1 Turning Power onTurning power OFF Press the power switch to on sideTypes of energy saving mode Saving energy when not in use Energy saving modeTo turn the equipment into the energy saving mode manually Canceling conditions for energy saving modeSuper sleep mode Acceptable media types Preparation 2 Placing Copy PaperFeeder Media type Paper size Maximum sheet Capacity *1 Paper types not acceptable Recommended paperStoring paper Media type Product namePress down the paper plate Placing paper in drawersWiden the gap with both hands Place paper in the drawer Adjust the side guides to the desired paper sizeRegister the paper size into the equipment Do not let your fingers be caught when closing the drawerRegistering standard size LD, LT, LT-R, LG, ST-R Preparation 3 Registering Size of Paper PlacedCode No Registering other standard sizesPress the Start button Placing Originals Using Bypass TrayMaking Copies Placing Originals Setting position Type of origiAcceptable originals Maximum number of originals scanned in one goPlacing originals on the original glass Placing booklet-type originals such as books or catalogs Precautions for Automatic Document Feeder optional Using Automatic Document Feeder optionalWhen black streaks appear on the copied image Media types Maximum size Maximum number Paper weightPlacing originals on Automatic Document Feeder optional When placing a large amount of originals with a long widthCheck if paper is placed in the drawer Making CopiesPlace the original Select the copy modes as requiredWhen the paper has run out When the number of sheets exiting has exceededStopping/Resuming copying Press the CLEAR/STOP button during scanning or copyingPress the Interrupt button Interrupting copying and making another copy Interrupt copyMedia type Paper size Maximum sheet Capacity *1 Using Bypass TrayBypass copying Paper size has been registered Placed on the bypass tray is litZooming In/Out Copy Image Default Settings Paper SelectionAutomatic paper selection APS Manual paper selection Contents Default setting at installation Default SettingsAutomatic paper selection APS Paper SelectionPlace the original on the Automatic Document Feeder Automatic paper selection APSPlace paper in the drawer Place the original Manual paper selectionSelecting the drawer of the equipment Automatic magnification selection AMS Zooming In/Out Copy ImageAutomatic magnification selection AMS Specifying reproduction ratio manuallyIf the Function Clear lamp is blinking and copying stops Specifying both the sizes of the original and the copy paper Press Zooming out or Specifying reproduction ratio manuallyDesired reproduction ratio appears Zooming in button untilZooming In/Out Copy Image Press the Sort button Copying in Same Page Order as Originals Sort CopyingButton Sort buttonOriginal is scanned Repeat this until all originals have been scannedCopying Both Sides of Card into 1 Page ID Card Page Selecting Image Mode To adjust the density to the desired level Adjusting Density LevelTo return it to the automatic copy density mode DarkSettings and Management of Equipment All lamps on Sound on All lamps off Sound off Switching Operation Sound On/OffChecking Total Number Copied Switch the display to check the rest of the total numberPress and hold Button for more than two seconds Press Button to switch the enabled mode Changing of the Enabled Energy Saving ModeAuto sleep time Zooming in button to changeWhen Message Lamp is Lit/Blinking Paper Jams TroubleshootingCover open lamp When Message Lamp is Lit/BlinkingPaper empty lamp Toner lampRecommended toner cartridges Paper jam lampService call lamp Paper Jams When paper jams occur frequentlyChecking position of paper jams Paper jams within Automatic Document Feeder optional Lower When releasing jammed paperOpen the Automatic Document Feeder Do not tear jammed paperPaper Jams Raise the lever and open the upper cover Paper jams within Automatic Document Feeder optional UpperPaper Jams Pull out the paper jammed on the bypass tray Paper jams on bypass trayPaper jam behind transfer unit Close the transfer unit and the side cover Paper jams within fuser unitPaper Jams Paper jams within Paper Feed Unit optional Open the front cover Hold down the green lever Replacing Toner CartridgeNever attempt to incinerate toner cartridges Pull out the toner cartridge Clean the charger Replacing Toner Cartridge With the transfer charger wire General operation Before Calling Service TechnicianPhenomenon Usual cause Countermeasure Original/Copy paper-related items Toner-related itemsImage trouble Before Calling Service Technician Page Daily Inspection Maintenance and InspectionOriginal glass Guides Platen sheet Daily InspectionOpen the front cover Clean the charger Cleaning chargerCleaning transfer charger Daily Inspection Page Specifications of Options 104 STUDIO181 Specifications 102Continuous copying speed 103 Packing list OPC STUDIO181 SpecificationsPacking list Continuous copying speedPaper size Feeder Continuous Copying speed Automatic Document Feeder Specifications of OptionsPaper Feed Unit Index 102 Page Multifunctional Digital Systems