Toshiba DP-1810 manual Clean the charger

Page 89

6

7

Pull out the seal in the direction of the arrow.

Insert the toner cartridge along the rail.

yBefore inserting the toner cartridge, check if the green lever is raised and raise it if not.

yInsert the toner cartridge until you hear a click sound.

8 Clean the charger.

Hold the cleaning knob of the charger and pull it out toward you carefully until it comes to a stop. Then reinsert it in its original position carefully. Repeat this procedure two or three times.

Check if the cleaning knob is fully inserted after cleaning.

After the toner cartridge has been replaced, be sure to clean the transfer charger wire following the procedure below in order to prevent uneven density of images.

Replacing Toner Cartridge 87

Page 88 Page 90
Image 89
Page 88 Page 90
Contents Operators Manual for Copying Functions Page Preface PrefaceFCC Notice Before Reading This Manual How to read this manual Symbols in this manualTrademarks Description of original/paper directionContents Switching Operation Sound On/Off Adjusting Density LevelChanging of the Enabled Energy Saving Mode When Message Lamp is Lit/Blinking105 Daily Inspection Cleaning charger Cleaning transfer chargerContents Recommended toner cartridges Toshiba Quality Is Second to NoneCartridge detecting function Toner remaining check functionGeneral Supplies / PartsToner When installing or moving General Precautions31.5 Other pointsWhen using the equipment Position of Certification label, etc When handling supplies During maintenance or inspectionFirst-aid measures Poration Disclaimer NoticeLow power mode Energy saving featuresSleep mode / Super sleep mode Environmental InformationPreparation 2 Placing Copy Paper Preparation 1 Turning Power onDescription of Each Component Front / Right side Description of Each ComponentPlaten Cover optional, KA-1650PC Automatic Document Feeder optional, MR-2020Left side / Inner side Receiving tray Scanning area USB terminal 4-pinOriginal scale Platen sheetConfiguration of options Control panel Density adjustment buttons/lamps Original mode button/lampsOriginal setting lamp Interrupt button/lampAPS/AMS selecting button/lamps Copy button/lampsOriginal button/lamps Turning power on Preparation 1 Turning Power onTurning power OFF Press the power switch to on sideTypes of energy saving mode Saving energy when not in use Energy saving modeTo turn the equipment into the energy saving mode manually Canceling conditions for energy saving modeSuper sleep mode Feeder Media type Paper size Maximum sheet Capacity *1 Preparation 2 Placing Copy PaperAcceptable media types Paper types not acceptable Recommended paperStoring paper Media type Product namePress down the paper plate Placing paper in drawersWiden the gap with both hands Place paper in the drawer Adjust the side guides to the desired paper sizeRegister the paper size into the equipment Do not let your fingers be caught when closing the drawerRegistering standard size LD, LT, LT-R, LG, ST-R Preparation 3 Registering Size of Paper PlacedCode No Registering other standard sizesPress the Start button Making Copies Using Bypass TrayPlacing Originals Placing Originals Setting position Type of origiAcceptable originals Maximum number of originals scanned in one goPlacing originals on the original glass Placing booklet-type originals such as books or catalogs Precautions for Automatic Document Feeder optional Using Automatic Document Feeder optionalWhen black streaks appear on the copied image Media types Maximum size Maximum number Paper weightPlacing originals on Automatic Document Feeder optional When placing a large amount of originals with a long widthCheck if paper is placed in the drawer Making CopiesPlace the original Select the copy modes as requiredWhen the paper has run out When the number of sheets exiting has exceededStopping/Resuming copying Press the CLEAR/STOP button during scanning or copyingPress the Interrupt button Interrupting copying and making another copy Interrupt copyMedia type Paper size Maximum sheet Capacity *1 Using Bypass TrayBypass copying Paper size has been registered Placed on the bypass tray is litAutomatic paper selection APS Manual paper selection Default Settings Paper SelectionZooming In/Out Copy Image Contents Default setting at installation Default SettingsAutomatic paper selection APS Paper SelectionPlace the original on the Automatic Document Feeder Automatic paper selection APSPlace paper in the drawer Place the original Manual paper selectionSelecting the drawer of the equipment Automatic magnification selection AMS Zooming In/Out Copy ImageAutomatic magnification selection AMS Specifying reproduction ratio manuallyIf the Function Clear lamp is blinking and copying stops Specifying both the sizes of the original and the copy paper Press Zooming out or Specifying reproduction ratio manuallyDesired reproduction ratio appears Zooming in button untilZooming In/Out Copy Image Press the Sort button Copying in Same Page Order as Originals Sort CopyingButton Sort buttonOriginal is scanned Repeat this until all originals have been scannedCopying Both Sides of Card into 1 Page ID Card Page Selecting Image Mode To adjust the density to the desired level Adjusting Density LevelTo return it to the automatic copy density mode DarkSettings and Management of Equipment All lamps on Sound on All lamps off Sound off Switching Operation Sound On/OffPress and hold Button for more than two seconds Switch the display to check the rest of the total numberChecking Total Number Copied Press Button to switch the enabled mode Changing of the Enabled Energy Saving ModeAuto sleep time Zooming in button to changeWhen Message Lamp is Lit/Blinking Paper Jams TroubleshootingCover open lamp When Message Lamp is Lit/BlinkingPaper empty lamp Toner lampRecommended toner cartridges Paper jam lampService call lamp Checking position of paper jams When paper jams occur frequentlyPaper Jams Paper jams within Automatic Document Feeder optional Lower When releasing jammed paperOpen the Automatic Document Feeder Do not tear jammed paperPaper Jams Raise the lever and open the upper cover Paper jams within Automatic Document Feeder optional UpperPaper Jams Pull out the paper jammed on the bypass tray Paper jams on bypass trayPaper jam behind transfer unit Close the transfer unit and the side cover Paper jams within fuser unitPaper Jams Paper jams within Paper Feed Unit optional Never attempt to incinerate toner cartridges Replacing Toner CartridgeOpen the front cover Hold down the green lever Pull out the toner cartridge Clean the charger Replacing Toner Cartridge With the transfer charger wire Phenomenon Usual cause Countermeasure Before Calling Service TechnicianGeneral operation Original/Copy paper-related items Toner-related itemsImage trouble Before Calling Service Technician Page Daily Inspection Maintenance and InspectionOriginal glass Guides Platen sheet Daily InspectionOpen the front cover Clean the charger Cleaning chargerCleaning transfer charger Daily Inspection Page Continuous copying speed 103 Packing list STUDIO181 Specifications 102Specifications of Options 104 OPC STUDIO181 SpecificationsPaper size Feeder Continuous Copying speed Continuous copying speedPacking list Paper Feed Unit Specifications of OptionsAutomatic Document Feeder Index 102 Page Multifunctional Digital Systems
Top Page Image Contents