Toshiba DP-1810 manual Preparation 2 Placing Copy Paper, Acceptable media types

Page 32

1 PREPARATION

Preparation 2 - Placing Copy Paper

Place copy paper in an appropriate paper source before you start copying.

Acceptable media types

Standard size plain paper (17 to 20 lb. Bond) can be used for the drawers in the equipment and the Paper Feed Unit (optional). See the table below for the details.

	Feeder	Media type	Paper size	Maximum sheet
	Feeder	Media type	Paper size	capacity *1
				capacity *1
	Drawers of	Plain paper	LT format:	250 sheets
	the equip-	(17 - 20 lb. Bond)	LD, LG, LT, LT-R, COMP, 13"LG	(17 lb. Bond)
	ment and		A/B format:	250 sheets
	Paper Feed		A3, A4, A4-R, B4, B5, B5-R, FOLIO	(20 lb. Bond)
	Unit
	(optional)
	Bypass tray	Plain paper	LT format:	100 sheets
		(17 - 20 lb. Bond)*2	LD, LG, LT, LT-R, ST-R, COMP, 13"LG	(17 lb. Bond)
			A/B format:	100 sheets
			A3, A4, A4-R, A5-R, B4, B5, B5-R, FOLIO	(20 lb. Bond)
		THICK PAPER 1		1 sheet
		(21 - 28 lb. Bond)		(21 - 28 lb. Bond)
		THICK PAPER 2		1 sheet
		(29 lb. Bond - 90 lb.		(29 lb. Bond - 90
		Index)		lb. Index)
		Tracing paper		1 sheet
		(20 lb.)
		Sticker labels		1 sheet
		Transparencies*3	LT only	1 sheet

*1 “Maximum sheet capacity” refers to the maximum number of sheets when TOSHIBA-recommended paper is used. See the following page for the TOSHIBA-recommended paper:

P.31 “Recommended paper”

*2 13 to 16 lb. Bond paper can be used if it is set on the bypass tray sheet by sheet.

*3 Be sure to use the overhead transparencies that TOSHIBA recommends. When transparencies other than the TOSHIBA-recommended ones are used, this could cause an equipment malfunction.

You cannot mix various paper sizes in one drawer.

Abbreviations for LT format sizes:

LT: Letter, LD: Ledger, LG: Legal, ST: Statement, COMP: Computer

30 Preparation 2 - Placing Copy Paper

Image 32

Contents Operators Manual for Copying Functions Page Preface PrefaceFCC Notice How to read this manual Symbols in this manual Before Reading This ManualDescription of original/paper direction TrademarksContents Adjusting Density Level Switching Operation Sound On/OffChanging of the Enabled Energy Saving Mode When Message Lamp is Lit/BlinkingDaily Inspection Cleaning charger Cleaning transfer charger 105Contents Toshiba Quality Is Second to None Recommended toner cartridgesCartridge detecting function Toner remaining check functionGeneral Supplies / PartsToner General Precautions When installing or movingOther points 31.5When using the equipment Position of Certification label, etc During maintenance or inspection When handling suppliesFirst-aid measures Disclaimer Notice PorationEnergy saving features Low power modeSleep mode / Super sleep mode Environmental InformationPreparation 2 Placing Copy Paper Preparation 1 Turning Power onDescription of Each Component Description of Each Component Front / Right sidePlaten Cover optional, KA-1650PC Automatic Document Feeder optional, MR-2020Left side / Inner side USB terminal 4-pin Receiving tray Scanning areaOriginal scale Platen sheetConfiguration of options Control panel Original mode button/lamps Density adjustment buttons/lampsOriginal setting lamp Interrupt button/lampAPS/AMS selecting button/lamps Copy button/lampsOriginal button/lamps Preparation 1 Turning Power on Turning power onTurning power OFF Press the power switch to on sideSaving energy when not in use Energy saving mode Types of energy saving modeTo turn the equipment into the energy saving mode manually Canceling conditions for energy saving modeSuper sleep mode Feeder Media type Paper size Maximum sheet Capacity *1 Preparation 2 Placing Copy PaperAcceptable media types Recommended paper Paper types not acceptableStoring paper Media type Product namePlacing paper in drawers Press down the paper plateWiden the gap with both hands Adjust the side guides to the desired paper size Place paper in the drawerDo not let your fingers be caught when closing the drawer Register the paper size into the equipmentPreparation 3 Registering Size of Paper Placed Registering standard size LD, LT, LT-R, LG, ST-RRegistering other standard sizes Code NoPress the Start button Making Copies Using Bypass TrayPlacing Originals Setting position Type of origi Placing OriginalsAcceptable originals Maximum number of originals scanned in one goPlacing originals on the original glass Placing booklet-type originals such as books or catalogs Using Automatic Document Feeder optional Precautions for Automatic Document Feeder optionalWhen black streaks appear on the copied image Media types Maximum size Maximum number Paper weightWhen placing a large amount of originals with a long width Placing originals on Automatic Document Feeder optionalMaking Copies Check if paper is placed in the drawerPlace the original Select the copy modes as requiredWhen the number of sheets exiting has exceeded When the paper has run outStopping/Resuming copying Press the CLEAR/STOP button during scanning or copyingInterrupting copying and making another copy Interrupt copy Press the Interrupt buttonUsing Bypass Tray Media type Paper size Maximum sheet Capacity *1Bypass copying Placed on the bypass tray is lit Paper size has been registeredAutomatic paper selection APS Manual paper selection Default Settings Paper SelectionZooming In/Out Copy Image Default Settings Contents Default setting at installationPaper Selection Automatic paper selection APSPlace the original on the Automatic Document Feeder Automatic paper selection APSManual paper selection Place paper in the drawer Place the originalSelecting the drawer of the equipment Zooming In/Out Copy Image Automatic magnification selection AMSAutomatic magnification selection AMS Specifying reproduction ratio manuallyIf the Function Clear lamp is blinking and copying stops Specifying both the sizes of the original and the copy paper Specifying reproduction ratio manually Press Zooming out orDesired reproduction ratio appears Zooming in button untilZooming In/Out Copy Image Copying in Same Page Order as Originals Sort Copying Press the Sort buttonSort button ButtonOriginal is scanned Repeat this until all originals have been scannedCopying Both Sides of Card into 1 Page ID Card Page Selecting Image Mode Adjusting Density Level To adjust the density to the desired levelTo return it to the automatic copy density mode DarkSettings and Management of Equipment Switching Operation Sound On/Off All lamps on Sound on All lamps off Sound offPress and hold Button for more than two seconds Switch the display to check the rest of the total numberChecking Total Number Copied Changing of the Enabled Energy Saving Mode Press Button to switch the enabled modeAuto sleep time Zooming in button to changeTroubleshooting When Message Lamp is Lit/Blinking Paper JamsWhen Message Lamp is Lit/Blinking Cover open lampPaper empty lamp Toner lampPaper jam lamp Recommended toner cartridgesService call lamp Checking position of paper jams When paper jams occur frequentlyPaper Jams When releasing jammed paper Paper jams within Automatic Document Feeder optional LowerOpen the Automatic Document Feeder Do not tear jammed paperPaper Jams Paper jams within Automatic Document Feeder optional Upper Raise the lever and open the upper coverPaper Jams Paper jams on bypass tray Pull out the paper jammed on the bypass trayPaper jam behind transfer unit Paper jams within fuser unit Close the transfer unit and the side coverPaper Jams Paper jams within Paper Feed Unit optional Never attempt to incinerate toner cartridges Replacing Toner CartridgeOpen the front cover Hold down the green lever Pull out the toner cartridge Clean the charger Replacing Toner Cartridge With the transfer charger wire Phenomenon Usual cause Countermeasure Before Calling Service TechnicianGeneral operation Toner-related items Original/Copy paper-related itemsImage trouble Before Calling Service Technician Page Maintenance and Inspection Daily InspectionDaily Inspection Original glass Guides Platen sheetCleaning charger Open the front cover Clean the chargerCleaning transfer charger Daily Inspection Page Continuous copying speed 103 Packing list STUDIO181 Specifications 102Specifications of Options 104 STUDIO181 Specifications OPCPaper size Feeder Continuous Copying speed Continuous copying speedPacking list Paper Feed Unit Specifications of OptionsAutomatic Document Feeder Index 102 Page Multifunctional Digital Systems