Toshiba DP-1810 manual Placed on the bypass tray is lit, Paper size has been registered

Page 52

2 HOW TO MAKE COPIES

3

Press the [START] button.

The paper size has been registered.

4

Press the media type setting button until the lamp of the media type

placed on the bypass tray is lit.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

You can select the media type from the following three:

THICK PAPER 1: Thick paper (21 to 28 lb. Bond)

THICK PAPER 2: Thick paper (29 lb. Bond to 90 lb. Index), sticker labels

TRANSPARENCY: Overhead transparencies

yYou do not need to select the media type when you use plain paper (17 to 20 lb. Bond) or tracing paper.

yIf you select a different media type from the one you placed on the bypass tray, this could cause a paper jam or the quality of the copied image could be lowered.

5 Place the original.

6 Select the other copy modes as required, and then press the [START] button.

Copying starts.

When you make copies on overhead transparencies using the bypass tray, pick up the transparencies which have exited onto the receiving tray one by one. If the transparen- cies pile up, they may become curled and not be good for projection.

yWhen the paper on the bypass tray has run out during copying, copying continues with the paper of the same size in the drawer as the one on the bypass tray. (If the size of the paper on the bypass tray has not been registered in advance, however, copying stops. In this case, add paper to the bypass tray and press the [START] but- ton to resume copying.)

yWhen bypass copying has finished, the [FUNCTION CLEAR] lamp blinks. Press the [FUNCTION CLEAR] button so that the paper size setting for the bypass tray will be cleared. Press the [FUNCTION CLEAR] button again so that bypass copying will be switched to copying with drawer feeding.

50 Using Bypass Tray

Image 52
Contents Operators Manual for Copying Functions Page Preface PrefaceFCC Notice How to read this manual Symbols in this manual Before Reading This ManualDescription of original/paper direction TrademarksContents Adjusting Density Level Switching Operation Sound On/OffChanging of the Enabled Energy Saving Mode When Message Lamp is Lit/BlinkingDaily Inspection Cleaning charger Cleaning transfer charger 105Contents Toshiba Quality Is Second to None Recommended toner cartridgesCartridge detecting function Toner remaining check functionToner Supplies / PartsGeneral General Precautions When installing or movingOther points 31.5When using the equipment Position of Certification label, etc During maintenance or inspection When handling suppliesFirst-aid measures Disclaimer Notice PorationEnergy saving features Low power modeSleep mode / Super sleep mode Environmental InformationDescription of Each Component Preparation 1 Turning Power onPreparation 2 Placing Copy Paper Description of Each Component Front / Right sidePlaten Cover optional, KA-1650PC Automatic Document Feeder optional, MR-2020Left side / Inner side USB terminal 4-pin Receiving tray Scanning areaOriginal scale Platen sheetConfiguration of options Control panel Original mode button/lamps Density adjustment buttons/lampsOriginal setting lamp Interrupt button/lampOriginal button/lamps Copy button/lampsAPS/AMS selecting button/lamps Preparation 1 Turning Power on Turning power onTurning power OFF Press the power switch to on sideSaving energy when not in use Energy saving mode Types of energy saving modeTo turn the equipment into the energy saving mode manually Canceling conditions for energy saving modeSuper sleep mode Acceptable media types Preparation 2 Placing Copy PaperFeeder Media type Paper size Maximum sheet Capacity *1 Recommended paper Paper types not acceptableStoring paper Media type Product namePlacing paper in drawers Press down the paper plateWiden the gap with both hands Adjust the side guides to the desired paper size Place paper in the drawerDo not let your fingers be caught when closing the drawer Register the paper size into the equipmentPreparation 3 Registering Size of Paper Placed Registering standard size LD, LT, LT-R, LG, ST-RRegistering other standard sizes Code NoPress the Start button Placing Originals Using Bypass TrayMaking Copies Setting position Type of origi Placing OriginalsAcceptable originals Maximum number of originals scanned in one goPlacing originals on the original glass Placing booklet-type originals such as books or catalogs Using Automatic Document Feeder optional Precautions for Automatic Document Feeder optionalWhen black streaks appear on the copied image Media types Maximum size Maximum number Paper weightWhen placing a large amount of originals with a long width Placing originals on Automatic Document Feeder optionalMaking Copies Check if paper is placed in the drawerPlace the original Select the copy modes as requiredWhen the number of sheets exiting has exceeded When the paper has run outStopping/Resuming copying Press the CLEAR/STOP button during scanning or copyingInterrupting copying and making another copy Interrupt copy Press the Interrupt buttonUsing Bypass Tray Media type Paper size Maximum sheet Capacity *1Bypass copying Placed on the bypass tray is lit Paper size has been registeredZooming In/Out Copy Image Default Settings Paper SelectionAutomatic paper selection APS Manual paper selection Default Settings Contents Default setting at installationPaper Selection Automatic paper selection APSPlace the original on the Automatic Document Feeder Automatic paper selection APSManual paper selection Place paper in the drawer Place the originalSelecting the drawer of the equipment Zooming In/Out Copy Image Automatic magnification selection AMSAutomatic magnification selection AMS Specifying reproduction ratio manuallyIf the Function Clear lamp is blinking and copying stops Specifying both the sizes of the original and the copy paper Specifying reproduction ratio manually Press Zooming out orDesired reproduction ratio appears Zooming in button untilZooming In/Out Copy Image Copying in Same Page Order as Originals Sort Copying Press the Sort buttonSort button ButtonOriginal is scanned Repeat this until all originals have been scannedCopying Both Sides of Card into 1 Page ID Card Page Selecting Image Mode Adjusting Density Level To adjust the density to the desired levelTo return it to the automatic copy density mode DarkSettings and Management of Equipment Switching Operation Sound On/Off All lamps on Sound on All lamps off Sound offChecking Total Number Copied Switch the display to check the rest of the total numberPress and hold Button for more than two seconds Changing of the Enabled Energy Saving Mode Press Button to switch the enabled modeAuto sleep time Zooming in button to changeTroubleshooting When Message Lamp is Lit/Blinking Paper JamsWhen Message Lamp is Lit/Blinking Cover open lampPaper empty lamp Toner lampPaper jam lamp Recommended toner cartridgesService call lamp Paper Jams When paper jams occur frequentlyChecking position of paper jams When releasing jammed paper Paper jams within Automatic Document Feeder optional LowerOpen the Automatic Document Feeder Do not tear jammed paperPaper Jams Paper jams within Automatic Document Feeder optional Upper Raise the lever and open the upper coverPaper Jams Paper jams on bypass tray Pull out the paper jammed on the bypass trayPaper jam behind transfer unit Paper jams within fuser unit Close the transfer unit and the side coverPaper Jams Paper jams within Paper Feed Unit optional Open the front cover Hold down the green lever Replacing Toner CartridgeNever attempt to incinerate toner cartridges Pull out the toner cartridge Clean the charger Replacing Toner Cartridge With the transfer charger wire General operation Before Calling Service TechnicianPhenomenon Usual cause Countermeasure Toner-related items Original/Copy paper-related itemsImage trouble Before Calling Service Technician Page Maintenance and Inspection Daily InspectionDaily Inspection Original glass Guides Platen sheetCleaning charger Open the front cover Clean the chargerCleaning transfer charger Daily Inspection Page Specifications of Options 104 STUDIO181 Specifications 102Continuous copying speed 103 Packing list STUDIO181 Specifications OPCPacking list Continuous copying speedPaper size Feeder Continuous Copying speed Automatic Document Feeder Specifications of OptionsPaper Feed Unit Index 102 Page Multifunctional Digital Systems