Toshiba DP-1810 manual Zooming In/Out Copy Image, Automatic magnification selection AMS

Page 58

3 COPYING FUNCTIONS

Zooming In/Out Copy Image

You can set the reproduction ratio of the copy image in the following three ways:

Automatic magnification selection (AMS):

Specify the size of the copy paper in advance. As the original is placed, the equipment then detects the size of the original and sets the reproduction ratio most suited to the size of copy paper automatically. This function is enabled only when standard size originals (LD, LG, LT, LT-R, COMP, ST-R) are used and also the Automatic Document Feeder (optional) is used.

Specifying both the sizes of the original and the copy paper:

When you specify the sizes of both the original and the copy paper, the equipment automatically sets the reproduction ratio most suited to both of these sizes. This function can be used in case AMS cannot be, such as when the originals are overhead transparencies, or when an original is placed on the original glass.

Specifying reproduction ratio manually:

Specify the reproduction ratio manually with the Zoom buttons (zooming out: , zooming

in: ) from 25% to 200%.

Automatic magnification selection (AMS)

Specify the copy paper size to be used in advance. The equipment then detects the size of the original and automatically sets the most suitable reproduction ratio for the size of copy paper, as the original is placed.

yAutomatic magnification selection (AMS) can be used only when you place originals on the Automatic Document Feeder (optional).

yThe standard sizes the equipment can detect are as follows: LD, LG, LT, LT-R, COMP, ST-R

Automatic magnification selection (AMS) may not work correctly for the size of originals listed below. Use other methods to set the reproduction ratio for the following originals:

yHighly transparent ones (e.g. overhead transparencies, tracing paper)

yWholly dark ones or ones with dark borders

yNon-standard size (e.g. newspapers, magazines)

56 Zooming In/Out Copy Image

Image 58

Contents Operators Manual for Copying Functions Page Preface PrefaceFCC Notice How to read this manual Symbols in this manual Before Reading This ManualDescription of original/paper direction TrademarksContents Changing of the Enabled Energy Saving Mode Adjusting Density LevelSwitching Operation Sound On/Off When Message Lamp is Lit/BlinkingDaily Inspection Cleaning charger Cleaning transfer charger 105Contents Cartridge detecting function Toshiba Quality Is Second to NoneRecommended toner cartridges Toner remaining check functionToner Supplies / PartsGeneral General Precautions When installing or movingOther points 31.5When using the equipment Position of Certification label, etc During maintenance or inspection When handling suppliesFirst-aid measures Disclaimer Notice PorationSleep mode / Super sleep mode Energy saving featuresLow power mode Environmental InformationDescription of Each Component Preparation 1 Turning Power onPreparation 2 Placing Copy Paper Platen Cover optional, KA-1650PC Description of Each ComponentFront / Right side Automatic Document Feeder optional, MR-2020Left side / Inner side Original scale USB terminal 4-pinReceiving tray Scanning area Platen sheetConfiguration of options Control panel Original setting lamp Original mode button/lampsDensity adjustment buttons/lamps Interrupt button/lampOriginal button/lamps Copy button/lampsAPS/AMS selecting button/lamps Turning power OFF Preparation 1 Turning Power onTurning power on Press the power switch to on sideTo turn the equipment into the energy saving mode manually Saving energy when not in use Energy saving modeTypes of energy saving mode Canceling conditions for energy saving modeSuper sleep mode Acceptable media types Preparation 2 Placing Copy PaperFeeder Media type Paper size Maximum sheet Capacity *1 Storing paper Recommended paperPaper types not acceptable Media type Product namePlacing paper in drawers Press down the paper plateWiden the gap with both hands Adjust the side guides to the desired paper size Place paper in the drawerDo not let your fingers be caught when closing the drawer Register the paper size into the equipmentPreparation 3 Registering Size of Paper Placed Registering standard size LD, LT, LT-R, LG, ST-RRegistering other standard sizes Code NoPress the Start button Placing Originals Using Bypass TrayMaking Copies Acceptable originals Setting position Type of origiPlacing Originals Maximum number of originals scanned in one goPlacing originals on the original glass Placing booklet-type originals such as books or catalogs When black streaks appear on the copied image Using Automatic Document Feeder optionalPrecautions for Automatic Document Feeder optional Media types Maximum size Maximum number Paper weightWhen placing a large amount of originals with a long width Placing originals on Automatic Document Feeder optionalPlace the original Making CopiesCheck if paper is placed in the drawer Select the copy modes as requiredStopping/Resuming copying When the number of sheets exiting has exceededWhen the paper has run out Press the CLEAR/STOP button during scanning or copyingInterrupting copying and making another copy Interrupt copy Press the Interrupt buttonUsing Bypass Tray Media type Paper size Maximum sheet Capacity *1Bypass copying Placed on the bypass tray is lit Paper size has been registeredZooming In/Out Copy Image Default Settings Paper SelectionAutomatic paper selection APS Manual paper selection Default Settings Contents Default setting at installation Place the original on the Automatic Document Feeder Paper Selection Automatic paper selection APS Automatic paper selection APSManual paper selection Place paper in the drawer Place the originalSelecting the drawer of the equipment Automatic magnification selection AMS Zooming In/Out Copy ImageAutomatic magnification selection AMS Specifying reproduction ratio manuallyIf the Function Clear lamp is blinking and copying stops Specifying both the sizes of the original and the copy paper Desired reproduction ratio appears Specifying reproduction ratio manuallyPress Zooming out or Zooming in button untilZooming In/Out Copy Image Copying in Same Page Order as Originals Sort Copying Press the Sort buttonOriginal is scanned Sort buttonButton Repeat this until all originals have been scannedCopying Both Sides of Card into 1 Page ID Card Page Selecting Image Mode To return it to the automatic copy density mode Adjusting Density LevelTo adjust the density to the desired level DarkSettings and Management of Equipment Switching Operation Sound On/Off All lamps on Sound on All lamps off Sound offChecking Total Number Copied Switch the display to check the rest of the total numberPress and hold Button for more than two seconds Auto sleep time Changing of the Enabled Energy Saving ModePress Button to switch the enabled mode Zooming in button to changeTroubleshooting When Message Lamp is Lit/Blinking Paper JamsPaper empty lamp When Message Lamp is Lit/BlinkingCover open lamp Toner lampPaper jam lamp Recommended toner cartridgesService call lamp Paper Jams When paper jams occur frequentlyChecking position of paper jams Open the Automatic Document Feeder When releasing jammed paperPaper jams within Automatic Document Feeder optional Lower Do not tear jammed paperPaper Jams Paper jams within Automatic Document Feeder optional Upper Raise the lever and open the upper coverPaper Jams Paper jams on bypass tray Pull out the paper jammed on the bypass trayPaper jam behind transfer unit Paper jams within fuser unit Close the transfer unit and the side coverPaper Jams Paper jams within Paper Feed Unit optional Open the front cover Hold down the green lever Replacing Toner CartridgeNever attempt to incinerate toner cartridges Pull out the toner cartridge Clean the charger Replacing Toner Cartridge With the transfer charger wire General operation Before Calling Service TechnicianPhenomenon Usual cause Countermeasure Toner-related items Original/Copy paper-related itemsImage trouble Before Calling Service Technician Page Maintenance and Inspection Daily InspectionDaily Inspection Original glass Guides Platen sheetCleaning charger Open the front cover Clean the chargerCleaning transfer charger Daily Inspection Page Specifications of Options 104 STUDIO181 Specifications 102Continuous copying speed 103 Packing list STUDIO181 Specifications OPCPacking list Continuous copying speedPaper size Feeder Continuous Copying speed Automatic Document Feeder Specifications of OptionsPaper Feed Unit Index 102 Page Multifunctional Digital Systems