Toshiba DP-1810 manual

Page 66
64 Copying Both Sides of Card into 1 Page - ID CARD -
Lower the Platen Cover (optional) or the Automatic Document Feeder (optional) carefully.
Press the [START] button.
The back side of the original is scanned and copying starts.
9
10
Raise the Platen Cover (optional) or the Automatic Document Feeder (optional).
Turn over the card and place it on the original glass again. Align and push it to the left rear corner of the original glass.
The portion of an original which is on the upper and left edges (width of approx. 0.08") of the original glass may not be copied. Place an original away from both edges, if you want to copy the whole of the original.
7
8
The portion of an original which is on the upper and left edges (width of approx. 0.08") of the original glass may not be copied. Place an original away from both edges, if you want to copy the whole of the original.
5 Lower the Platen Cover (optional) or the Automatic Document Feeder (optional) carefully.
6 Select the other copy modes (copy quantity, density, image mode and media type) as required, and then press the [START] button. The scanning of its top side starts and “set” appears on the LED display.
Place a card original on the original glass.
Place the card face down, aligning and pushing it to the left rear corner of the original glass.
4
3 COPYING FUNCTIONS
Page 65 Page 67
Image 66
Page 65 Page 67
Contents Operators Manual for Copying Functions Page Preface PrefaceFCC Notice How to read this manual Symbols in this manual Before Reading This ManualDescription of original/paper direction TrademarksContents Changing of the Enabled Energy Saving Mode Adjusting Density LevelSwitching Operation Sound On/Off When Message Lamp is Lit/BlinkingDaily Inspection Cleaning charger Cleaning transfer charger 105Contents Cartridge detecting function Toshiba Quality Is Second to NoneRecommended toner cartridges Toner remaining check functionSupplies / Parts TonerGeneral General Precautions When installing or movingOther points 31.5When using the equipment Position of Certification label, etc During maintenance or inspection When handling suppliesFirst-aid measures Disclaimer Notice PorationSleep mode / Super sleep mode Energy saving featuresLow power mode Environmental InformationPreparation 1 Turning Power on Description of Each ComponentPreparation 2 Placing Copy Paper Platen Cover optional, KA-1650PC Description of Each ComponentFront / Right side Automatic Document Feeder optional, MR-2020Left side / Inner side Original scale USB terminal 4-pinReceiving tray Scanning area Platen sheetConfiguration of options Control panel Original setting lamp Original mode button/lampsDensity adjustment buttons/lamps Interrupt button/lampCopy button/lamps Original button/lampsAPS/AMS selecting button/lamps Turning power OFF Preparation 1 Turning Power onTurning power on Press the power switch to on sideTo turn the equipment into the energy saving mode manually Saving energy when not in use Energy saving modeTypes of energy saving mode Canceling conditions for energy saving modeSuper sleep mode Preparation 2 Placing Copy Paper Acceptable media typesFeeder Media type Paper size Maximum sheet Capacity *1 Storing paper Recommended paperPaper types not acceptable Media type Product namePlacing paper in drawers Press down the paper plateWiden the gap with both hands Adjust the side guides to the desired paper size Place paper in the drawerDo not let your fingers be caught when closing the drawer Register the paper size into the equipmentPreparation 3 Registering Size of Paper Placed Registering standard size LD, LT, LT-R, LG, ST-RRegistering other standard sizes Code NoPress the Start button Using Bypass Tray Placing OriginalsMaking Copies Acceptable originals Setting position Type of origiPlacing Originals Maximum number of originals scanned in one goPlacing originals on the original glass Placing booklet-type originals such as books or catalogs When black streaks appear on the copied image Using Automatic Document Feeder optionalPrecautions for Automatic Document Feeder optional Media types Maximum size Maximum number Paper weightWhen placing a large amount of originals with a long width Placing originals on Automatic Document Feeder optionalPlace the original Making CopiesCheck if paper is placed in the drawer Select the copy modes as requiredStopping/Resuming copying When the number of sheets exiting has exceededWhen the paper has run out Press the CLEAR/STOP button during scanning or copyingInterrupting copying and making another copy Interrupt copy Press the Interrupt buttonUsing Bypass Tray Media type Paper size Maximum sheet Capacity *1Bypass copying Placed on the bypass tray is lit Paper size has been registeredDefault Settings Paper Selection Zooming In/Out Copy ImageAutomatic paper selection APS Manual paper selection Default Settings Contents Default setting at installationPlace the original on the Automatic Document Feeder Paper SelectionAutomatic paper selection APS Automatic paper selection APSManual paper selection Place paper in the drawer Place the originalSelecting the drawer of the equipment Automatic magnification selection AMS Zooming In/Out Copy ImageAutomatic magnification selection AMS Specifying reproduction ratio manuallyIf the Function Clear lamp is blinking and copying stops Specifying both the sizes of the original and the copy paper Desired reproduction ratio appears Specifying reproduction ratio manuallyPress Zooming out or Zooming in button untilZooming In/Out Copy Image Copying in Same Page Order as Originals Sort Copying Press the Sort buttonOriginal is scanned Sort buttonButton Repeat this until all originals have been scannedCopying Both Sides of Card into 1 Page ID Card Page Selecting Image Mode To return it to the automatic copy density mode Adjusting Density LevelTo adjust the density to the desired level DarkSettings and Management of Equipment Switching Operation Sound On/Off All lamps on Sound on All lamps off Sound offSwitch the display to check the rest of the total number Checking Total Number CopiedPress and hold Button for more than two seconds Auto sleep time Changing of the Enabled Energy Saving ModePress Button to switch the enabled mode Zooming in button to changeTroubleshooting When Message Lamp is Lit/Blinking Paper JamsPaper empty lamp When Message Lamp is Lit/BlinkingCover open lamp Toner lampPaper jam lamp Recommended toner cartridgesService call lamp When paper jams occur frequently Paper JamsChecking position of paper jams Open the Automatic Document Feeder When releasing jammed paperPaper jams within Automatic Document Feeder optional Lower Do not tear jammed paperPaper Jams Paper jams within Automatic Document Feeder optional Upper Raise the lever and open the upper coverPaper Jams Paper jams on bypass tray Pull out the paper jammed on the bypass trayPaper jam behind transfer unit Paper jams within fuser unit Close the transfer unit and the side coverPaper Jams Paper jams within Paper Feed Unit optional Replacing Toner Cartridge Open the front cover Hold down the green leverNever attempt to incinerate toner cartridges Pull out the toner cartridge Clean the charger Replacing Toner Cartridge With the transfer charger wire Before Calling Service Technician General operationPhenomenon Usual cause Countermeasure Toner-related items Original/Copy paper-related itemsImage trouble Before Calling Service Technician Page Maintenance and Inspection Daily InspectionDaily Inspection Original glass Guides Platen sheetCleaning charger Open the front cover Clean the chargerCleaning transfer charger Daily Inspection Page STUDIO181 Specifications 102 Specifications of Options 104Continuous copying speed 103 Packing list STUDIO181 Specifications OPCContinuous copying speed Packing listPaper size Feeder Continuous Copying speed Specifications of Options Automatic Document FeederPaper Feed Unit Index 102 Page Multifunctional Digital Systems
Top Page Image Contents