Toshiba DP-1810 manual Image trouble

Page 94

5 TROUBLESHOOTING

Phenomenon

Usual cause

Countermeasure

Copy paper jams.

Copy paper not acceptable

Check if the copy paper is acceptable for

 

for the equipment is being

the equipment.

 

used.

P.31 “Paper types not acceptable”

 

The size of the copy paper in

Register the size of the placed copy paper

 

the drawer or on the bypass

properly.

 

tray is not registered prop-

P.36 “Preparation 3 - Registering Size

 

erly in the equipment.

of Paper Placed”

 

 

P.49 “Bypass copying”

 

Jammed paper is located in

Use the paper jam position lamp to

 

a place you cannot see eas-

recheck the position where the paper jam

 

ily.

has occurred.

 

 

P.75 “Paper Jams”

 

There is no gap between the

Adjust the gap between the side guides

 

side guides and paper in the

and the paper properly.

 

drawer. Or the gap is too

P.32 “Placing paper in drawers”

 

wide.

 

Multiple feeding occurs.

Paper is clinging to each

Fan the paper well and place it again.

 

other.

 

Image trouble

Phenomenon

Usual cause

Countermeasure

The density of the copy

Toner has run out.

The toner lamp blinks when toner has run

image is light.

 

out. Replace the toner cartridge if it is

 

 

blinking.

 

 

P.85 “Replacing Toner Cartridge”

 

The copy density is set

Make the density darker if you use the

 

lighter.

manual copy density mode. Or use the

 

 

automatic copy density mode.

 

The transfer charger wire is

Clean the transfer charger wire.

 

dirty.

P.98 “Cleaning transfer charger”

The density of the copy

The copy density is set

Make the density lighter if you use the

image is dark.

darker.

manual copy density mode. Or use the

 

 

automatic copy density mode.

The copied image is stained.

The Automatic Document

Lower them fully to block outside light.

 

Feeder (optional) or the

 

 

Platen Cover (optional) is not

 

 

lowered fully.

 

 

The original glass, platen

Clean them.

 

sheet, scanning area or

P.96 “Daily Inspection”

 

guides are dirty.

 

 

The copy density is set

Make the density lighter if you use the

 

darker.

manual copy density mode. Or use the

 

 

automatic copy density mode.

 

Highly transparent originals

Place a blank sheet of paper, the same

 

such as OHP films or tracing

size as the original or larger, over the orig-

 

paper are used.

inal.

92 Before Calling Service Technician

Image 94
Contents Operators Manual for Copying Functions Page Preface PrefaceFCC Notice How to read this manual Symbols in this manual Before Reading This ManualDescription of original/paper direction TrademarksContents Changing of the Enabled Energy Saving Mode Adjusting Density LevelSwitching Operation Sound On/Off When Message Lamp is Lit/BlinkingDaily Inspection Cleaning charger Cleaning transfer charger 105Contents Cartridge detecting function Toshiba Quality Is Second to NoneRecommended toner cartridges Toner remaining check functionToner Supplies / PartsGeneral General Precautions When installing or movingOther points 31.5When using the equipment Position of Certification label, etc During maintenance or inspection When handling suppliesFirst-aid measures Disclaimer Notice PorationSleep mode / Super sleep mode Energy saving featuresLow power mode Environmental InformationDescription of Each Component Preparation 1 Turning Power onPreparation 2 Placing Copy Paper Platen Cover optional, KA-1650PC Description of Each ComponentFront / Right side Automatic Document Feeder optional, MR-2020Left side / Inner side Original scale USB terminal 4-pinReceiving tray Scanning area Platen sheetConfiguration of options Control panel Original setting lamp Original mode button/lampsDensity adjustment buttons/lamps Interrupt button/lampOriginal button/lamps Copy button/lampsAPS/AMS selecting button/lamps Turning power OFF Preparation 1 Turning Power onTurning power on Press the power switch to on sideTo turn the equipment into the energy saving mode manually Saving energy when not in use Energy saving modeTypes of energy saving mode Canceling conditions for energy saving modeSuper sleep mode Acceptable media types Preparation 2 Placing Copy PaperFeeder Media type Paper size Maximum sheet Capacity *1 Storing paper Recommended paperPaper types not acceptable Media type Product namePlacing paper in drawers Press down the paper plateWiden the gap with both hands Adjust the side guides to the desired paper size Place paper in the drawerDo not let your fingers be caught when closing the drawer Register the paper size into the equipmentPreparation 3 Registering Size of Paper Placed Registering standard size LD, LT, LT-R, LG, ST-RRegistering other standard sizes Code NoPress the Start button Placing Originals Using Bypass TrayMaking Copies Acceptable originals Setting position Type of origiPlacing Originals Maximum number of originals scanned in one goPlacing originals on the original glass Placing booklet-type originals such as books or catalogs When black streaks appear on the copied image Using Automatic Document Feeder optionalPrecautions for Automatic Document Feeder optional Media types Maximum size Maximum number Paper weightWhen placing a large amount of originals with a long width Placing originals on Automatic Document Feeder optionalPlace the original Making CopiesCheck if paper is placed in the drawer Select the copy modes as requiredStopping/Resuming copying When the number of sheets exiting has exceededWhen the paper has run out Press the CLEAR/STOP button during scanning or copyingInterrupting copying and making another copy Interrupt copy Press the Interrupt buttonUsing Bypass Tray Media type Paper size Maximum sheet Capacity *1Bypass copying Placed on the bypass tray is lit Paper size has been registeredZooming In/Out Copy Image Default Settings Paper SelectionAutomatic paper selection APS Manual paper selection Default Settings Contents Default setting at installationPlace the original on the Automatic Document Feeder Paper SelectionAutomatic paper selection APS Automatic paper selection APSManual paper selection Place paper in the drawer Place the originalSelecting the drawer of the equipment Automatic magnification selection AMS Zooming In/Out Copy ImageAutomatic magnification selection AMS Specifying reproduction ratio manuallyIf the Function Clear lamp is blinking and copying stops Specifying both the sizes of the original and the copy paper Desired reproduction ratio appears Specifying reproduction ratio manuallyPress Zooming out or Zooming in button untilZooming In/Out Copy Image Copying in Same Page Order as Originals Sort Copying Press the Sort buttonOriginal is scanned Sort buttonButton Repeat this until all originals have been scannedCopying Both Sides of Card into 1 Page ID Card Page Selecting Image Mode To return it to the automatic copy density mode Adjusting Density LevelTo adjust the density to the desired level DarkSettings and Management of Equipment Switching Operation Sound On/Off All lamps on Sound on All lamps off Sound offChecking Total Number Copied Switch the display to check the rest of the total numberPress and hold Button for more than two seconds Auto sleep time Changing of the Enabled Energy Saving ModePress Button to switch the enabled mode Zooming in button to changeTroubleshooting When Message Lamp is Lit/Blinking Paper JamsPaper empty lamp When Message Lamp is Lit/BlinkingCover open lamp Toner lampPaper jam lamp Recommended toner cartridgesService call lamp Paper Jams When paper jams occur frequentlyChecking position of paper jams Open the Automatic Document Feeder When releasing jammed paperPaper jams within Automatic Document Feeder optional Lower Do not tear jammed paperPaper Jams Paper jams within Automatic Document Feeder optional Upper Raise the lever and open the upper coverPaper Jams Paper jams on bypass tray Pull out the paper jammed on the bypass trayPaper jam behind transfer unit Paper jams within fuser unit Close the transfer unit and the side coverPaper Jams Paper jams within Paper Feed Unit optional Open the front cover Hold down the green lever Replacing Toner CartridgeNever attempt to incinerate toner cartridges Pull out the toner cartridge Clean the charger Replacing Toner Cartridge With the transfer charger wire General operation Before Calling Service TechnicianPhenomenon Usual cause Countermeasure Toner-related items Original/Copy paper-related itemsImage trouble Before Calling Service Technician Page Maintenance and Inspection Daily InspectionDaily Inspection Original glass Guides Platen sheetCleaning charger Open the front cover Clean the chargerCleaning transfer charger Daily Inspection Page Specifications of Options 104 STUDIO181 Specifications 102Continuous copying speed 103 Packing list STUDIO181 Specifications OPCPacking list Continuous copying speedPaper size Feeder Continuous Copying speed Automatic Document Feeder Specifications of OptionsPaper Feed Unit Index 102 Page Multifunctional Digital Systems