Toshiba BDRV-WBX8-Z31 Version 7.2.4 M-3 manual CENTRO. Mode → ECP Plug & PLAY→ on

Page 42

2.7Installation under Windows 2000 (Parallel interface with Plug & Play Enabled)

Note: Proper operation is not guaranteed on the PC running Windows 2000.

1. Connect the printer to the PC with a parallel interface cable.

2. Turn on the printer.

3. Set the printer parameters in the system mode.

B-SX4, B-SX4-CN, B-SX5, and B-SX5-CN

CENTRO. MODE → ECP

PLUG & PLAY→ ON

B-SA4G, B-SA4G-CN, B-SA4T, B-SA4T-CN, B-852-R, B-452-R, B-SX6T-R, B-SX8T-R, B-EX4T1-G, B-EX4T1-T, B-EX4T2-G, B-EX4T2-T, B-EX4T2-H

PLUG & PLAY → ON

Note: For the parameter setting procedure, refer to Section 6.2 Parameter Setting on the Printer.

4. Turn on the PC.

Note: Log on as the user with administrative privilege.

5. After the system started, new hardware is detected. When the “Welcome to the Found New Hardware Wizard” is displayed, click the [Next] button.

6. Select “Search for a suitable driver for my device (recommended)”, then click the [Next] button.

- 40 -

Image 42

Contents Printer Driver Table of Contents Introduction Features Applicable printersNotation Screens Used in This DocumentTrademark and Copyright Operational Conditions Operation SystemSpecifying a network path for the printer port Configuration for the Status Monitor InterfaceXON/XOFF Page User Page Page How to open the Properties with the administrative privilege How to set up Windows Vista/Server2008/7/Server2008R2 againPage Preparatory Procedure Common to All Models Printer driver installation methodInstallation method by operating systems SX4, B-SX4-CN, B-SX5, and B-SX5-CNPreparation for Installation Page Installation under Windows XP/Server2003 Page List of the installable printer is displayed Page Page To print on the shared printer How to Enable Bi-directional Communication Support Installation under Windows Vista/Server2008/7/Server2008R2 TEC B-SA4G SA4TM-GS12-QM-R TEC EP2DL-GH20-QM-R Page Bi-directional Communication Support How to Enable Bi-directional Communication Support Read before installation Page Installation starts Page Page Page Page Enable Bi-directional Communication Support Page CENTRO. Mode → ECP Plug & PLAY→ on Page Page SX4, B-SX4-CN, B-SX5, and B-SX5-CN Communication Support Page Uninstalling the Printer Driver Uninstalling the printer driverCase of deleting the printer drivers except for V7.2.4 M-3 Page Page To delete the V6.5 Build75 or V6.5 Build77 „ Property setting menus in the Printing Preferences Function Description SupportFunction Description Support Function Description Support „ Property setting menus in the Properties Font Tools Printer fontFunction Description Support Reference „ Orientation Setup Tab„ Stock NameMirror Image „ Preset„ Effects Negative„ Automatic Preset Selection „ Label Size„ Exposed liner width New „ Preset ManagementUpdate Delete„ Printing Position „ User Commands tabDefault Orientation Horizontal Offset„ Driver Option tab Enable SubstitutionDefault Copies Function CharacterDisable Copies Limit Disable User-Defined Paper Size„ Dithering „ ResolutionGraphics Tab „ Color Control„ Media Settings Stock TabPrint Method Sensor „ Issue SettingsIssue Mode Label Gap„ Fine Adjustment Transfer Mode „ Print Density Adjustment„ Feed Adjustment Options Tab„ Supply Options „ Ribbon Adjustments„ Multiple Part Print Area Settings „ Multiple Part Print AreaMultiple Part Print Area High Density Adjustment Multiple Part High Density Print AreaType „ Ribbon Motor Voltage Adjustment„ Ribbon Type Rewind MotorNew Bar Code Font Fonts Tab„ Font EditScalable Font Settings „ View„ Tools Utility Font Settings Bitmap Font SettingsCompatibility Settings List Bar Code and Rfid Fonts When this‹ Encoding tab Text EncodingsJoin Multiple Lines Font NameEncoding Width„ Symbology Specific Options „ Bar Code OptionsTools Tab „ PrinterManage XML Data Print Files Reset PrinterSend Printer Command Test Print HeadCommand Protocol Configure Memory„ Driver Ribbon SettingsAdministration tab Format MemoryNetwork Settings tab Regional Options tabLanguage Selection Printer Specifications tab Logging tabPrinter Code Recording tab Status tab Status Display OptionsJob Verification tab Communication tab„ Example of bar code font programming Visual Basic 5.0/6.0 Designation of Printer Font„ Example of selecting a font on the application Character font Bar code font„ Restrictions of Bar Code Fonts Control code Input data 203dpi 600dpi Specified size Print size System Configuration System Configuration Example PC #1 PC #2 Printer server Centronics Addition/Deletion of Standard TCP/IP Port Addition Page Page Deletion How to Enable Bi-directional Communication Support AppendixParameter Setting on the Printer How to Connect the Printer to LAN „ Printer Port Types