Toshiba BDRV-WBX8-Z31 Version 7.2.4 M-3 manual Operational Conditions, Operation System

Page 6

1.6 Operational Conditions

This product can be used under the following system requirements.

1.6.1Operation System

Windows 2000, Windows XP, Windows Server 2003, Windows Vista, Windows Server 2008, Windows 7 (32 bit/64 bit) or Windows Server 2008 R2

Notes: 1. 64-bit operating systems except Windows 7 and Windows Server 2008 R2 are not applicable.

2.Windows 2000 is not supported though installation of this product is possible.

1.6.2Hardware

A DOS/V (IBM AT compatible) machine running the above Windows operation system must be used along with the following mandatory or recommended requirements.

	Requirement	Recommendation
CPU	Intel® Pentium® II 400MHz or greater	Intel® Pentium® III 1GHz or greater
Memory	64MB or more	256MB or more
HDD	10MB or more free size

1.7 Cautions for Installation (IMPORTANT)

Please be sure to read the following cautions before using this product.

When you are going to install an upgraded version of the TEC printer driver, you must first uninstall the older version in advance. For how to uninstall the printer driver, refer to Section 2.10 Uninstalling the

Printer Driver.

Failure to do so may cause unstable printing operations due to the influences of the files and registry related to the old version remaining in the system. Follow the procedure in Section 2.10 Uninstalling the Printer Driver, and the files and registry related to the printer driver will be deleted from the system.

Note: • This printer driver uses common program for the all applicable printer models.

•Even if the printer model is different, TPCL printer driver of different version cannot be used on the same PC.

•When installing TPCL printer driver for a new model on the PC in which the TPCL printer driver of different version for another printer model has been already installed, the existing printer driver needs to be deleted.

When you are asked to select “Network” or “Local” in the Add Printer Wizard during the installation of the printer driver, be sure to choose “Local”. Even when the printer will be used as a network printer, first install the printer driver as a local printer, then specify a network path for the printer port later.

- 4 -

Image 6

Contents Printer Driver Table of Contents Introduction Features Applicable printersNotation Screens Used in This DocumentTrademark and Copyright Operational Conditions Operation SystemSpecifying a network path for the printer port Configuration for the Status Monitor InterfaceXON/XOFF Page User Page Page How to open the Properties with the administrative privilege How to set up Windows Vista/Server2008/7/Server2008R2 againPage Preparatory Procedure Common to All Models Printer driver installation methodInstallation method by operating systems SX4, B-SX4-CN, B-SX5, and B-SX5-CNPreparation for Installation Page Installation under Windows XP/Server2003 Page List of the installable printer is displayed Page Page To print on the shared printer How to Enable Bi-directional Communication Support Installation under Windows Vista/Server2008/7/Server2008R2 TEC B-SA4G SA4TM-GS12-QM-R TEC EP2DL-GH20-QM-R Page Bi-directional Communication Support How to Enable Bi-directional Communication Support Read before installation Page Installation starts Page Page Page Page Enable Bi-directional Communication Support Page CENTRO. Mode → ECP Plug & PLAY→ on Page Page SX4, B-SX4-CN, B-SX5, and B-SX5-CN Communication Support Page Uninstalling the Printer Driver Uninstalling the printer driverCase of deleting the printer drivers except for V7.2.4 M-3 Page Page To delete the V6.5 Build75 or V6.5 Build77 „ Property setting menus in the Printing Preferences Function Description SupportFunction Description Support Function Description Support „ Property setting menus in the Properties Font Tools Printer fontFunction Description Support Reference „ Orientation Setup Tab„ Stock NameMirror Image „ Preset„ Effects Negative„ Automatic Preset Selection „ Label Size„ Exposed liner width New „ Preset ManagementUpdate Delete„ Printing Position „ User Commands tabDefault Orientation Horizontal Offset„ Driver Option tab Enable SubstitutionDefault Copies Function CharacterDisable Copies Limit Disable User-Defined Paper Size„ Dithering „ ResolutionGraphics Tab „ Color Control„ Media Settings Stock TabPrint Method Sensor „ Issue SettingsIssue Mode Label Gap„ Fine Adjustment Transfer Mode „ Print Density Adjustment„ Feed Adjustment Options Tab„ Supply Options „ Ribbon Adjustments„ Multiple Part Print Area Settings „ Multiple Part Print AreaMultiple Part Print Area High Density Adjustment Multiple Part High Density Print AreaType „ Ribbon Motor Voltage Adjustment„ Ribbon Type Rewind MotorNew Bar Code Font Fonts Tab„ Font EditScalable Font Settings „ View„ Tools Utility Font Settings Bitmap Font SettingsCompatibility Settings List Bar Code and Rfid Fonts When this‹ Encoding tab Text EncodingsJoin Multiple Lines Font NameEncoding Width„ Symbology Specific Options „ Bar Code OptionsTools Tab „ PrinterManage XML Data Print Files Reset PrinterSend Printer Command Test Print HeadCommand Protocol Configure Memory„ Driver Ribbon SettingsAdministration tab Format MemoryNetwork Settings tab Regional Options tabLanguage Selection Printer Specifications tab Logging tabPrinter Code Recording tab Status tab Status Display OptionsJob Verification tab Communication tab„ Example of bar code font programming Visual Basic 5.0/6.0 Designation of Printer Font„ Example of selecting a font on the application Character font Bar code font„ Restrictions of Bar Code Fonts Control code Input data 203dpi 600dpi Specified size Print size System Configuration System Configuration Example PC #1 PC #2 Printer server Centronics Addition/Deletion of Standard TCP/IP Port Addition Page Page Deletion How to Enable Bi-directional Communication Support AppendixParameter Setting on the Printer How to Connect the Printer to LAN „ Printer Port Types