Toshiba BDRV-WBX8-Z31 Version 7.2.4 M-3 manual Uninstalling the Printer Driver

Page 48

2.10 Uninstalling the Printer Driver

2.10.1 To delete the printer drivers except for V6.5 Build75 and V6.5 Build77

In the following cases, be sure to uninstall the printer driver using the procedure below.

•When the same version is installed again.

•When an older version has been already installed.

•When the installation is canceled on the way or when the [No] is selected at a confirmation of the digital signature.

•When the printer driver cannot be installed for some reason.

Notes: 1. When installing the printer driver with Plug & Play enabled, turn OFF the printer first.

2When the printer driver is deleted, the information of the registered stocks and bar codes are also deleted. This information can be saved in a file beforehand by using the export function, and restored by using the import function after re-installation of the printer driver.

In the case of deleting the printer drivers except for V7.2.4 M-3

Before deleting the printer driver except for V7.2.4 M-3, follow the procedure described in Section 2.1 Preparation for Installation. Doing this causes the previously installed printer driver to be updated and creates the shortcut of the Driver Wizard in the TPCL Printer Driver of TOSHIBA TEC folder.

However, it is not possible to update the printer driver which is older than V6.9.3 M-0. For such versions, first delete “C:\TEC_DRV” folder, then conduct the Preparation for Installation. When the preparation is completed, the shortcut of the “Driver Wizard” is created in the TPCL Printer Driver folder.

In the case of deleting the printer driver of “To print on the shared printer (2)”

Before deleting the printer driver, delete the printer icon that was created when the shared printer was installed.

Uninstalling the printer driver

1. Select the “Start”, “All programs”, “TOSHIBA TEC”, “TPCL Printer Driver”, and “Driver Wizard”.

Note: Log on as the user with administrative privilege. Exit the all Windows applications before performing the above operation. Confirm that there is no print job in the spooler, then close the spooler and the printer folder.

In the case of Windows Vista/Server 2008/7/Server2008R2, the User Account Control screen may appear. In that case, click the [Allow].

- 46 -

Image 48

Contents Printer Driver Table of Contents Introduction Features Applicable printersNotation Screens Used in This DocumentTrademark and Copyright Operational Conditions Operation SystemSpecifying a network path for the printer port Configuration for the Status Monitor InterfaceXON/XOFF Page User Page Page How to open the Properties with the administrative privilege How to set up Windows Vista/Server2008/7/Server2008R2 againPage Preparatory Procedure Common to All Models Printer driver installation methodInstallation method by operating systems SX4, B-SX4-CN, B-SX5, and B-SX5-CNPreparation for Installation Page Installation under Windows XP/Server2003 Page List of the installable printer is displayed Page Page To print on the shared printer How to Enable Bi-directional Communication Support Installation under Windows Vista/Server2008/7/Server2008R2 TEC B-SA4G SA4TM-GS12-QM-R TEC EP2DL-GH20-QM-R Page Bi-directional Communication Support How to Enable Bi-directional Communication Support Read before installation Page Installation starts Page Page Page Page Enable Bi-directional Communication Support Page CENTRO. Mode → ECP Plug & PLAY→ on Page Page SX4, B-SX4-CN, B-SX5, and B-SX5-CN Communication Support Page Uninstalling the Printer Driver Uninstalling the printer driverCase of deleting the printer drivers except for V7.2.4 M-3 Page Page To delete the V6.5 Build75 or V6.5 Build77 „ Property setting menus in the Printing Preferences Function Description SupportFunction Description Support Function Description Support „ Property setting menus in the Properties Font Tools Printer fontFunction Description Support Reference Setup Tab „ Stock„ Orientation Name„ Preset „ EffectsMirror Image Negative„ Automatic Preset Selection „ Label Size„ Exposed liner width „ Preset Management UpdateNew Delete„ User Commands tab Default Orientation„ Printing Position Horizontal OffsetEnable Substitution Default Copies„ Driver Option tab Function CharacterDisable Copies Limit Disable User-Defined Paper Size„ Resolution Graphics Tab„ Dithering „ Color Control„ Media Settings Stock TabPrint Method „ Issue Settings Issue ModeSensor Label Gap„ Fine Adjustment „ Print Density Adjustment „ Feed AdjustmentTransfer Mode Options Tab„ Ribbon Adjustments „ Multiple Part Print Area Settings„ Supply Options „ Multiple Part Print AreaMultiple Part Print Area High Density Adjustment Multiple Part High Density Print Area„ Ribbon Motor Voltage Adjustment „ Ribbon TypeType Rewind MotorFonts Tab „ FontNew Bar Code Font EditScalable Font Settings „ View„ Tools Bitmap Font Settings Compatibility SettingsUtility Font Settings List Bar Code and Rfid Fonts When this‹ Encoding tab Text EncodingsFont Name EncodingJoin Multiple Lines Width„ Symbology Specific Options „ Bar Code OptionsTools Tab „ PrinterReset Printer Send Printer CommandManage XML Data Print Files Test Print HeadCommand Protocol Configure MemoryRibbon Settings Administration tab„ Driver Format MemoryNetwork Settings tab Regional Options tabLanguage Selection Printer Specifications tab Logging tabPrinter Code Recording tab Status tab Status Display OptionsJob Verification tab Communication tabDesignation of Printer Font „ Example of selecting a font on the application„ Example of bar code font programming Visual Basic 5.0/6.0 Character font Bar code font„ Restrictions of Bar Code Fonts Control code Input data 203dpi 600dpi Specified size Print size System Configuration System Configuration Example PC #1 PC #2 Printer server Centronics Addition/Deletion of Standard TCP/IP Port Addition Page Page Deletion How to Enable Bi-directional Communication Support AppendixParameter Setting on the Printer How to Connect the Printer to LAN „ Printer Port Types