Toshiba BDRV-WBX8-Z31 Version 7.2.4 M-3 manual Xon/Xoff

Page 9

2.Whenever the “CENTRO. MODE” is set to “ECP” in the printer system mode, be sure to set the “PLUG & PLAY” to ON. And, whenever the “CENTRO. MODE” is set to “SPP”, be sure to set the “PLUG & PLAY” to OFF. (The “CENTRO. MODE” and “PLUG & PLAY” have been set to “SPP” and “OFF” as the factory default settings, respectively.

To enable the bi-directional communication, be sure to set the “CENTRO. MODE” to “ECP” and “PLUG & PLAY” to “ON”.

For details of the printer parameter setting, refer to Section 6.2 Parameter Setting on the Printer.

If printing is performed with the status monitor enabled though this feature is not available or not necessary, delete the print job and disable the [Printer Status Monitoring].

If you start the status monitor by mistake, close the status monitor and disable the [Printer Status Monitoring].

When the status monitor is used to monitor the printer statuses, do not install more than one printer driver specifying the same output port in one host PC. When more than one printer driver is installed in a PC, disable the [Printer Status Monitoring]. Also, when multiple computers connect to the same printer, specify that printer as the shared printer or disable the [Printer Status Monitoring.

When using this product for the B-419 printer, select the standard COM port for the output port. Also, place the B-419 printer in the “high speed graphic mode” and configure the port settings as shown below. For how to set the printer mode, refer to the Owner’s Manual of the printer.

Bits/sec.:	38400
Data bit:	8
Parity:	Even
Stop bit:	1
Flow control:	XON/XOFF

When Kanji characters are used as bar code font data, click the [Tool] tab – [Configure] button – [Printer Options], and select the “ESC/LF/NUL” for the “Control Codes” of the “Command Protocol”.

Bar code font types that accept Kanji data: PDF417, MicroPDF417, Data Matrix, Maxicode, QR code

The default setting of the “Control Codes” is “Standard”. Be sure to change this setting when you print Kanji characters as bar code data, otherwise an error results.

- 7 -

Image 9

Contents Printer Driver Table of Contents Introduction Applicable printers FeaturesNotation Screens Used in This DocumentTrademark and Copyright Operation System Operational ConditionsSpecifying a network path for the printer port Interface Configuration for the Status MonitorXON/XOFF Page User Page Page How to set up Windows Vista/Server2008/7/Server2008R2 again How to open the Properties with the administrative privilegePage Printer driver installation method Preparatory Procedure Common to All ModelsSX4, B-SX4-CN, B-SX5, and B-SX5-CN Installation method by operating systemsPreparation for Installation Page Installation under Windows XP/Server2003 Page List of the installable printer is displayed Page Page To print on the shared printer How to Enable Bi-directional Communication Support Installation under Windows Vista/Server2008/7/Server2008R2 TEC B-SA4G SA4TM-GS12-QM-R TEC EP2DL-GH20-QM-R Page Bi-directional Communication Support How to Enable Bi-directional Communication Support Read before installation Page Installation starts Page Page Page Page Enable Bi-directional Communication Support Page CENTRO. Mode → ECP Plug & PLAY→ on Page Page SX4, B-SX4-CN, B-SX5, and B-SX5-CN Communication Support Page Uninstalling the Printer Driver Uninstalling the printer driverCase of deleting the printer drivers except for V7.2.4 M-3 Page Page To delete the V6.5 Build75 or V6.5 Build77 Function Description Support „ Property setting menus in the Printing PreferencesFunction Description Support Function Description Support Font Tools Printer font „ Property setting menus in the PropertiesFunction Description Support Reference „ Stock Setup Tab„ Orientation Name„ Effects „ PresetMirror Image Negative„ Automatic Preset Selection „ Label Size„ Exposed liner width Update „ Preset ManagementNew DeleteDefault Orientation „ User Commands tab„ Printing Position Horizontal OffsetDefault Copies Enable Substitution„ Driver Option tab Function CharacterDisable User-Defined Paper Size Disable Copies LimitGraphics Tab „ Resolution„ Dithering „ Color Control„ Media Settings Stock TabPrint Method Issue Mode „ Issue SettingsSensor Label Gap„ Fine Adjustment „ Feed Adjustment „ Print Density AdjustmentTransfer Mode Options Tab„ Multiple Part Print Area Settings „ Ribbon Adjustments„ Supply Options „ Multiple Part Print AreaMultiple Part High Density Print Area Multiple Part Print Area High Density Adjustment„ Ribbon Type „ Ribbon Motor Voltage AdjustmentType Rewind Motor„ Font Fonts TabNew Bar Code Font EditScalable Font Settings „ View„ Tools Compatibility Settings Bitmap Font SettingsUtility Font Settings List Bar Code and Rfid Fonts When thisText Encodings ‹ Encoding tabEncoding Font NameJoin Multiple Lines Width„ Bar Code Options „ Symbology Specific Options„ Printer Tools TabSend Printer Command Reset PrinterManage XML Data Print Files Test Print HeadConfigure Memory Command ProtocolAdministration tab Ribbon Settings„ Driver Format MemoryNetwork Settings tab Regional Options tabLanguage Selection Printer Specifications tab Logging tabPrinter Code Recording tab Status Display Options Status tabCommunication tab Job Verification tab„ Example of selecting a font on the application Designation of Printer Font„ Example of bar code font programming Visual Basic 5.0/6.0 Character font Bar code font„ Restrictions of Bar Code Fonts Control code Input data 203dpi 600dpi Specified size Print size System Configuration System Configuration Example PC #1 PC #2 Printer server Centronics Addition/Deletion of Standard TCP/IP Port Addition Page Page Deletion Appendix How to Enable Bi-directional Communication SupportParameter Setting on the Printer „ Printer Port Types How to Connect the Printer to LAN