NETGEAR WAG102NA manual Technical Support, Trademarks, Statement of Conditions

Page 2

ProSafe Dual Band Wireless Access Point WAG102 Reference Manual (802.11a/g)

Technical Support

Please register to obtain technical support. Please retain your proof of purchase and warranty information.

To register your product, get product support or obtain product information and product documentation, go to http://www.NETGEAR.com. If you do not have access to the World Wide Web, you may register your product by filling out the registration card and mailing it to NETGEAR customer service.

You will find technical support information at: http://www.NETGEAR.com/ through the customer service area. If you want to contact technical support by telephone, see the support information card for the correct telephone number for your country.

© 2006 by NETGEAR, Inc. All rights reserved.

Trademarks

NETGEAR and the NETGEAR logo are registered trademarks, and ProSafe is a trademark, of NETGEAR, INC. Windows is a registered trademark of Microsoft Corporation. Other brand and product names are trademarks or registered trademarks of their respective holders. Information is subject to change without notice. All rights reserved.

Statement of Conditions

In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to make changes to the products described in this document without notice. NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit layout(s) described herein.

Modifications made to the product, unless expressly approved by Netgear, could void the user’s authority to operate the equipment. NETGEAR does not assume any liability that may occur due to such condition.

Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice

ProSafe 802.11a/g Dual Band Wireless Access Point

Tested to Comply with FCC Standards

FOR HOME OR OFFICE USE

FCC ID: PY3WAG102

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference.

This device must accept any interference received, including interference that may cause undesired operation.

Placement and Range Guidelines

Indoors, computers can connect over 802.11 wireless networks at a maximum range of 500 feet (152.4 m) for 802.11b devices. However, the operating distance or range of your wireless connection can vary significantly, based on the physical placement of the wireless access point.

For best results, identify a location for your wireless access point according to these guidelines:

ii

v2.0, September 2006

Image 2
Contents NETGEAR, Inc Trademarks Placement and Range GuidelinesTechnical Support Statement of ConditionsFCC Statement FCC Requirements for Operation in the United StatesIndustry Canada Compliance Statement Europe EU Declaration of Conformity V2.0, September Channels 1 to Antenna Statement for the European CommunityEuropean Spectrum Usage Rules Effective April 11 36,40,44,48Product and Publication Details Bestätigung des Herstellers/ImporteursCertificate of the Manufacturer/Importer Contents Chapter Management Appendix a Default Settings and Technical Specifications Xii About This Manual Conventions, Formats and ScopeHow to Use This Manual How to Print this Manual Xvi Chapter Introduction Key Features and Standards Supported Standards and ConventionsKey Features 802.11a/g Standards-based Wireless Networking Autosensing Ethernet Connections with Auto UplinkCompatible and Related Netgear Products System RequirementsWhat’s In the Box? Front Panel Front Panel LED IndicatorsHardware Description Rear Panel LED Description LINK/ACT LANV2.0, September V2.0, September Chapter Basic Installation and Configuration Wireless Equipment Placement and Range Guidelines Understanding WAG102 Wireless Security Options LUHOHVVDWD 6HFXULW\2SWLRQVInstalling the WAG102 Wireless Access Point Setting up the WAG102 Wireless Access PointConfiguring LAN and Wireless Access V2.0, September V2.0, September V2.0, September V2.0, September Deploying the WAG102 Wireless Access Point Verifying Wireless ConnectivityLogging In Using the Default IP Address Setting Basic IP Options V2.0, September Wireless Settings Configuring 802.11a Wireless SettingsV2.0, September Configuring 802.11b/g Wireless Settings Setting Up and Testing Basic Wireless Connectivity V2.0, September Understanding Security Profiles Network Authentication Types Typea DescriptionData Encryption Settings Type a DescriptionV2.0, September Ssid and WEP/WPA Settings Setup Form 802.11a Configuration802.11b/g Configuration Configuring the Radius Server Settings V2.0, September Setting up a Security Profile V2.0, September Configuring WEP V2.0, September Configuring WPA with Radius Configuring WPA2 with Radius Configuring WPA and WPA2 with Radius Click Apply to save your Radius settingsConfiguring WPA-PSK Configuring WPA2-PSK Configuring WPA-PSK and WPA2-PSK Enter the WPA Passphrase Network KeyRestricting Wireless Access by MAC Address V2.0, September Chapter Management Remote ManagementUsing Syslog and Activity Log Information Viewing General Summary Information General Information FieldsField Description V2.0, September Viewing Network Traffic Statistics Viewing Available Wireless Station List Statistics FieldsUpgrading the Wireless Access Point Software V2.0, September Configuration File Management Saving and Retrieving the ConfigurationRestoring the WAG102 to the Factory Default Settings Changing the Administrator Password Chapter Advanced Configuration Hotspot SettingsConfiguring Advanced Wireless Settings Enabling Wireless Bridging and Repeating V2.0, September Configuring a WAG102 as a Point-to-Point Bridge Configuring a Point-to Configuring the WAG102 as a Wireless Repeater Verify the following parameters for all access points Click Apply to save your settings V2.0, September Chapter Troubleshooting No lights are lit on the wireless access pointWireless LAN activity light does not light up LAN light is not litCannot connect to the WAG102 to configure it When I enter a URL or IP address I get a timeout errorUsing the Reset Button to Restore Factory Default Settings Table A-1. Access Point Default Configuration Settings Appendix a Default Settings and Technical SpecificationsFactory Default Settings GMT Technical Specifications Table A-2. WAG102 Technical SpecificationsV2.0, September Appendix B Related Documents Document LinkV2.0, September Index NumericsIndex-2 Index-3 Index-4 Index-5 Index-6
Related manuals
Manual 8 pages 7.82 Kb